JVC LT-32VH3105 32-Inch Smart LED User Guide
- June 6, 2024
- JVC
Table of Contents
JVC LT-32VH3105 32-Inch Smart LED User Guide
Quick Start Guide
-
Insert the batteries Into the Remote Control
Insert two AAA/R3 or equivalent type batteries inside. Observe the correct polarity (+/-) when inserting batteries and replace the battery cover.
-
Connect the antenna to your TV
The back connection options may differ depending on the model
REAR SIDE OF THE TV
-
Connect the TV to the mans socket
-
To switch the TV on (depending on the model)
After connecting the power cord to the mans socket, the standby LED lights up.
To switch on the TV from standby mode ether; -
Press the button, Standby a numeric button or Programme +/- button on the remote control.
——— or ——— -
a. Press the middle of the side function switch on the TV in.
b. Press the control button on the TV.
The appearance of the remote control buttons and the positon of the control buttons on the TV may differ depending on the model -
HDMI Input
PLEASE ENSURE BOTH UNITS ARE SWITCHED OFF BEFORE CONNECTING. Use a HDMI to HDMI cable to connect the two units together. To select the HDMI input, press the Source button on the remote control. Each time t s pressed the on- screen menu confirms your selection.
The appearance of the Source button may differ depending on the model of the remote control
To HDMI connection on the device
-
Auto Setup procedure
When turned on for the first time, the language selection screen is displayed. Select the desired language and press OK.
On the next screen set your country preference. Then press OK to continue.
Select Home Mode for home use. You can activate Store Mode option at this point if necessary,
however, this option is only intended for store use.
Depending on the model of your TV and the country selection Privacy Settings menu may appear at this point. Using this menu you can set your privacy privileges. Highlight a feature and use Left and Right directional buttons to enable or disable. If the Internet Connection option is disabled Network/Internet Settings screen will be skipped and not displayed.
Highlight Next and press OK button on the remote control to continue and the Network/Internet Settings menu will be displayed.
Refer to Connect your TV to the internet section to configure a wired or a wireless connection.
After the settings are completed highlight Next and press OK button to continue.
Broadcast Search;
On the next screens et your preferences.
Scan Encrypted Channels : On
Select favorite network type: Satellite- D. Aerial ○
- D. Cable ○
- Satellite ●
- Analogue ○
When finished, highlight Next and press OK to start channel scan.
After the initial settings are completed TV will start to search for available broadcasts of the selected broadcast types.
While the search continues a message may appear, asking whether you want to sort channels according to the LCN(). Select Yes and press OK to confirm.
() LCN is the Logical Channel Number system that organizes available broadcasts in accordance with a recognizable channel number sequence (if available).
After the channel scan has been completed the Choose Region menu may appear. Select the appropriate settings for your location using the directional buttons then press OK.
After all the available stations are stored, Channels menu will be displayed. You can edit the channel list according to your preferences using the Edit tab options or press the Menu button to quit and watch TV.
Note: Do not turn off the TV while initializing first time installation. Note that, some options may not be available depending on the country selection.
-
Connect your TV to the Internet
Connectivity feature allows you to connect your TV to the home network wired or wirelessly. You can use this networking system to connect to internet or to access photo, video and audio files that are stored on a Media server connected to the network and play/display them on the TV.
However, f your TV does not have Wireless USB dongle or doesn’t support internal WLAN feature, you should use wired connection type. Add your TV to your home network by connecting t to the modem/router via an LAN cable (not supplied) as illustrated.
To use your TV with your wireless network, you may need a WLAN USB dongle. You should connect t to one of the USB inputs on the TV. If your TV supports internal WLAN feature you won’t need a wireless LAN adaptor.
Press the Menu button to open the man TV menu. Select Settings by using the directional buttons, highlight Network and press OK. While Network Type s highlighted, press Left or Right buttons to select connection type. Wired connection will be established automatically. If wireless connection s selected, highlight Scan Wireless Networks and press OK. The TV will search for the available wireless networks and list them when finished. Select one and press the OK button to connect. If the wireless network s password-protected you should enter the correct password to access the network.
