mrsafe AP-300 Portable Air Purifier User Manual

June 5, 2024
mrSafe

mrsafe AP-300 Portable Air Purifier

PARTS & FUNCTIONS

See illustration I

  1. Air outlet
  2. Operation panel
    • A. Power button
    • B. Speed button
    • C. Timer button
    • D. Light/Child lock button
    • E. Anion/Filter button
  3. Light box
  4. Air quality sensor
  5. Air inlet
  6. Filter
  7. Back cover

INSTALLATION

See illustration II

The air purifier has a filter installed.
To remove and replace the filter, please follow these steps:

  1. Press the button at the back of the unit to remove the back cover (7).
  2. Take out the filter from the inside of the air purifier.
  3. Take the replacement filter and remove the plastic bag.
  4. Install the replacement filter without the plastic bag into the air purifier. The bottom part of the filter compartment should be pressed down a bit while installing the filter. Note: The closed side of the filter shall face toward the base.
  5. Press the button on the back cover (7) to put the back cover back on the unit.

Important:

  • When replacing the filter, please turn off the power first. Do not operate with the filter removed (no dust removal effect, and the dust that is inhaled may cause equipment failure).

  • Place the filter in a ventilated place so that the harmful gases and bacteria on the surface of the filter can be
    volatilized. Do not expose it to excessive sunlight.

  • Do not wash the filter with water.

OPERATION

  1. After plugging in the power, all indicators will light for 1 sec. and turn off again. The air purifier is now in standby mode.

  2. Press the Power button (A) to start the air purifier in default automatic operation mode (see below for more information). You will hear a sound indicating that the device is ON.

  3. The light box (3) will light in different colors for about 30 sec. during preheating of the sensor. After the sensor is
    preheated, the air quality indication is displayed and the light box will light in the color of the current air quality:

    • Good quality: Blue color
    • Medium quality: Yellow color
    • Bad quality: Red color
  4. Press the power button (A) to turn off the device. All indicators will turn off. The air purifier is now in standby mode.

  • TIMER
    Press the Timer button (C) to display a cycle of 2 – 4 – 8 hours on the display and make your selection. Each time you press the button, you will hear a sound and the corresponding indicator will light. When the set time is up, the air purifier will turn off and return to Standby mode.

  • SPEED
    Press the Speed button (B) to change the working speed of the air purifier: AUTO (automatic) – H (high speed) – M (medium speed) – L (low speed – sleep mode). The selected speed mode indicator will turn ON.
    When the air purifier operates in automatic mode the speed will be adjusted automatically according to the amount of particles in the air. If the air quality sensor measures a value:

    • between 1-75 (PM2.5 value) the blue color will be displayed and the unit will operate in lowest speed.
    • between 76-150 (PM2.5 value) the yellow color will be displayed and the unit will operate in middle speed.
    • between 151-999 (PM2.5 value) the red color will be displayed and the unit will operate in highest speed.
  • SLEEP MODE
    When the air purifier works in sleep mode (lowest speed mode), the “Moon” indicator will light. If there is no operation for 5 sec., the power and sleep mode indicator will be ON in low brightness and all other lights will turn off. The air purifier now operates in low noise mode. Press the Speed button (B) to exit the sleep mode and select another speed mode.

  • LIGHTING MODE
    Press the Light button (D) several times to select the desired lighting mode: Soft – Standard – Off. Each time you press the button, you will hear a sound.

  • CHILD LOCK
    Press the Child Lock button (D) for 3 sec. No function can be operated in this mode. When activated, the Child Lock indicator is ON. To unlock, press the Child Lock button (D) again for 3 sec.

  • ANION FUNCTION
    Press the Anion/Filter button (E) to activate the Anion function. Press again to deactivate the function.

  • FILTER REPLACEMENT REMINDER
    The HEPA + activated carbon composite filter inside the air purifier needs to be replaced every 3 months (2200 hours). When the filter replacement reminder (E) flashes red, it means that the filter needs to be replaced. Replace the filter as described above and press and hold the filter replacement button to reset the filter replacement cycle.
    Note: Depending on the place and the method of use (for example, households with a large number of smokers or areas with severe air pollution), the filter replacement cycle may be shortened. If the filtration effect is not obvious, replace the filter in time.

SAFETY INSTRUCTIONS

  1. Do not place in the following places:
    • In direct sunlight or facing the air outlet and heated places.
    • Close to devices such as TVs and radios (which may cause image distortion and noise). Please place it at a distance of 1m or more.
  2. In order to effectively circulate the air in the room, place the product about 30 cm or more from the left and right sides of the wall, furniture, curtains, etc.
  3. Do not place objects on the unit.
  4. Do not block the air inlet and outlet, for example, do not place objects on the air outlet or in front of the air inlet. G
  5. Do not pull on the power cord as it may cause a short circuit or damage to the inside of the power cord, resulting in fire or electric shock.
  6. Do not damage the power cord or plug, and do not cut, excessively twist, pull, or twist the power cord. If the power cord is damaged, it must be replaced by the manufacturer, service department or a professional to avoid danger. Non-professionals are prohibited from disassembling the machine to avoid the risk of electric shock.
  7. Do not use power supplies, universal sockets or connected devices that exceed the rated value. Using a universal outlet that exceeds the rated value or connecting the power supply may cause the power cord to overheat and cause a fire.
  8. Do not touch the power plug with wet hands, which may result in electric shock.
  9. Do not put your fingers or metal objects into the gap of the air outlet, otherwise it may cause electric shock or injury. Do not allow water, flammable detergents or other liquids to enter the product to avoid electric shock or fire.
  10. Do not use this product in a wet or hot environment such as a bathroom, toilet or kitchen
  11. Do not use air purifiers in indoors with incense-based insecticides. Chemical residues may accumulate in the machine and then be released from the air outlet to endanger your health.

SUPPORT
For more information, spare parts, technical questions and return requests concerning this product, you should contact support@mrsafe.eu.

GUARANTEE
Copyright © Mr Safe. Mr Safe® is a registered trademark of TE-Group NV. The Mr Safe® brand stands for superior product quality and outstanding customer service. That is why Mr Safe® warrants this product against all defects in material and workmanship for a period of two (2) years from the date of original purchase of the product. The conditions of this guarantee and the extent of responsibility of Mr Safe® under this guarantee can be downloaded from our website: www.mrsafe.eu.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals