LUXUL P40 AC1200 WiFi Bridge + Range Extender Installation Guide

QUICK INSTALL GUIDE

AC1200 WiFi Bridge + Range Extender P40
Includes: P40 Wireless Range Extender

READ ME FIRST

INSTALLATION AND SETUP

1. Introduction and Safety Information
The compact design, allows you to install the P40 everywhere and still provide excellent network performance to extend the Wi-Fi signal and wireless coverage. This P40 is designed for indoor use only. DO NOT expose this device to direct sunlight, rain, or snow.

Caution: DO NOT put the P40 in or near hot or humid places, like the kitchen or bathroom. Also, do not leave the P40 in the car during the summer.
The P40 will become hot when being used for a long time (this is normal and is not a malfunction). DO NOT put the P40 on paper, cloth, or other fl flammable objects.

Difference between client/repeater mode:

In Client Mode , your P40 will act as a client, connecting wirelessly to your existing wireless network. You can then connect physically through the Ethernet port on the bottom
of the P40 to whatever device you want to provide internet connectivity to.
In Repeater Mode , your P40 will act as an access point, rebroadcasting your wireless signal from the next closest AP.

**Access and Setup for Repeater Mode:

**

The switch on the bottom of the P40 should be on “Repeater.”
The P40 setup can be initiated two ways; choose the one below that works best for you:
Option 1: Open an Internet Browser. Using your OS settings, connect to a wireless network called “repeater. setup” (no password required).
Option 2: Open an Internet Browser. Connect an Ethernet cable from your device to the Ethernet port on the P40.
After performing either Option 1 or 2, a login window will open in your Internet Browser to start the setup of the P40. The  default username and password are both “admin.”

Default IP: 192.168.1.1
Username: admin
Password: admin

After logging in, click “Continue” to start the setup wizard or you can click “Skip Wizard” to see the main menu.
After clicking “Continue,” the P40 will scan for and display a list of the wireless networks (SSIDs) it can see. Select yours, then click “Continue.” If you don’t see your network, you can click “Refresh” to refresh the list.
You will be prompted to enter a password for that wireless network (SSID). Enter the exact same password you use for that existing wireless network (SSID). It is case-sensitive. Click “Continue.”
When setting the P40 up in Repeater Mode, you will be asked if you would like to extend a second network on another frequency. This is so you can extend both 2.4GHz and 5GHz networks for better coverage. This page will not show up if you are using the P40 as a bridge client. Select “Yes” or “No” and follow the steps past the password again.

You will be asked if you want to use the same wireless name (SSID) as the one you’re extending or if you want to customize the wireless name (SSID) you want the P40 to broadcast. Make your selection and then click “Continue.”

Note: Changing the network name (SSID) does not aspect how the P40 connects to your current wireless network, and you will not see this page when setting up the P40 in Client Mode.

You will be asked to change the admin password for accessing the user interface of the P40.
Change that, and click “Continue.” You will then be asked if you want the LEDs on or of. Make your choice, and click “Continue.”
After 60 seconds, you will lose access to that page, and your P40 should be ready. You can then move it to where you would like it to be.

Access and Setup for Client Mode

Flip the switch on the bottom of the P40 to “Client.” c Caution: Moving this switch will set the P40 back to factory default.
The P40 setup can be initiated two ways; choose the one below that works best for you:
Option 1: Open an Internet Browser. Using your OS settings, connect to a wireless network called “repeater. setup” (no password required).
Option 2: Open an Internet Browser. Connect an Ethernet cable from your device to the Ethernet port on the P40.
After performing either Option 1 or 2, a login window will open in your Internet Browser to start the setup of the P40. The default username and password are both “admin.”

Default IP: 192.168.1.1
Username: admin
Password: admin

After logging in, click “Continue” to start the setup wizard or you can click “Skip Wizard” to see the main menu.
After clicking “Continue,” the P40 will scan for and display a list of the wireless networks (SSIDs) it can see. Select yours, then click “Continue.” If you don’t see your network, you can click “Refresh” to refresh the list.

You will be prompted to enter a password for that wireless network (SSID). Enter the exact same password you use for that existing wireless network (SSID). It is case-sensitive. Click “Continue.”
Next, you will be asked to change the admin password for accessing the P40 user interface. Change that, and click “Continue.”
You will then be asked if you want the LEDs on or off. Make your choice, and click “Continue.”
In Client Mode, the P40 will not broadcast any SSIDs; you will use the Ethernet port to connect a device.

Note: When done setting the P40 up in Client Mode, you should have internet access through the Ethernet port on the P40.

Hardware Description

Front & Bottom Panels
The front of the P40 includes fi ve link/activity LEDs, one power  LED, and a LEDs/Reset button; the bottom has the mode sector and Ethernet port. For more information on these LEDs, refer to the table describing these indicators in the next section.

P40 front panel view

P40 bottom view

LEDs/Reset

LED Indicators
The front panel of the P40 includes fi ve link/activity LEDs and one power LED. For more information on these LEDs, refer to the table describing these indicators below.

LED| Color| Status|

Description

---|---|---|---

5G

|

Amber

| Steady On| Good signal reception
Blinking| Normal signal reception: slow blinking (RSSI <50%-25%)
Poor signal reception: quick blinking (RSSI <25%)
Off| No signal or LED off mode
2.4G|

Green

| Steady On| Good signal reception
Blinking| Normal signal reception: slow blinking (RSSI <50%-25%)
Poor signal reception: quick blinking (RSSI <25%)
Off| No signal or LED off mode
LAN| Green| Steady On| LAN port is connected
---|---|---|---
Blinking| LAN port is active (transferring or receiving data)
Off| LAN port is not connected or LED off mode
Client| Green| Steady On| P40 is in Client Mode
Repeater| Green| Steady On| P40 is in Repeater Mode
PWR| Green| Steady On| The power is turned on. When the device is in LED off mode, even when the device is powered on, all LEDs will be off, including power LED
Slow Blinking| Performing a “reset to factory default”
Off| Power is turned off

LED/Reset Button
To turn the LEDs on or off, press and release the “LEDs/Reset” button once. To reset the Range Extender, press and hold the “LEDs/Reset” button for 5 seconds (“PWR” LED will blink after 5 seconds), then release.

P40 Placement

Placing the P40 is similar to placing any wireless access point. Please refer to this support page for details about wireless AP placement: https://www.luxul.com/support/ap-placement.aspx

801-822-5450
E: sales@luxul.com| E: support@luxul.com

Copyright and Trademark Notices:

No part of this document may be modifi ed or adapted in any way, for any purposes without the permission in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design. No license is granted, either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in this or any Luxul product.

© Copyright 2018 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and registered trademarks are property of their respective holders.
LUX-QIG-P40-v4 06251804

A brand of Legrand

Documents / Resources

| LUXUL P40 AC1200 WiFi Bridge + Range Extender [pdf] Installation Guide
P40, AC1200 WiFi Bridge Range Extender
---|---
| LUXUL P40 AC1200 WiFi Bridge Range Extender [pdf] Installation Guide
P40 AC1200 WiFi Bridge Range Extender, P40, AC1200 WiFi Bridge Range Extender, WiFi Bridge Range Extender, Bridge Range Extender, Range Extender, Extender

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>