ADTRAn 854-6 Wi-Fi 6 2.5G Gateway Router User Guide

ADTRAN
September 2021
854-6/v6 Service Delivery Gateway
617600028F1-13A
Wi-Fi 6 2.5G Router
P/N: 17600026F1
17600028F1
Quick Start
Overview

WARNING!
Read all warnings, cautions, notes, and installation instructions before installing or servicing this equipment.

This document supports the following products:

This quick start describes how to install ADTRAN’s 854 service delivery gateways.
The 854-6 Wi-Fi 6 2.5G Router is an indoor gateway that performs like a true 2Gbps Router with Wi-Fi 6, delivering premium, multi-Gigabit services and Dual-band Wi-Fi 6. The 854-v6 Wi-Fi 6 2.5G Router offers the same features along with Voice services.

• “Installing the 854 Router” on page 2
• “Understanding the Status LEDs ” on page 4
  Figure 1 illustrates the front and back of the 854-v6 gateway. The 854-6 gateway does not offer voice connections (Tel1/Tel2).

WARNING indicates a hazard that, if not avoided, could result in death, injury, or serious property damage.| CAUTION indicates a hazard which, if not
avoided, could result in service interruption,
damage to the equipment, or minor property
damage.| NOTES inform the user of additional, but
important, information or features.

Features

The features of the 854 gateways include the following:

•  Combo WAN Uplink (one at a time)
  ♦ SFP cage
  ♦ 2.5GBASE-T (IEEE 802.3bz-2016)

• Subscriber Interfaces
  ♦ 4x Gigabit Ethernet (RJ-45) interfaces
  ♦ 4×4 802.11ax @ 2.4GHz
  ♦ 4×4 802.11ax @ 5GHz
  ♦ 1x USB 3.0 Type-A interface
  ♦ 2x voice (RJ-11) interfaces (854-v6 only)

Installing the 854 Router

The following are guidelines for the basic installation of the device.

NOTE
Refer to the national, state, and local electrical codes for the requirements for power, grounding, wiring, and installation methods.
CAUTION!
The product is intended for indoor use only. Ethernet, POTS cables, and attached equipment are intended for use within the same building with equipotential bonding and are not intended to be placed in separate buildings or structures. Failure to deploy as described could result in permanent damage from lightning or other electrical events and void the warranty. Furthermore, all connections from outside of the building, such as old POTSwiring, must be disconnected prior to use.

Package Contents

• ADTRAN’s 854-6 or 854-v6 WiFi 6 2.5G Router
• 12V DC power adapter

Prior to Installation
Before installing the equipment, inspect the gateway. If damage has occurred during shipping, file a claim with the carrier, and then contact ADTRAN Customer Support. For more information, refer to the product warranty available online at https://adtran/wp_support_warranty.
Required Tools
Standard technician tools and, if installing the gateway on a wall, a #2 Phillips-head screwdriver, are required for installing these devices.
Mounting Options
There are two options to install this device: desktop and wall mount. Be sure to route and secure the fiber and cables in a manner that will prevent damage. These options are described below.
Desktop Installation
This device can be placed on a desk or table. The following table shows the recommended minimum distance (in feet and meters) between ADTRAN equipment and household appliances to reduce interference.

Household Appliance| Recommended Minimum Distance (in feet and meters)
---|---
Microwave ovens| 30 feet / 9 meters
Baby monitor – analog| 20 feet / 6 meters
Baby monitor – digital| 40 feet / 12 meters
Cordless phone – analog| 20 feet / 6 meters
Cordless phone – digital| 30 feet / 9 meters
Bluetooth devices| 20 feet / 6 meters
ZigBee| 20 feet / 6 meters

WARNING!
Ensure that the device does not come in contact with water or other liquids.
CAUTION!
Ensure that the device is not located in direct sunlight or next to any thermal obstructions.

Wall Mount Installation
This device can be mounted on a wall. Wall Mount Kit (17600192F1) can be ordered for mounting the device. Instructions are provided in the related Quick Start Guide (617600192F1-13A).
Connecting the 854 Gateway
Figure 2 illustrates the installation (connection) options for this device.

