BOSS PHANTOM900 Bluetooth Weather Rated Chrome Speaker User Manual
- June 6, 2024
- Boss
Table of Contents
BOSS PHANTOM900 Bluetooth Weather Rated Chrome Speaker
What Is In The Box
Phantom900 speakers w/clamps …………………………… 2 pcs
Mounting inserts:
1″ diameter (installed) ……………………………………………. 4 pcs
1.25 ” diameter ……………………………………………………….. 4 pcs
1.5 ” diameter ………………………………………………………….. 4 pcs
5mm Hex wrench ………………………………………………….. 1 pc
6mm Hex wrench ………………………………………………….. 1 pc
Features
Your new Phantom900 speakers feature the following:
- 3.5mm audio input
- Adjustable speaker clamps
- Weatherproof volume control
- Weatherproof speakers
- Bluetooth audio streaming
- Built-in class D amplifier
Installation
- Adjust the direction of the speaker and screw the bracket to the bottom of the speaker.
- Select the rubber inserts that fit your mounting bar and place them into the brackets.
- Find a safe, ideal mounting location and fit the clamps over the chosen bars.
- Fasten the mounting screws after you review the safety of the mounting location.
Reminder
- The components and wiring should not be installed around any moving parts, keep away from ignition parts, fuel lines, or any hot exhaust components.
- Speakers should not be installed where they might inhibit safety features on the vehicle ( i.e. lights, horns, brake levers, etc.).
Power Supply Connection
Option A
Connected to Battery through a
12 VDC SPDT Relay
(Single Pole Double Throw)
NOT INCLUDED, SOLD SEPARATELY
Option B
Connected to Battery through a
Waterproof Switch (250V AC/6A)
NOT INCLUDED, SOLD SEPAR ATELY
Note:
- AUX 3.5 female input connector for output of other audio device like mobile phone, MP3, iPod and so on.
- Should use standard 3.5mm 3-pole male plug AUX cable (not included).
- Stop BT connection first when using the 3.5mm AUX input as an audio source input.
Option A (Relay)
Option B (Switch)
Wiring
- Be sure to run the wiring securely and far away from any moving components.
- Connect the power cable to the power source. You will need to connect the 12V red wire to a fused7.5A (not included) switched power source.
- Use the 3.5mm stereo jack to connect to your source of music (MP3 player, mobile device, etc.).
- Use your player device and wired remote volume controller to control the volume.
Bluetooth Connection
- Go into the Settings Menu of your mobile device.
- Enter the Bluetooth menu.
- Search for and select ” Boss Audio Phantom ” from the available devices.
- If prompted, enter passcode “0000”.
Specifications
| Signal-to-Noise | > 75 dB |
|---|---|
| Channel separation: | > 50 dB |
| Frequency response: | 50Hz – 20 KHz |
| Input sensitivity: | Max 400 mv |
| Speaker wires: | 3.3′ |
| Volume control wires: | 4.9′ |
| Audio input cable: | 0.8′ |
| Power cable: | 3.3′ |
| Mounting diameter: | 1″, 1.25″, 1.5″ only |
| Dimensions: HxDxW | – 11.46″ x 6.38″ x 4.77″ |
| Unit weight: | 5.22Ibs / 2.37 kg |
Total Harmonic Distortion < 0.1%
Specification subject to change without notice.
Trouble shooting
SYMPTOM SOLUTION
No sound———————————— Unit or Device is MUTED
Audio is distorted————————- Bluetooth is out of range
No Power-on tone—————————– Check fuse or wiring
Bluetooth not connecting————- Switch off power for 10 secs
BOSS Audio S stems
3451 Lunar Court • Oxnard, CA 93030 www.bossaudio.com
805-751-4853 Customer Service
Tech Support: www.bossaudio.com/su port
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>