ADTRAn 1700341F1 NetVanta 3140 Fixed Port Router User Guide

NetVanta
Quick Start
NetVanta 3140 Fixed Port Router
March 2021 61700340F1-13D
P/N: 1700340F1 1700341F1

GETTING STARTED

This NetVanta unit ships with a statically assigned IP address of 10.10.10.1 and the ability to connect to a Dynamic Host Control Protocol (DHCP) network and receive an IP address assignment from a DHCP server. When connecting to a DHCP network, this unit supports Zero-Touch Provisioning, allowing the NetVanta router to download and apply configuration parameters from a configuration management server.

Regardless of the method you use to connect the NetVanta unit to the network, two configuration methods are available for your NetVanta unit:

• Web-based graphical user interface (GUI)
• ADTRAN Operating System (AOS) command line interface (CLI)

The GUI lets you configure the main unit settings and provides online guidance and explanations for each setting. However, using the AOS CLI may be necessary for more advanced configurations.

ACCESSING THE GUI

You can access the GUI from any web browser on your network in one of two ways:

Connecting via the Static IP Address

1. Connect the unit to your PC using the unit’s GIG 0/1 port and an Ethernet cable.

2. Set your PC to a fixed IP address of 10.10.10.2. To change your PC IP address, navigate to Computer > Control Panel > Network Connections > Local Area Connection > Properties > IP (TCP/IP) and select Use this IP Address. Enter these parameters:
   • IP Address: 10.10.10.2
   • Subnet Mask: 255.255.255.0
   • Default Gateway: 10.10.10.1
   You do not need to enter any domain naming system (DNS) server information. After the information is entered, select OK twice, and close the Network Connections dialog box. If you cannot change the PC’s IP address, you will need to change the unit’s IP address using the CLI. (Refer to t” Manually Configuring the Unit’s IP Address ” on page 2 for instructions.)

3. Open a web browser and enter the unit’s IP address in your browser address line as follows: http://10.10.10.1. The default IP address is 10.10.10.1, but if you had to change the unit’s IP address using the CLI, enter that address in the browser line.

4. You will then be prompted for the user name and password (the default settings are admin and password ).

5. The initial GUI screen appears. You can access initial setup information by selecting Setup Wizard from the menu on the left.

Connecting via the DHCP Client Address

1. Connect the router to an existing network that supports DHCP using the unit’s GIG 0/1 Gigabit Ethernet port. The NetVanta unit will automatically request an IP address assignment from the DHCP server.
2. Check the DHCP server and record the IP address assigned to the NetVanta unit.
3. Open a web browser on any network PC that can route to the IP address recorded in Step 2, and enter the NetVanta unit’s IP address.
4. The initial GUI screen appears. You can access initial setup information by selecting Setup Wizard from the menu on the left.

ACCESSING THE CLI

Access the AOS CLI via the CONSOLE port or a Telnet or SSH session. To establish a connection to the NetVanta unit CONSOLE port, you need the following items:

• PC with VT100 terminal emulation software.
• Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate interface for your terminal or PC communication port on the other end.

NOTE
There are many terminal emulation applications available on the web. PuTTy, SecureCRT, and HyperTerminal are a few examples.

1. Connect the DB-9 (male) connector of your serial cable to the unit’s CONSOLE port.

2. Connect the other end of the serial cable to the terminal or PC.
   NOTE
   Many PCs do not come with a standard serial port. A universal serial bus (USB) to serial adapter can be used instead. The drivers for the USB to serial adapter must be installed according to the manufacturer’s instructions. If the USB to serial adapter is not properly installed on your PC, you will not be able to communicate with the AOS unit and you should seek support from the USB to serial adapter manufacturer.

3. Provide power to the unit as appropriate. Refer to the NetVanta 3100 Series Hardware Installation Guide available online at https://supportcommunity.adtran.com for more details.

4. Once the unit is powered up, open a VT100 terminal session using the following settings: 9600 baud, 8 data bits, no parity bits, 1 stop bit, and no flow control. Press to activate the AOS CLI.

5. Enter enable at the > prompt and enter the Enable mode password when prompted. The default password is password.

You can also access the CLI from a Telnet or SSH client. In order to do this, you must know the IP address of the AOS device. If you do not know the unit’s IP address, you must use the CONSOLE port to access the CLI. To access the CLI using a Telnet or SSH client, follow these steps:

1. Connect the NetVanta unit to your PC using an Ethernet cable connected to the unit’s switch port labeled GIG 0/1, or connect the NetVanta unit to an existing network that supports DHCP using the unit’s GIG 0/ 1 switch port.
2. Open a Telnet or SSH client on your computer and enter 10.10.10.1. If your unit received an IP address from a DHCP server, or you have changed your unit’s IP address, you will need to enter that address instead.
3. For SSH, log into the unit using the default login (admin) and password (password). For Telnet, only the default password (password) is required.
4. Enter enable at the > prompt and enter the enable password when prompted. The default password is password.

COMMON CLI COMMANDS

The following are common CLI commands and tips for getting started with the CLI.