Note: For more detailed information refer to the manual installed on your TV. To access this manual, enter Settings menu, select Manuals and press OK. For quick access press Menu button and then Info button.-
Wireless Connection
or
-
Wired Connection
(depending on the model)
-
Dear Customer
This apparatus is in conformance with the valid European directives and
standards regarding electromagnetic compatibility and electrical safety.
European representative of the manufacturer is:
Vestel Germany GmbH
Parkring 6
85748 Garching b.München
Germany
Accessories Included
-
Remote Control
-
Batteries: 2 x AAA
-
Quick Start Guide
Depends on model -
Side AV Connection Cable
-
YPbPr Connection Cable
-
WLAN USB Dongle and USB Extension Cable
-
Wall Mount Kit
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
In extreme weather (storms, lightning) and long inactivity periods (going on holiday) disconnect the TV set from the mains.
The mains plug is used to disconnect TV set from the mains and therefore it must remain readily operable. If the TV set is not disconnected electrically from the mains, the device will still draw power for all situations even if the TV is in standby mode or switched off.
Note: Follow the on screen instructions for operating the related features.
IMPORTANT – Please read these instructions fully before installing or operating
WARNING: This device is intended to be used by persons (including children) who are capable / experienced of operating such a device unsupervised, unless they have been given supervision or instruction concerning the use of the device by a person responsible for their safety.
-
Use this TV set at an altitude of less than 5000 meters above the sea level, in dry locations and in regions with moderate or tropical climates.
-
The TV set is intended for household and similar indoor use but may also be used in public places.
-
For ventilation purposes, leave at least 5cm of free space around the TV.
-
The ventilation should not be impeded by covering or blocking the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.
-
The power cord plug should be easily accessible. Do not place the TV, furniture, etc. on the power cord.
A damaged power cord/plug can cause fire or give you an electric shock. Handle the power cord by the plug, do not unplug the TV by pulling the power cord.
Never touch the power cord/plug with wet hands as this could cause a short circuit or electric shock.
Never make a knot in the power cord or tie it with other cords. When damaged it must be replaced, this should only be done by qualified personnel. -
Do not expose the TV to dripping or splashing of liquids and do not place objects filled with liquids, such as vases, cups, etc. on or over the TV (e.g., on shelves above the unit).
-
Do not expose the TV to direct sunlight or do not place open flames such as lit candles on the top of or near the TV.
-
Do not place any heat sources such as electric heaters, radiators, etc. near the TV set.
-
Do not place the TV on the floor and inclined surfaces.
-
To avoid danger of suffocation, keep plastic bags out of the reach of the babies, children and domestic animals.
-
Carefully attach the stand to the TV. If the stand is provided with screws, tighten the screws firmly to prevent the TV from tilting. Do not over-tighten the screws and mount the stand rubbers properly.
-
Do not dispose of the batteries in fire or with hazardous or flammable materials.
WARNING – Batteries must not be exposed to excessive heat such as sunshine, fire or the like.
WARNING – Excessive sound pressure from earphones or headphones can cause hearing loss. ABOVE ALL – NEVER let anyone, especially children, push or hit the screen, push anything into holes, slots or any other openings in the case.
Caution
| Serious injury or death risk
---|---
Risk of electric shock
| Dangerous voltage risk
Maintenance
| Important maintenance component
Markings on the Product
The following symbols are used on the product as a marker for restrictions and precautions and safety instructions. Each explanation shall be considered where the product bears related marking only. Note such information for security reasons.
Class II Equipment:** This appliance is designed in such a way that it does not require a safety connection to electrical earth.
Hazardous Live Terminal:** The marked terminal(s) is/are hazardous live under normal operating conditions.
-
Caution, See Operating Instructions: The marked area(s) contain(s) user replaceable coin or button cell batteries. -
Class 1 Laser Product: This product contains Class 1 laser source that is safe under reasonably foreseeable conditions of operation.
