MrSafe Wireless Kinetic Doorbell KB-333 User Manual
- June 6, 2024
- mrSafe
Table of Contents
MrSafe Wireless Kinetic Doorbell KB-333
CONTENT OF PACKAGING
Kinetic push button + 230V Receiver + Mobile Receiver + Industrial tape +
Screws + Plugs
PARTS & BUTTONS
1. Kinetic Push Button
A: Doorbell button
2. 230V Receiver
B: Power Plug
C: Tone selection button
D: Volume button
3. Mobile Receiver
E: ON/OFF switch
F: Battery Compartment G: Tone selection button H: Volume button
INSTALLING AND PAIRING THE KINETIC PUSH BUTTON
You can attach the Kinetic Push Button to any surface using the supplied industrial tape and screws. Take the plastic plate with the 2 screw holes and hold it against the wall you wish to attach it to. By using a pencil, indicate where you need to drill the holes. Drill 2 holes where the indication is visible. Insert 2 plugs into the holes, place the plastic plate in the correct location and screw it in place. To finish, put one side of the the Industrial tape on the plastic plate and stick the Push Button on the other side. You can pair multiple push buttons (optionally available on www.mrsafe.eu) with the receivers.
INSTALLING AND PAIRING THE 230V RECEIVER
You can plug the 230V Receiver into any socket in your house, the pairing for
your set has already been done during production.
To pair an extra 230V Receiver with your Push Button (optionally available on
www.mrsafe.eu), put the Receiver into a power socket to turn it on, the
receiver is now in pairing mode for 2 minutes. Press the Doorbell button (A)
once. You will hear a sound notification and see a red light on the 230V
Receiver to indicate that your devices are paired.
Up to 8 Push Buttons can be saved on one receiver. If you attempt to add a
ninth, the first one will be deleted. 1 Push Button can be connected to an
unlimited number of receivers.
INSTALLING AND PAIRING THE MOBILE RECEIVER
Before installing the Mobile Receiver, insert 3x AA Alkaline batteries into
the Battery Compartment (F). Open the cover of the battery compartment. Insert
3 AA Alkaline batteries according to the visible scheme and close the cover.
You can take the Mobile Receiver anywhere in your house (up to 100 m), the
pairing for your set has already been done during production.
To pair an extra Mobile Receiver with your Push Button (optionally available
on www.mrsafe.eu), you should turn on the Mobile Receiver by sliding the
ON/OFF switch (E) in the ON position, the Mobile Receiver is now in pairing
mode for 2 minutes. Press the Doorbell button (A) once. You will hear a sound
notification and see a red light on the Mobile Receiver to indicate that your
devices are paired. Up to 8 Push Buttons can be saved on one receiver. If you
attempt to add a ninth, the first one will be deleted. 1 Push Button can be
connected to an unlimited number of receivers.
SELECTING A RINGTONE AND ADJUSTING THE VOLUME
To select a ringtone on either the 230V Receiver or the Mobile Receiver, press
the Tone selection button of the device (C, G) until you hear the ringtone you
wish to select.
Note : If you wish to have the same ringtone on both devices, you have to
set it for each device separately. Note: When multiple Kinetic Push Buttons
are paired to your device, it is not possible to have a separate sound for
each Push Button. To adjust the volume on either the 230V Receiver or the
Mobile Receiver, first, press the Tone selection button of the device (C, G)
to hear a tune and press the Volume button of the device (D, H) to select the
desired volume.
SUPPORT
For more information, technical questions and return requests concerning this
product, you should contact support@mrsafe.eu.
WARRANTY
Mr Safe is a registered trademark of TE-Group NV. The mr Safe brand stands for superior product quality and outstanding customer service. That is why mr Safe warrants this product against all defects in material and workmanship for a period of two (2) years from the date of original purchase of the product. The conditions of this guarantee and the extent of responsibility of mr Safe under this guarantee can be downloaded from our website: www.mrsafe.eu.
DECLARATION OF CONFORMITY
Hereby,
| Company/Enterprise: | TE-Group NV |
|---|---|
| Address: / Adresse: | Kapelsestraat 61, 2950 Kapellen, Belgium |
| Product name: | mr Safe KB-333 |
| --- | --- |
| Product type: | Wireless Kinetic Doorbell Set |
conforms with the following safety requirements of the directives 2011/65/EU, 2014/53/EU & 2015/863/EU. Conformity is guaranteed by the CE-symbol. This product has been tested against following standards and specifications. The full text of the EU declaration of conformity is available at the following internet address: http://www.mrsafe.be/DOC_KB-333.
ILLUSTRATIONS
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>