• Entering a question mark (?) shows contextual help and options. For example, entering ? at the prompt will show all commands available from that prompt.
• To view interface statistics, enter show interfaces .
• To view the current configuration, enter show running-config.
• To view all the IP Addresses currently configured, enter show ip interfaces brief.
• To view the AOS version, serial number, and other information, enter show version.
• To save the current configuration, enter write.

MANUALLY CONFIGURING THE UNIT’S IP ADDRESS

The following steps create an IP address (10.10.10.1 255.255.255.0) for Gigabit Ethernet port 0/1 (GIG 0/1). If you are not sure what IP address to assign, please contact your network administrator.

NOTE
This step is unnecessary if the unit’s IP address has been configured automatically using DHCP.

1. At the # prompt, enter config terminal.
2. At the (config)# prompt, enter interface gigabit-eth 0/1 to access the configuration parameters for the GIG 0/1 port.
3. Enter ip address 10.10.10.1 255.255.255.0 to assign an IP address to the GIG 0/1 port using a 24-bit subnet mask.
4. Enter no shutdown to activate the interface to pass data.
5. Enter exit to exit the Ethernet interface commands and return to the Global Configuration mode.
6. Enter ip route 0.0.0.0 0.0.0.0 10.10.10.254 to add a default route to the route table. 0.0.0.0 is the default route and the default subnet mask, and 10.10.10.254 is the next-hop IP address to which the AOS router should send all of its traffic. You will need to enter the proper route, subnet mask, and gateway for your network. This information is typically provided by a service provider or local network administrator.
7. Enter do write to save the current configuration.

NOTE
The configuration parameters used in the examples outlined in this document are for instructional purposes only. Please replace all underlined entries (example) with your specific parameters to configure your application.

CHANGING LOGIN PASSWORDS USING THE CLI

To change the login passwords for the NetVanta 3140, connect to the CLI and follow these steps:

1. To modify the user accounts and passwords, from the (config)# prompt, enter the command username password .
2. To modify the Enable mode password, from the (config)# prompt, enter the command enable password .
3. To modify the Telnet password, from the (config)# prompt, enter the command line telnet 0 4 and then press ENTER. Enter the command password .
4. Enter do write to save the current configuration.

FRONT PANEL LEDS

flashes rapidly for five seconds.
Green (solid)| The power is on and self-test passed.
Red (solid)| The power is on, but the self-test failed or the boot mode (if applicable) code could not be booted.
Amber (solid)| The unit is in bootstrap mode.
USB| Off| The interface is shut down or not connected.
Green (solid)| A supported device is connected.
Amber (flashing)| There is activity on the link.
Red (solid)| An alarm condition is occurring on the USB port, or there is a failure.
LINK
(GIG 1 -GIG 3)
(1700340F1 only)| Off| The port is administratively disabled or does not have link.
Green (solid)| The port is enabled and the link is up.
ACT
(GIG 1 – GIG 3) (1700340F1 only)| Off| There is no activity on the link.
Green (flashing)| There is activity on the link.
Port LEDs (GIG 0/1 –
GIG 0/3)| Off| There is no activity on the link.
Green (solid)| The port is enabled and the link is up.
Amber (flashing)| There is activity on the link.

NOTE
On the 1700341F1, the behavior of the LINK and ACT LEDs (labeled GIG 1 through GIG 3) on the front of the unit corresponds to the behavior of the RJ-45 LEDs (labeled GIG 0/1 through GIG 0/3) located on the back of the unit.

NETVANTA 3140 SERIES DEFAULTS

You can find more information regarding the default configuration of the NetVanta 3140 in the NetVanta 3140 Default Configuration article, available online at https://supportcommunity.adtran.com.

RESTORE FACTORY DEFAULTS

For information on restoring factory defaults, refer to the guide Restoring an AOS Device to Factory Default available online at https://supportcommunity.adtran.com.

CONFIGURE YOUR APPLICATION

The applications you will need to configure vary by product and by network. Review the list of defaults for your unit before deciding what applications to configure. At the end of this document is a list of configuration guides that relate to common applications that should be configured on startup. These guides are all available online on ADTRAN’s Support Community.

NOTE
Important: For additional details on product features, specifications, installation, and safety, refer to the NetVanta 3100 Series Hardware Installation Guide , available online at https://supportcommunity.adtran.com.

The following configuration guides provide configuration information for applications typically used within this product. All documents are available online at https://supportcommunity.adtran.com.
NetVanta 3100 Series Hardware Installation Guide
Configuring Port Forwarding in AOS
Configuring DHCP in AOS
Configuring VPN using Aggressive Mode in AOS
Configuring Internet Access (Many to one NAT) with the Firewall Wizard in AOS
Configuring QoS for VoIP in AOS
Configuring QoS in AOS
Configuring a VPN using Main Mode in AOS
Configuring WAN Failover with Network Monitor in AOS

Warranty: ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found online at www.adtran.com/warranty. Copyright ©2021 ADTRAN, Inc. All Rights Reserved.

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE OR DECREASE IN RELIABILITY HANDLING PRECAUTIONS REQUIRED

ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>