hama 176564 WiFi Wall Light Instruction Manual
- June 6, 2024
- Hama
Table of Contents
**hama 176564 WiFi Wall Light Instruction Manual
**
Assembly Instruction
Operating Instructions
Explanation of product marking symbols
The product must be used only with alternating current
Please note the following: Risk of electric shock on contact
Safety Notes
- Do not drop the product and do not expose it to any major shocks.
- Do not operate the product outside the power limits given in the specifications.
- Do not modify the product in any way. Doing so voids the warranty.
- Keep this product, as all electrical products, out of the reach of children!
- The product may only be operated with the type of power supply network described on the name plate.
- Before mounting, check that the wall you have chosen is suitable for the weight to be mounted. Also make sure that there are no electric, water, gas or other lines running through the wall at the mounting site.
- Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
- Do not continue to operate the device if it becomes visibly damaged.
- No bare spots should be visible after connecting the cable.
Warning
- The device may only be operated on a 230 V 50 Hz AC voltage supply. Work with the 230 V mains supply may only be carried out by electricians certified in your country. The applicable accident prevention regulations are to be observed.
- To avoid an electric shock from the device, please disconnect the mains voltage (switch off circuit breaker). Failure to observe the installation instructions can cause fire or other hazards.
Risk of electric shock
- Do not open the product. Do not continue to operate the product if it is damaged, which may be indicated by smoke, odour or loud noises. Immediately contact your dealer or our service department (see item “Service and Support”).
- The light source of this light is not replaceable; when the light source has reached the end of its life, you need to replace the ntire light.
Mounting
- Switch off the fuse (fuse box) for the room in which you wish to install the light.
- Verify that the wires are dead using a suitable measuring device (for example, a multimeter).
- Remove the housing by pulling it upwards.
- Loosen the grub screws at the sides using the Allen key supplied.
- Pull the wires through the hole (with the rubber insulation) in the mounting plate and attach the insulating hoses. The hoses must cover the connection cable inside the lamp up to the terminals. Shorten any connection lines that are too long.
- Strip the lines as indicated on the terminals (10 mm)
- An earthing conductor cannot and must not be connected to the lamp.
- Fit the mounting plate using the screws and dowels supplied.
- Connect the wires to the light terminals. Make sure that the gasket is inserted correctly.
- Position the wall light on the mounting plate and tighten the grub screws at the sides.
- Slide the housing back onto the wall light.
It’s so simple:
- Just download the app Hama Smart Solution from the Apple app store or the Google Play store
- Start the Hama Smart Solution app
- If you’re using it for the first time, you’ll have to register and create a new account. If you already have an account, log in using your login details
- The LED should start flashing quickly (if it does not, then switch it off and back on three times quickly).
- Now click + in the upper-right corner and select Lighting.
Devices.
- Confirm that the lamp flashes quickly.
- Now enter the name of your WiFi network and the password, and confirm with Confirm.
- The lamp will now be connected. Once the connection has been established, the lamp stops flashing
- Now you can set up, control and configure your WiFi Smart LED lamp using the app
Warranty Disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/ mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.
Declaration of Conformity
****Hereby, Hama GmbH & Co KG declares that the radio equipment type [00176564] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.hama.com->00176564->Downloads.
Technical data
Input and output voltage: 220 V–240 V, 50 Hz
Frequency band: 2,4 GHz
Maximum radio-frequency power transmitted: 20 dBm
Note
Detailed operating instructions are available at
www.hama.com
Note on environmental protection:
After the implementation of the European Directive 2012/19/EU and 2006/66/EU
in the national legal system, the following applies:
Electric and electronic devices as well as batteries must not be disposed of
with household waste. Consumers are obliged by law to return electrical and
electronic devices as well as batteries at the end of their service lives to
the public collecting points set up for this purpose or point of sale. Details
to this are defined by the national law of the respective country.
This symbol on the product, the instruction manual or the package indicates
that a product is subject to these regulations.
By recycling, reusing the materials or other forms of utilising old
devices/Batteries, you are making an important contribution to protecting our
environment.
Hama GmbH & Co KG
86652 Monheim/ Germany
Service & Support
Web: www.hama.com
Call: +49 9091 502-0
“Google and Google Play are trademarks of Google LLC.”
All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.