BEC MX-210NP Mini 4G/LTE X-Range Wi-Fi Router User Guide

June 6, 2024
BEC

BEC MX-210NP Mini 4G/LTE X-Range Wi-Fi Router

BEC MX-210NP Mini 4G LTE X-Range Wi-Fi Router

PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU INSTALL THE DEVICE PROPE R LY AND AVOID IMPROPER USAGE. IF YOU NEED M ORE INFORMATION ON THIS SOFTWARE CONFIGURATION, PLEASE REFER TO THE ONLINE USER MANUAL.

Package Contents

  • BEC MX 210NP 4G/LTE Router * 1
  • This Quick Start Guide 1
  • RJ 4 5 Ethernet C able * 1
  • 4G/LTE A ntenna 2
  • DC Power A dapter * 1package content

NOTE : ALL IMAGES SHOWN ARE FOR ILLUSTRATION PURPOSES ONLY. PACKAGE CONTENTS MAY DIFFER FROM ACTUAL PRODUCTS.

Warning:

  • Do not use the router in high humidity or a  high temperature.
  • Do not use the same power source for the router as other equipment.
  • Do not open or repair the case yourself. If the router is too hot, turn off the power immediately and have it repaired at a qualified service center.
  • Avoid using this product and all accessories outdoors.

Attention:

  • Place the router on a stable surface.
  • Only use the power adapter that comes with the package. Using a different voltage rating power adapter may damage the router.

Front Panel LEDs

front panel

LED STATUS DESCRIPTION


Power

| Green| System is up and ready
Red| Boot failure



Ethernet Port LAN 1 – 2

| ****

Green

| ****

Transmission speed is at Gigabit speed (1000Mbps)

Orange| Transmission speed is at 10/100Mbps
Blinking| Data being transmitted/received




Wireless

| Green| Wireless connection established
Green blinking| ****

Data being transmitted / received

Orange| WPS configuration is in progress







LTE

(Received Signal

Strength Indicator)

| Green| RSSI greater than -69 dBm.   Excellent signal condition
Green

Flashing quickly

| ****

RSSI from -81 to -69 dBm. Good signal condition

Orange

Flashing quickly

| ****

RSSI from -99 to -81 dBm.   Fair signal condition.

Orange

Flashing slowly

| ****

RSSI less than -99 dBm. Poor signal condition.

Orange| No signal and the cellular module is in service
Off| No LTE module or LTE module fails
Green & Orange| ****

MX-210NP is either in debug mode or in upgrading firmware process

Internet| Green| IP address has received; traffic is passing thru the device.
Red| IP address request has failed.
Off| MX-210NP is either in bridged mode or WAN connection not ready.

**Rear Panel Connectors

rear panel**

INTERFACE MEANING


1

| ****

4G/LTE Antenna Connectors (Main/Aux)

| SMA female connectors.

Manually screw the cellular antennas tight to the female connectors. Connect to Main if decide to use single antenna instead of two.



2

| ****


Power Source

| Power ON/OFF switch

(1) with Power Switch ON: power up by the supplied DC power adapter

(2) with Power Switch OFF: power up by the PoE battery unit


3

| Power Jack (DC IN)| ****

Connect the supplied Power Adapter to this jack.


4

| ****

Reset

| After the device is powered on, press it 6 seconds or above : to restore to factory default settings (this is used when you cannot login to the router, e.g. forgot your password)



5

| ****

Gigabit Ethernet (LAN 1 / PoE)

| Ethernet LAN : Connected to a 10/100/1000Mbps Ethernet device

Ethernet PoE :   Connect to an 802.3at Gb PoE injector to provide power to the MX-210NP


6

| ****

Gigabit Ethernet (LAN 2 / EWAN)

| Ethernet LAN : Connected to a 10/100/1000Mbps Ethernet device

Ethernet WAN : Software configurable in the GUI.    Connect to a broadband device such as a cable modem, ADSL/VDSL modem or fiber modem.


7

| GPS Antenna Connectors| SMA female connectors.

Manually screw the GPS antenna tight to the female connector.



