Telit WE310G4-I/P Dual Band WiFi and Bluetooth Low Energy Module User Guide

Telit WE310G4-I/P Dual Band WiFi and Bluetooth Low Energy Module

Program the WE310G4 Module

1. Connect the micro-USB UART1 port to your system.
2. Change the toggle switch position to Program.
3. Download and unzip the Telit_Wifi_Image_Tool. For download information, see Resource Links.
4. Open the Telit_Wifi_Image_Tool folder.
5. Open the Telit_Wifi_Image_Tool application.
6. Click Browse.
7. Navigate to the Telit_Wifi_Image_Tool and select s2w.bin file.
8. To initiate the flash, click Program.
9. After the flash process is complete, click OK.
10. Close the Telit_Wifi_Image_Tool.
    The WE310G4 EVB is ready to configure.

Configure the WE310G4 Module

1.  Connect the micro-USB cable to the UARTO port.
2. Change the toggle switch position to Run.
3. Open Tera Term Setup Serial Port.
4. Set the BAUD rate.
   The WE310G4 EVB is ready to use.

Wireless Mode- Station Mode

1. To set the module in Station Mode: AT+WN I=0
2. To connect the network to L3: AT+WNCN=l, “Telit_WiFi”, “Password123”, 11

Wireless Mode- AP Mode

1. To set the module in AP Mode: AT+WNI=1
2. To configure the IP: AT+WNI PC=0, 1,192 .168.5.1,255.255.255.0,192.168 .5.1
3. To configure the node in AP Mode:AT+WNAPIPC=0, 192.168.5.3,192.168.5.20, 86400000

Bluetooth Mode- Station Mode

1. To scan the available Bluetooth devices: AT+BI=1
2. For DUT peripheral connection:
   • Device
   • AT&WO
   • AT+YSR
   • AT+BI=1
   • AT+BICAP=0
   • AT+BADVINTMIN=60
   • AT+BADVINTMAX=60
   • AT+BADVE=1
   • AT+BATTRIB=”pserv”, “uuid=1234”
   • AT+BATTRIB=”char”, “prop=0x0c”, “uuid=5678”
   • AT+BATTRIB=”charval”, “perm=0011”, “len=1”, “val=0
   • X30″
   • AT+BATTRIB=” complete”
   • AT+BOAD
   • AT+BI=1
   • AT+BCONINTMAX=1000
   • AT+BCONINTMIN=1000
   • AT+BCONNECT=”00217E3 68’22”, “t2”

WE310G4-I

WE310G4-P

WE310G4 CalIouts

W-I WE310G4-1 Antenna Connector
w-P WE310G4-P RF Pad

1. UART (PL608)
2. 12S-12C (PL601)
3. GPIO Alternate Function (PL302 PL305)
4. General Purpose Button (PB1-PB2
5. Reset Button
6. RUN/ PROGRAM Toggle Switch
7. Audio Jack
8. Power Switch- Module
9. PB1-PB2 (PL605)
10. ARDUIN0 Enable [PL705)
11. UART1
12. GPIO-LED (PL606)
13. UARTO
14. Power Switch- EVB
15. Power connector USB 2.0
16. Power Config (PL201-P204)
17. SWD
18. SPI-SDIO IPL604)
19. LED

Resource Links:

• Telit Wi-Fi Image Tool and new FW releases [Login Required), visit https://www.telit.com/support-tools/download-zone/
• For more information, visit https://www.telit.com/modules-overview/wifi-and-bluetooth/
• For technical support, email us at TS-SRDatelit.com
• For a video demonstration, see https://www.telit.com/devices/we310g4/

References

• WE310G4 Is a Dual-Band Wi-Fi and Bluetooth® Low Energy Module
• Low-Energy Wi-Fi and Bluetooth® Embedded Modules | Telit

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>