LUXUL XMS-2624P Managed POE Switch User Guide

LUXUL XMS-2624P Managed POE Switch

1. Setting up your Switch:
   Place your switch in a rack or on a desktop

2. Connect one Ethernet cable from your router or other switch to any port on the switch. Connect the included power cable from your switch to your power source.
   NOTE : Your switches boot time will be a minimum of 60 seconds.

3. The default IP address method for your switch is via DHCP with a fixed failover of 192.168.0.4. Please locate your switch IP address using your Router’s Connected Client list or similar function. Using the IP address that you find there, login with the default credentials.
   User Name: admin
   Password: admin
   NOTE : If your computer or device isn’t set to obtain an IP address automatically, you’ll need to set a temporary static IP address on that device. Set the IP address of your computer to an address in the 192.168.0.X range and set your subnet mask to 255.255.255.0. You can leave the default gateway/router IP address blank.

What if…

I need to restore factory default settings?

If you wish to factory default the switch, hold the button labeled ‘MODE/RESET’ for longer than 7 seconds. The switch will reboot once the button is released. Reboot will take approximately 60 seconds before the UI becomes available. If a DHCP server is not available the Failover IP will become active 60 seconds after the boot completes.

I need to restart my switch?
To restart your switch, unplug the power cable or hold the button labeled ‘MODE/RESET’ for 2-7 seconds, or use the Reboot function in the Administration tab in the UI.

I want to perform advanced configuration?
The default IP address method for your switch is via DHCP with a fixed failover of 192.168.0.4. Please locate your switch IP address using your Router’s Connected Client list or similar function. Using the IP address that you find there, login with the default credentials.
NOTE : Changes made to the switch’s configuration must be save or they will be lost upon switch reboot. Go to Administration> Configuration>Save startup-config and Save Configuration.

FAQ

We have prepared a list of items to help you best understand the new features with these models and how to best plan and execute systems that feature them.To see our FAQs, visit the “Resources & Tools” section at the bottom of your switches product page on legrandav.com/luxul.

Product Descriptions

• SW-510-48P-F 48 PoE+ Ports with (4) Gigabit SFP Ports Managed Gigabit Switch
• SW-610-48P-F 48 PoE+ Ports with (4) 10 Gigabit SFP+ Ports Managed Gigabit Switch

View Luxul’s Privacy policy at:
https://www.legrandav.com/legal/privacy_policy
The marking information is located at the bottom of the apparatus

Copyright and Trademark Notices

No part of this document may be modified or adapted in any way, for any purposes without permission in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design. No license is granted, either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license only exists for equipment, circuits and subsystems contained in this or any Luxul product.

© Copyright 2021 Legrand AV Inc. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and Simply Connected are all trademarks and or registered trademarks of Legrand AV Inc. All other trademarks and registered trademarks are property of their respective holders.

What do the LEDs on my switch indicate?

Ethernet Port

PoE Status*

| Green| Switch providing PoE power to connected device
Amber| PoE power limit exceeded
Blinking| PoE fault error
Off| No PoE device connected
SFP Port Status| Green| 1Gbps connection
Blue**| 10Gbps connection

• Quickly press and release the ‘MODE /RESET’ button to switch the LEDs between ‘LINK/ACT’ and ‘PoE’ status
  ** Applies only to the SW-610-XX models

PoE power budget
Do not exceed the PoE budget for your model shown in the table below

This equipment is not suitable for use in locations where children are likely to be present.
NOTE : This device is intended for indoor use only. All Ethernet cables are designed for intra-building connection to other equipment. Do not connect these ports directly to communication wiring or other wiring that exits the building where the appliance is located.

Technical Support
P: 801-822-5450
Email: support@luxul.com
Support chat: LegrandAV.com click ‘Live Chat’ (upper right) and select Luxul under ‘Brand’.

Sales
Phone:801-822-5450
Emaail:sales@luxul.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>