BRESSER BR-PH30 Photobox + Light 30x22x23cm Instruction Manual

BRESSER BR-PH30 Photobox + Light 30x22x23cm Instruction Manual

About this Instruction Manual

These operating instructions are to be considered a component of the device.
Please read the safety instructions and the operating instructions carefully before use.
Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the instruction manual must be provided to the new owner/user of the product.

Intended Use
This product is intended only for private use. The device is intended only for indoor use.

General Warning

RISK OF CHOKING!
Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.

RISK of ELECTRIC SHOCK!
This device contains electronic components that operate via a power source (power supply). Only use the device as described in the manual; otherwise, you run the risk of an electric shock.

Position your device so that it can be disconnected from the power supply at any time. The wall socket you use should be located near the device and easily
accessible, since the plug on the power cable serves as a disconnecting device for the power supply.
Always pull on the plug to separate the device from the power supply. Never pull on the cable.
Never bend, pinch or pull the power and connecting cables, extensions and adapters. Protect the cables from sharp edges and heat.
Before operating, check the device, cables and connections for damage. Never use a damaged unit or a unit with damaged power cables. Damaged parts must be exchanged immediately by an authorised service centre.

RISK of FIRE/EXPLOSION!
Do not expose the device to high temperatures.
Use only the supplied power adapter. Do not shortcircuit the device or throw them into a fire. Excessive heat or improper handling could trigger a shortcircuit, a fire or an explosion.

NOTE!
The manufacturer is not liable for voltage damage due to the use of an improper power adapter.

What to do in case of a lamp break?

The quantity of mercury used for the light tubes and energy-saving lamps is very low. The consumer will get in contact with the mercury in case of a lamp break (broken flash tube). The quotation of mercury that may the customer get in contact with is very low and in most cases the concentration is below German limiting values.

When a lamp is broken, disconnect the light from the main power supply to avoid any electrical shock. As mercury is spreading at ground level, children and animals must leave the room immediatlely. Open the windows for ventilation and leave the room for approx. 15 minutes. It is also recommended to turn off heating, air conditioning, ventilators or wind machines.

After ventilation you will have plenty of time to take care of a thorough cleaning. The remaining mercury will vaporize slowly under normal room temeprture.
In case of a broken lamp the mercury can cling to fragments and vaporize in the room during the time.

To prevent this take the following measures:

Put on disposable or household gloves.
Avoid violations due to glass fragments.
Sweep up all fragments with a cardboard, collect them in a container or bag (e.g. preserving jar, plastic bag) and close it.
Use a moistened disposable household wipe or an adhesive tape to put up smaller parts.
If you have used other utensils (e.g. a hand brush), wipe them with a moistened cleaning cloth after use. Put the utensils out to air.
Dispose cleaning cloth and cardboard in a dustbin.
Please bring the container/bag with the glass fragments to your local collecting point for used lamps. In the meantime, store it outdoors if possible.

Use a vacuum cleaner if neccessary (e.g. on areas with carpets).

Air the room during the use of the vacuum cleaner and 15 minutes additionally after you have finished cleaning.

Dispose the bags or the dirt of the vacuum cleaner in a dustbin.

Clean the container of your vacuum cleaner thoroughly. Wipe the floor nozzle with a moistened cleaning cloth. To clean the vacuum cleaner, run it outdoors for approx. 15 minutes.

After all cleaning procedures have been finished, air the room again for a some time.
Wash your hands thoroughly.

When carefully collecting the glass fragments in a closed container or bag and storing it outdoors until its disposal, the mercury will not spread in the room.
There will be no risk to your health.

Scope of delivery / Parts overview

1. Plastic plate (6 pcs.)
   • for the right and left side (2 pcs.) (Side plate)
   • for the frontside (1 pc.)
   • for the top side (1 pc.)
   • for the backside (1 pc.)
   • for the bottom side (1 pc.) (Base plate)
2. Small cover plate (1 pc.)
3. Aluminium tube (5 pcs. or 4 pcs.)
4. Aluminium rail (1 pc.) (eventually pre-assembled to 1b)
5. Screw (10 pcs. or 8 pcs.)
6.  Vinyl background (1 pc.)
7. Background paper (2 pcs.)
8. Fixing clips (4 pcs. or 2 pcs.)
9. Lamp socket (2 pcs. or 1 pc.)
10. Light tube (2 pcs. or 1 pc. – 5600K Daylight DL)
11. Holder for lamp socket (4 pcs. or 2 pcs.)
12. Connecting cable (1 pc., included only with two lamp sockets)
13. Power cable (1 pc.) with
    • Power plug
    • Plug for lamp socket
    • On/Off switch

Assembling the photo box

• Fig. 2: Attach the aluminium tubes (3) and the aluminium rail (4) to the plastic plate for the right and left side (1a) and fix them with the screws (5). Tighten the screws only by hand.
  
  NOTE!
  The aluminium rail (4) can be delivered as a preassembled part of the plate for the front side. In this case, please assemble the rail together with plate (Fig. 6 can be ignored then).

• Fig. 3: Insert the the plastic plate for the bottom side (1e). Make sure that the profile sections of the base plate (1e) match with the cut-outs of the side plates. Tighten the screws (5) by hand.
  

• Fig. 4: Move the plastic plate for the backside (1d) from the top to the bottom through the notches of the side plates (1a).
  

• Fig. 5: Insert the plastic plate for the top side (1c).
  

• Fig. 6: Attach the plastic plate for the frontside (1b) to the aluminium rail (4).

Inserting the background

• Fig. 7: Carefully move the vinyl background (6) from the front between aluminium rail (4) and base plate (1e) to the rear. The background will slide along the backside (1d) to the top side (1c) by itself. It will form a slightly curved background.
  

• Fig. 8: Depending on the desired background and the object, you can add one of the background papers (7) by pushing it over the vinyl background (6) in the same way.
  

• Fig. 9: Use the fixing clips (8) to fix the vinyl background (6) and the paper background (7) on the backside (1d).

Installing the lighting

• Fig. 10 (Assembling step depending on model; only neccessary/possible with two lamp sockets):
  Connect both lamp sockets (9) with each other by using the connection cable (12).
  

• Fig. 11: Attach the holders (11) to the lamp sockets (9). Insert the light tube (10) into the socket, if it was not assembled in the factory.
  

• Fig. 12: Open the top side plate and fix the lamp sockets (9) with the holder clips (11) on the upper aluminium tubes (3).
  

• Fig. 13: Put the power plug of the power cable (13b) through the oval hole of the right or left side plate (1a).
  

• Fig. 14: The lamps should be placed in the middle of the photo box. Put the power plug of the power cord (13a) into a wall socket after the lamps have been attached, Use the On/Off switch (13c) to turn on the light and start your photo shooting.
  

Exchanging the light tube

ATTENTION!
Disconnect the light source from the power supply (remove plug) before every cleaning and maintenance!

• Fig. 15: Carefully turn the light tube (10) through approx. 90 degrees and pull it out of the socket (9) upwards. Work in the reverse way when inserting a new light tube.
  

Cleaning

Only use a slightly moistened cloth to clean the exterior of the device. use a little eyeglass-cleaning solution to remove more stubborn dirt.

Only clean the lamp sockets and the light tubes with a dry cleaning cloth or dust cleaning brush.

Disposal

Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal.

Do not dispose of electronic devices in the household garbage!
As per Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.

EC Declaration of Conformity

Bresser GmbH has issued a “Declaration of Conformity” in accordance with applicable guidelines and corresponding standards. This can be viewed any time upon request.

Technical Data

http://www.bresser.de/download/photoboxes

WARRANTY & SERVICE

The regular guarantee period is 5 years and begins on the day of purchase. You can consult the full guarantee terms as well as information on extending the guarantee period and details of our services at www.bresser.de/warranty_terms. Would you like detailed instructions for this product in a particular language? Then visit our website via the link below (QR code) for available versions. Alternatively you can also send an email to manuals@bresser.de or leave a message on +49 (0) 28 72 –80 74-220 *. Please always state your name, precise
address, a valid phone number and email address, as well as the article number and name.
Number charged at local rates in Germany (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs

Find us on Facebook:

http://www.bresser.de/start/bresser

Contact

Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>