The following subscriber connections are available on the rear of the device:

• 4x Gigabit Ethernet (RJ-45 Connectors) – LAN 1-4 ports
•  1x USB 3.0 (Type A Connector) – port
• 2x Telephone (RJ-11 Connectors) – Tel 1 and Tel 2 ports (854-v6 only)

To connect the subscriber interfaces, refer to Figure 2 and complete the following:

1.  For a WAN connection, do either of the following:
   ■ 2.5Gb WAN: insert a Cat 5E or better Ethernet cable into the port labeled 2.5G WAN until there is an audible “click”.
   ■ SFP WAN: insert a compatible SFP module into the SFP cage at the bottom of the Router..

2. For an Ethernet LAN connection, insert a Category 5E (or better) RJ-45 cable into one of the LAN ports (labeled LAN 1-4) until there is an audible “click”.

3. For a Voice connection on the 854-v6 only, insert an RJ-11 cable into one of the telephone ports (labeled Tel 1 or Tel 2) until there is an audible “click”.

4.  Before connecting to the service provider interface, clean the optical Interfaces of the SC/APC connectors.

5. Insert the fiber cable into the WAN port at the bottom of the gateway.

CAUTION!
To prevent breaking the fiber, do not exceed the fiber bend radius of 3.5 in (8.9 cm).

Connecting the Power Supply

1. Connect the end of the power adapter to the Power port on the rear panel of the gateway
2. Plug another end of the power adapter into the wall outlet.
3. Confirm that the power is connected properly. The Power LED should be lit on the front of the gateway.

NOTE
Alternately, the device may be powered by a supported third-party UPS which may be connected via a 7-pin Molex connector, labeled UPS.

Resetting the Gateway
A reset button is available if the device needs to be rebooted. To reboot the device, press the Reset button on the rear panel of the gateway for 5 seconds or less. To reset the device to custom defaults, press the Reset button for 5 seconds or more.

Understanding the Status LEDs

The LEDs on the back panel of the device enable you to monitor the device’s status. This section describes the four types of LEDs available on the gateway. See Figure 3 for details.

Fiber Status LED

The Fiber status LED indicates the state of an inserted Fiber SFP module.

PON.
Color| Off| The fiber-optic connection is DOWN.

2.5G WAN LED
The 2.5G WAN status LED indicates the state of the 2.5G WAN connection on the gateway.

1000/

100 Mbps

| Color| On| WAN is UP at 1000/100 Mbps speed.
| Flashing| WAN connection is transferring data.
| None| Off| The WAN connection is DOWN.

2.4GHz / 5GHz Status LEDs
The 2.4GHz and 5GHz status LEDs indicate the state of the wireless connections on the gateway.

WPS Status LED
The WPS status LED indicates the status of WPS (Wi-Fi protected setup).

Tel 1/2 Status LED (854-6 only)
The Tel 1/2 status LED indicates the state of the phone line ports on the 854-v6 device.

Product Specifications

Electrical
Power is provided by a 12V DC power adapter that is included with the device. The power adapter operates from a power source of 100 to 240V AC, 50 – 60 Hz. The nominal output is 12V DC +\–5% with a minimum current rating of 3.0 Amps. For US and Canadian applications, a UL Listed limited power source (LPS) is required. For deployment outside of North America, an LPS specifically approved for that country, such as a CE Mark, is required.
NOTE
It is strongly suggested that the power supply (a 5-foot (1.5 m) power cord) included with the 854-v6 be connected to a surge suppressor device that can have its own extension cable. The surge protection device should provide L-N, L-G, and N-G protection. It is also recommended that the device contains a visual ‘GOOD’ indicator.

Environment

• Operating Temperature: 32°F to 104°F (0°C to 40°C)
• Storage Temperature: -40°F to 158°F (-40°C to 70°C)
• Relative Humidity: 10 to 95 percent, non-condensing

NOTE
Changes or modifications not expressly approved by ADTRAN will void the warranty.

Safety and Regulatory

This product meets the following safety and regulatory requirements:

• UL/cUL Safety Listed
• IEC 62368-1
• EN 62368-1, AS/NZS 60950.1
• RoHS Compliant

This equipment contains no parts that can be serviced by the user.
Refer to the Safety and Regulator Notice for this product (P/N: 617600028F1-17) for detailed safety and regulatory information.

Documentation for ADTRAN Network Solutions products is available for viewing and download directly from the ADTRAN Support Community website.
Go to: https://supportcommunity.adtran.com
ADTRAN offers training courses on our products, including customized training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
Access additional safety information and product documentation using the QR code or website.

https://supportcommunity.adtran.com/

Warranty: ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks, registered trademarks, or trade names of their respective holders. Copyright © 2021 ADTRAN, Inc. All Rights Reserved.

Safety and Regulatory Notice

This document supports the following products:

WARNING!

• Read all warnings, cautions, notes, and installation instructions before installing or servicing this equipment.
•  Refer to the national, state, and local electrical codes for the requirements for power, grounding, wiring, and installation methods.
• This product may be powered by multiple sources. Disconnect all sources of power prior to servicing.

CAUTION!

• Connect the DC power inputs to an approved Limited Power Source (LPS) power supply ONLY.
• This equipment contains no parts that can be serviced by the user.
• This product is intended to operate in ambient temperatures up to 40°C.
• It is recommended that an external AC Surge Protection Device be installed at the AC input connection to the local AC-Powered product. The Surge Protection device should provide L-N, L-G, and N-G protection. It is also recommended that the device contains a visual ‘GOOD’ indicator.
• The product is intended for indoor use only. Ethernet, Voice, and attached equipment are intended for use within the same building with equipotential bonding, and not intended to be placed in separate buildings or structures. Failure to deploy as described could result in permanent damage from lightning or other electrical events and voids the warranty.

NOTES
This product meets the following compliance requirements:

• This equipment contains no parts that can be serviced by the user.
• This product meets the EU RoHS Directive. Refer to www.adtran.com/environmental for further information on RoHS/WEEE.
• This product is UL Listed to the applicable UL/CSA Standards.
• This product has also been evaluated to applicable international standards including CE and RCM marking.
• The AC branch circuit socket-outlet must be installed near the equipment and must be easily accessible.
• The RJ-45 jacks are not used for telephone line connections.

This radio transmitter (IC: 2250A-W649A) has been approved by Industry Canada to operate with the antenna types listed below. Antenna types not included in this list are strictly prohibited for use with this device.

• Dynamic Frequency Selection (DFS) for devices operating in the bands 5250 – 5350 MHz, 5470 – 5600 MHz, and 5650 – 5725 MHz.
• The device for the band 5150-5250 MHz is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems.
• Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650- 5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
• The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the equivalent isotropically radiated power (EIRP). limit.
• The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the EIRP limits specified for point-to-point and non-point-to-point operation as appropriate.
  This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s).
  Operation is subject to the following two conditions:
  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

Regulatory Compliance Information

This section includes user requirements for operating this product in accordance with National laws for the usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable National regulatory authority.
This product’s firmware limits operation to only the channels allowed in a particular Region or Country. Therefore, all options described in this user’s guide may not be available in your version of the product.
Europe – EU Declaration of Conformity
Products bearing the marking comply with the following EU directives:

•  EMC Directive 2014/30/EU
• Low Voltage Directive 2014/35/EU
• WEEE Directive reference: 2012/19/EU

If this product has telecommunications functionality, it also complies with the requirements of the following EU Directive:

• RED 2014/53/EU
  Compliance with these directives implies conformity to harmonized European standards that are noted in the EU Declaration of Conformity.
  For indoor use only. Valid in all EU member states, EFTA states, and Switzerland.
  This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information, the end-user should contact the national spectrum authority in France.

FCC Requirements for Operation in the United States

FCC Information to User
This product does not contain any user-serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals.
FCC Guidelines for Human Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 26 cm between the radiator and your body.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
FCC Declaration of Conformity
We, ADTRAN, Inc., 901 Explorer Blvd, Huntsville, AL 35806, declare under our sole responsibility that this device complies with Part 15 Subpart B of FCC CFR47 Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation.

FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAN ICES-3(B)/NMB-3(B)
Canadian Department of Communications Radio Interference Regulations This digital apparatus (Wi-Fi 6 2.5G Router Model 854-v6) does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
Industry Canada
This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE: Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 31cm between the radiator & your body.
CAUTION!
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
(iii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and
(iv) the worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2(3) shall be clearly indicated.
(v) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 56505850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.

Installation Instructions:
Refer to the Quick Start or Job Aid for this product (P/N: 617600028F1-13) for detailed installation instructions.

ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807

Copyright © 2021 ADTRAN, Inc. All Rights Reserved.

References

• Training
• Environmental
• Training
• My Adtran Log In
• Warranty Information
• Home - Adtran Support Community

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>