WARNING
Do not ingest the battery, Chemical Burn Hazard This product or the accessories supplied with the product may contain a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and
keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
– – – – – – – – – – – –
A television may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as:
- ALWAYS use cabinets or stands or mounting methods recommended by the manufacturer of the television set.
- ALWAYS use furniture that can safely support the television set.
- ALWAYS ensure the television set is not overhanging the edge of the supporting furniture.
- ALWAYS educate children about the dangers of climbing on furniture to reach the television set or its controls.
- ALWAYS route cords and cables connected to your television so they cannot be tripped over, pulled or grabbed.
- NEVER place a television set in an unstable location.
- NEVER place the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television set to a suitable support.
- NEVER place the television set on cloth or other materials that may be located between the television set and supporting furniture.
- NEVER place items that might tempt children to climb, such as toys and remote controls, on the top of the television or furniture on which the television is placed.
- The equipment is only suitable for mounting at heights ≤2 m.
If the existing television set is going to be retained and relocated, the same
considerations as above should be applied.
– – – – – – – – – – – –
Apparatus connected to the protective earthing of the building installation through the MAINS connection or through other apparatus with a connection to protective earthing – and to a television distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to a television distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator)
WALL MOUNTING WARNINGS
- Read the instructions before mounting your TV on the wall.
- The wall mount kit is optional. You can obtain from your local dealer, if not supplied with your TV.
- Do not install the TV on a ceiling or on an inclined wall.
- Use the specified wall mounting screws and other accessories.
- Tighten the wall mounting screws firmly to prevent the TV from fall. Do not over-tighten the screws.
Figures and illustrations in this user manual are provided for reference only and may differ from the actual product appearance. Product design and specifications may be changed without notice.
License Notification
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo
are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and
the double-D symbol are trademarks of Dolby Laboratories Licensing
Corporation.
YouTube and the YouTube logo are trademarks of Google Inc.
Depends on model
For DTS patents, see http://patents.dts.com. Manufactured under license from
DTS Licensing Limited. DTS, the Symbol, DTS and the Symbol together, DTS-HD,
and the DTS-HD logo are registered trademarks or trademarks of DTS, Inc. in
the United States and/or other countries. © DTS, Inc. All Rights Reserved.
For DTS patents, see http://patents.dts.com. Manufactured under license from
DTS Licensing Limited. DTS, the Symbol, DTS and the Symbol together,
Virtual:X, and the DTS Virtual:X logo are registered trademarks or trademarks
of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All
Rights Reserved.
Depends on model
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Vestel Elektronik Sanayi ve Ticaret A.S. is under license. Other trademarks and trade names are those of their respective owners.
This product contains technology subject to certain intellectual property rights of Microsoft. Use or distribution of this technology outside of this product is prohibited without the appropriate license(s) from Microsoft.
Content owners use Microsoft PlayReady™ content access technology to protect their intellectual property, including copyrighted content. This device uses PlayReady technology to access PlayReady-protected content and/or WMDRM- protected content. If the device fails to properly enforce restrictions on content usage, content owners may require Microsoft to revoke the device’s ability to consume PlayReady-protected content. Revocation should not affect unprotected content or content protected by other content access technologies. Content owners may require you to upgrade PlayReady to access their content. If you decline an upgrade, you will not be able to access content that requires the upgrade.
The “CI Plus” Logo is a trademark of CI Plus LLP.
This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary.
DVB is a registered trademark of the DVB Project.
This product is manufactured, distributed and warranted exclusively by VESTEL
TicaretA.Ş and serviced by its designated service providers. “JVC” is the
trademark of JVC KENWOOD Corporation, used by such companies under license.
Wall mounting instructions (depending on the model)
Wall Mounting the TV
The TV can be mounted on a wall using a MX XX mm () VESA mounting kit
supplied separately. Remove the base stand as shown. Mount the TV according to
the instructions supplied with the kit. Beware of electrical cables, gas and
water pipes in the wall. In case of any doubt please contact a qualified
installer. The screw thread length must not exceed X mm (*) into the TV.