8

| ****


SIM Card Slot

| Insert the mini SIM card (2FF) with the gold contact facing down. Push the mini SIM card (2FF) inwards to eject it

  • Power off the MX-210NP before inserting or removing the SIM card(s)

Hardware Connection

  1. WAN : 4G/ LTE
    Power Source: DC Power ( ON)
    LAN : Ethernet Deviceshardware connection 1

  2. WAN : 4G/LTE Power
    Source : PoE Injector (O FF ).
    LAN1 : Connect to the PoE injector
    LAN2 : Ethernet Device (notebook, switch, etc.)hardware connection
2

  3. WAN : Ethernet WAN (LAN2)
    Power Source: DC Power Adapter (O N ).
    LAN1 : Ethernet Device (notebook, switch, etc.)
    LAN2 : Wireline Modemhardware connection 3

Hardware Installation

  1. Power Connection
    Select power source from using a (1) DC power adapter or (2) PoE Injector
    Using the Supplied DC Power Adapter
    Plug in the supplied power adapter to the wall jack, the other side to the MX- 210NP then power it ON the by pressing the Power On/Off button.hardware
connection 4
    Using a PoE Injector
    Power OFF the power source button then plug an Ethernet cable (RJ-45) to the LAN 1/PoE IN port and the other end of the cable directly to the Data+Power of the PoE injector.hardware connection 5

  2. LAN Connection
    Plug the RJ-45 Ethernet cable to one of the Ethernet ports, and the other side to the PC’s Ethernet interface.hardware connection 6

  3. WAN Link Interface and Connection
    BEC MX-210NP supports failover and failback on dual WAN interfaces, 4G/LTE and ETH WAN.
    Mobile 4G/LTE Connection
    Slide the SIM card into the card slot of the device with the gold contact facing down. Make sure that the SIM card has been slid into the bottom of the slot with a click. When removing the SIM card, press the SIM card again it will be ejected from the card slot.hardware connection
7
    WARNING: Please power off the device before inserting or removing the SIM.
    Ethernet WAN Connection
    Connect RJ-45 Ethernet cable to the EWAN port, and connect the other side to another alternative broadband device, such as Cable Modem, VDSL, Fiber Modem or PON optic lines.hardware connection 8

Connecting to the Router

The default IP of modem is 192.168.1.254 with subnet 255.255.255.0. Make sure the attached PC to thi s router is in the same subnet and has an I P ad dress i n the range between 192.168.1.1 ~ 192.168.1.253. Open a web browser and type http://192.168.1.254 in the URL address bar.hardware connection
9

The login prompt will appear. Input the default username and password. This username/password may vary by differe nt I nternet Service Providers.

Quick Setup Your Router

Step 1: Change administration password
Setup a new password for “admin” account for device management. The default password is “admin”. Click Continue to go on to the next step. The password may vary by different Internet Service Providers.hardware connection
10

Step 2: Time Zone configuration
Enable and select your Time Zone then click Continue to go on to the next step.hardware connection 11

Step 3: Setup Wireless Connectionhardware connection
12

Step 4: WAN / Internet Connection Setup
Select the appropriate WAN protocol then fill out the information provided by your ISP in all relevant parameters.
Example : WAN Interface in EWAN mode.hardware connection
13

Step 5: Save Confirmation Settings
Click “Next” to save and complete the Quick Setup. You should now be able to access to the Internet.
Please see the relevant sections of User Manual for detailed information.

Troubleshooting

  1. None o f the LEDs are on when you turn on the rout er.
    Check the connection between the adapter and the router. If the error persists, you may have a hardware problem. In this case you should contact technical support.

  2. You have forgotten your router login and/or password.
    Try the default login and password, please refer to User Manual . If this fails, you can restore your router to its factory settings by holding the Reset button on the back of your router for 6 seconds or more.

  3. Can’t ping any PCs on the LAN.
    Check the Ethernet LEDs on the front panel. Th e LE D shoul d be on for a port that has a PC connected. If it is off, check the cables between your router and the PC. Make sure you have uninstalled any software firewall for troubleshooting. Verify that the IP ad d ress and the subnet mask are consistent between the router and the workstations.

Product Support and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the User Manual If you have other inquiries or need fur t her technical support, please contact with you r Inter net Service Provider or visit us at www.bectechnologies.net

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference
  2. This device must accept any interference received, including interference that may cause undesired operation.
    Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals