Rowenta IR 3020 1800 Watt Bathroom Heater Instruction Manual

: June 5, 2024
: Rowenta

Table of Contents

IMPORTANT INFORMATION
VOLTAGE
INSTALLATION
OPERATION
CLEANING
IN THE EVENT OF PROBLEMS
ENVIRONMENT PROTECTION FIRST!
Read User Manual Online (PDF format)
Download This Manual (PDF format)

IR 3020 1800 Watt Bathroom Heater
Instruction Manual

It is essential to read these instructions carefully and to observe the following recommendations :
A – Radiant part
B – Attachment box
C – Wall bracket
D – Unit mounting screw
E – Orientation adjustment screws (1 screw on each side)
F – Selection pull-cord
G – Rear part

IMPORTANT INFORMATION

For your safety, this appliance complies with the applicable standards and regulations (Low Voltage Directive, Electromagnetic Compatibility, Environmental…).
This appliance is intended only for domestic use. It may not be used for industrial purposes.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Do not fit your appliance just above a wall-mounted electricity socket.
Do not operate your appliance in a dusty atmosphere or where there is a fire risk.
Before each use, check that the appliance is in good general condition.
Do not place towels or clothing on the appliance.
Never insert objects into the appliance (e.g. needles).
The guarantee is void in the event of damage resulting from improper use.
Disposal at the end of the product life: take your appliance to an appropriate waste collection point.

VERY IMPORTANT

Do not use your appliance near inflammable objects and materials (curtains, aerosols, solvents, etc.).
Never cover the appliance, even temporarily – it may overheat and be damaged beyond repair.
Do not touch the appliance with wet hands.
Never allow water to get into the appliance.
DO NOT ATTEMPT TO TOUCH THE RADIANT PART DURING OPERATION (this part reaches a high temperature and can cause severe burns). It is recommended to wait 15 minutes after switching off the appliance before touching it.
This appliance is only intended for use when fixed to the wall in a horizontal position and correctly oriented (see chapter “INSTALLATION”).

VOLTAGE

Before using it for the first time, check that the supply voltage matches that indicated on the appliance.
This is a class II appliance (double electrical insulation ). It should not be earthed.

INSTALLATION

Take the advice of a specialist on the appropriate means of installation.
Your appliance must be oriented as shown in Figure 2 (Selection indicator on the right) and must be positioned so as to allow the minimum clearances shown in the same diagram, as well as in accordance with the “Bathroom Installation” safety rules defined in the paragraph “Bathroom Installation” (Fig. 1).
The radiation intensity is relatively high in the vicinity of the appliance, which can raise objects in this area to a high temperature.
You should, therefore, install your radiator with a clearance of 80 cm from any object.
It is strictly FORBIDDEN to fix the appliance to the ceiling or to the wall in a vertical position.
The switches or other control equipment must be beyond the reach of any person using the bath or shower.
BATHROOM INSTALLATION (FIG. 2)
The IP24 construction of this appliance enables it to be used in any room in the house, including those where there is a risk of water splashing (kitchen, bathroom, etc.).
The electrical installations in the room, the installation of the appliance, and its use must, however, be compliant with the regulations in force in your country.

PROCEDURE FOR MOUNTING AND CONNECTING THE DEVICE TO THE MAINS :
Before any assembly or dismantling operation, ensure that the circuit providing power to the radiator has been cut off.
Fixing the appliance in place :

Take the wall bracket C and attach it horizontally to the wall, in accordance with marks indicating the position of the appliance (see Fig. 1 and 2).
To ensure your radiator is firmly attached, you must use plugs and screws that are compatible with the material of your wall.
Take the appliance and attach it to wall bracket C (see Fig 3) and then lock it onto bracket C with screw D.

Setting the pitch :
The radiating part of your radiator can be tilted (Fig.4) from 0° to 30° to the wall.
The tilt must not be adjusted while the appliance is operating.
To change the angle, it is recommended that you wait 15 minutes after the appliance has stopped and that you follow the following procedure :
– untighten the 2 screws on the pivot in order to enable the radiating part to rotate.
– hold the radiating part in the position you want and tighten the 2 screws on the pivot.
Connecting the device to the mains :
Your appliance comes with a cord for connecting to a junction box.
According to electrical installation regulations, there must be a multiple pole isolator on the power supply.
This isolator must have a contact push-off of at least 3 mm on every pole.
The power cord should be cut in order to only keep the length necessary for the connection.
After installation, the power cord will be fixed in the wall or on the wall to make sure that the power cord will not touch the high-temperature metallic parts (A and G).

OPERATION

The appliance is turned on by means of the pull cord (Fig. 3). When turned on there may be a slight vibration, which should stop after a few seconds.
Mod. IR3020

Position 0: Off
Position 1: 600 W
Position 2: 1200 W
Position 3: 1800 W

CLEANING

It is imperative that you turn off your appliance (selection indicator at 0) and leave it to cool down properly before cleaning.
It can be cleaned with a damp cloth.
Important: Never use abrasive cleaners, these will damage the surfaces.

IN THE EVENT OF PROBLEMS

Never dismantle your appliance. An incorrectly repaired appliance can be a danger to the user.
Before doing anything to the appliance, ensure that:
– your appliance is turned off (selection indicator at 0),
– your appliance has cooled down,
– the supply circuit to your radiator is off.