Telit WE310F5-I/P Evaluation Board User Guide

WE310F5-I/P
Quick Setup Guide
1VV0301671 Rev. 7 ­ 2021-07-16

Telit Technical Documentation

Program the WE310F5 Module

1. Connect the micro-USB UART1 port to your system.

2. Change the toggle switch position to Program.

3. Download and unzip the Telit_Wifi_Image_Tool.
   For download information, see Resource Links.

4. Open the Telit_Wifi_Image _ Tool folder.

5. Open the Telit_Wifi_Image_Tool application.

6. Click Browse.

7. Navigate to the Telit_Wifi_Image_Tool and select s2w.bin file.

8. To initiate the flash, click Program.

9. After the flash process is complete, click OK.

10. Close the Telit_Wifi_Image_Tool.
    The WE310F5 EVB is ready to configure.

Configure the WE310F5 Module

1. Connect the micro-USB cable to the UART0 port.
2. Change the toggle switch position to Run.
3. Open Tera Term > Setup > Serial Port.
4. Set the BAUD rate. The WE310F5 EVB is ready to use.

Prerequisites:

• Ensure to connect the module and the node to the same WPA2 Secured Wi-Fi network.
• Insert the SIM card in the appropriate SIM card slot.

Wireless Mode- Station Mode

1. To set the module in Station Mode: AT+WNI=0.
2. To connect the network to L3:
3. AT+WNCN=1,”Telit_WiFi”,”Password123″,11

Wireless Mode- AP Mode

1. To set the module in AP Mode: AT+WNI=1.

2. To configure the IP:
   AT+WNIPC=0,1,192.168.5.1,255.255.255.0,192.168.5.1

3. To configure the node in AP Mode:
   AT+WNAPIPC=0,192.168.5.3,192.168.5.20,86400000

Bluetooth Mode- Station Mode

1. To scan the available Bluetooth devices: AT+BI=1.
2. For DUT peripheral connection:
   Device 1
   AT&W0
   AT+YSR
   AT+BI=1
   AT+BICAP=0
   AT+BADVINTMIN=60
   AT+BADVINTMAX=60
   AT+BADVE=1
   AT+BATTRIB=”pserv”,”uuid=1234″
   AT+BATTRIB=”char”,”prop=0x0c”,”uuid=5678″
   AT+BATTRIB=”charval”,”perm=0011″,”len=1″,”val=0x30″
   AT+BATTRIB=”complete”
   AT+BOAD
   AT+BI=1
   AT+BCONINTMAX=1000
   AT+BCONINTMIN=1000
   AT+BCONNECT=”00217E368’22”,”t2″

WE310F5 Products

WE310F5-I
WE310F5-P
WE310F5 Callouts

W-I WE310F5-I Antenna Connector
W-P WE310F5-P RF Pad
1 UART (PL608)
2 I2S-I2C (PL601)
3 GPIO – Alternate Function (PL302 – PL305)
4 General Purpose Button (PB1-PB2) 5 Reset Button
6 RUN/ PROGRAM Toggle Switch
7 Audio Jack
8 Power Switch- Module
9 PB1-PB2 (PL605)| 10 ARDUINO Enable (PL705)
11 UART1
12 GPIO- LED (PL606)
13 UART0
14 Power Switch- EVB
15 Power connector USB 2.0
16 Power Config (PL201-P204)
17 SWD
18 SPI-SDIO (PL604)
19 LED
---|---

Resource Links:

• Telit_Wifi_Image_Tool ­
  https://www.telit.com/wpcontent/uploads/2021/06/Telit_WE310F5_39.00.001-1.zip
  For latest Firmware version, visit https://www.telit.com/support-training /download-zone/
  For more information, visit https://www.telit.com/products/wifi-and- bluetooth/#wifi

• For technical support, email us at TS-SRD@telit.com

• For a video demonstration, see https://www.telit.com/developerzone/we310f5-i-p-evb/?

The Telit EVB is a rapid loT development kit that reduces the duration of loT prototyping cycles from a matter of weeks or months to mere hours, all by capitalizing on the combination of embedded lot software and hardware.
The system was designed to provide a complete development environment to the user and intended for use with the Telit WE310F5-I/P module and
Arduino Uno Rev3 board.

Copyright © 2021 Telit. All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>