Contact the store where you purchased the product for information on where to
purchase the VESA kit.
(*) Refer to the related additional page for the accurate VESA measurements and screw specifications.
Removing the base stand
- To remove the base stand, protect the screen and lay the TV flat on its face on a stable table with the base over the edge. Remove the screws fixing the stand to the TV.
Disposal Information
[European Union]
These symbols indicate that the electrical and electronic equipment and the battery with this symbol should not be disposed of as general household waste at its end-of-life. Instead, the products should be handed over to the applicable collection points for the recycling of electrical and electronic equipment as well as batteries for proper treatment, recovery and recycling in accordance with your national legislation and the Directive 2012/19/EU and 2013/56/EU.
By disposing of these products correctly, you will help to conserve natural resources and will help to prevent potential negative effects on the environment and human health which could otherwise be caused by inappropriate waste handling of these products.
For more information about collection points and recycling of these products, please contact your local municipal office, your household waste disposal service or the shop where you purchased the product. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
[Business users]
If you wish to dispose of this product, please contact your supplier and check the terms and conditions of the purchase contract.
[Other Countries outside the European Union]
These symbols are only valid in the European Union. Contact your local authority to learn about disposal and recycling.
The product and packaging should be taken to your local collection point for recycling.
Some collection points accept products free of charge.
Note: The sign Pb below the symbol for batteries indicates that this battery contains lead.
-
Products
-
Battery
Remote Control
*() MY BUTTON 1:**
This button may have default function depending on the model. However you can set a special function to this button by pressing on it for five seconds when on a desired source or channel. A confirmation message will be displayed on the screen. Now the My Button 1 is associated with the selected function.
Note that if you perform First Time Installation, My Button 1 will return to its default function.
Teletext Services
Press the Text button to enter. Press again to activate mix mode, which allows you to see the teletext page and the TV broadcast at the same time. Press once more to exit. If available, sections in the teletext pages will become color- coded and can be selected by pressing the colored buttons. Follow the instructions displayed on the screen.
Digital Teletext
Press the Text button to view digital teletext information. Operate it with the colored buttons, cursor buttons and the OK button. The operation method may differ depending on the contents of the digital teletext. Follow the instructions displayed on the digital teletext screen. When the Text button is pressed again, the TV returns to television broadcast.
- Standby: Switches On / Off the TV
- Numeric buttons: Switches the channel, enters a number or a letter in the text box on the screen
- Language: Switches among sound modes (analogue TV), displays and changes audio/subtitle language and turns subtitles on or off (digital TV, where available)
- Mute: Completely turns off the volume of the TV
- Volume +/-
- Guide: Displays the electronic programme guide
- Directional buttons: Helps navigate menus, content etc. and displays the subpages in TXT mode when pressed Right or Left
- OK: Confirms user selections, holds the page (in TXT mode), views Channels menu (DTV mode)
- Back/Return: Returns to previous screen, previous menu, opens index page (in TXT mode). Quickly cycles between previous and current channels or sources
- My Button 1 (*)
- Netflix: Launches the Netflix application
- Rewind: Moves frames backwards in media such as movies
- Record: Records programmes**
- Colored Buttons: Follow the on-screen instructions for colored button functions
- Play: Starts to play selected media
- Pause: Pauses the media being played, starts time shift recording**
- Stop: Stops the media being played
- Fast Forward: Moves frames forward in media such as movies
- YouTube: Launches the YouTube application
- Prime Video: Launches the Amazon Prime Video application
- Exit: Closes and exits from displayed menus or returns to previous screen
- Info: Displays information about on-screen content, shows hidden information (reveal – in TXT mode)
- Menu: Displays TV menu
- Programme +/-
- Text: Displays teletext (where available), press again to superimpose the teletext over a normal broadcast picture (mix)
- Source: Shows available broadcast and content sources.
Footnote:
Red, green, blue and yellow buttons are multifunction; please follow on-screen
prompts and section instructions.
(**) If this feature is supported by your TV.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>