SilverStone M.2 SSD Cooling Kit with ARGB Lighting TP03-ARGB Instruction Manual

SilverStone M.2 SSD Cooling Kit with ARGB Lighting TP03-ARGB

Installation guide

• TP03-ARGB heatsink x 1
• Blue high conductivity thermal pad (1.5mm) x 2
• Blue high conductivity thermal pad (1.0mm) x 2

1. Use a flat screwdriver to slightly open the stainless steel bottom cover to separate it from the aluminum heatsink

2. Stick the blue thermal pad on the back of heatsink and also on the inner side of the stainless steel bottom cover

3. Install the M.2 SSD into the stainless steel bottom cover. Be careful not to put it directly in from above, as it must be inserted from the front or back ends and below the buckle point

4. Place the aluminum heatsink on to the stainless steel bottom cover, then click in the buckle points on both sides

5. Install on to the motherboard and connect the ARGB cable to the motherboard ARGB header

Attention

• Includes two blue colored thermal pads with different thickness. For single sided M.2 SSD (flat back without component), please use 1.5mm thick pad; for double sided M.2 SSD (both sides with components), please use 1mm thick pad.
  ** Due to the thermal pads being sticky, if it needs to be removed, please do so carefully to avoid damage to the M.2 SSD.

Warranty terms & conditions

Warranty terms & conditions 

1. Product component defects or damages resulted from defective production is covered under warranty. Defects or damages with the following conditions will be fixed or replaced under SilverStone Technology’s jurisdiction.
   a. Usage in accordance with instructions provided in the manual, with no misuse, overuse, or other inappropriate actions*.
   b. Damage not caused by natural disaster (thunder, fire, earthquake, flood, salt, wind, insect, animals, etc…)
   c. Product is not modified or components replaced resulting in out of spec. operation.
   d. Loss or damages resulted from conditions other than ones listed above are not covered under warranty.

2. Under warranty, SilverStone Technology’s maximum liability is limited to the current market value for the product (depreciated value, excluding shipping, handling, and other fees). SilverStone Technology is not responsible for other damages or loss associated with the use of product.

3. Under warranty, SilverStone Technology is obligated to repair or replace its defective products. Under no circumstances will SilverStone Technology be liable for damages in connection with the sale, purchase, or use including but not limited to loss of data, loss of business, loss of profits, loss of use of the product or incidental or consequential damage whether or not foreseeable and whether or not based on breach of warranty, contract or negligence, even if SilverStone Technology has been advised of the possibility of such damages.

4. Warranty covers only the original purchaser through authorized SilverStone distributors and resellers and is not transferable to a second hand purchaser

5. You must provide sales receipt or invoice with clear indication of purchase date to determine warranty eligibility.

6. If a problem develops during the warranty period, please contact your retailer/reseller/SilverStone authorized distributors or SilverStone http://www.silverstonetek.com.

Please note that: (i) You must provide proof of original purchase of the product by a dated itemized receipt; (ii) You shall bear the cost of shipping (or otherwise transporting) the product to SilverStone authorized distributors. SilverStone authorized distributors will bear the cost of shipping (or otherwise transporting) the product back to you after completing the warranty service; (iii) Before you send the product, you must be issued a Return Merchandise Authorization (“RMA”) number from SilverStone. Updated warranty information will be posted on SilverStone’s official website. Please visit http://www.silverstonetek.com. for the latest updates.

Additional info & contacts
For North America usasupport(at)silverstonetek.com
SilverStone Technology in North America may repair or replace defective product with refurbished product that is not new but has been functionally tested. Replacement product will be warranted for remainder of the warranty period or thirty days, whichever is longer. All power supplies should be sent back to the place of purchase if it is within 30 days of purchase, after 30 days, customers need to initiate RMA procedure with SilverStone Technology in USA by first downloading the “USA RMA form for end-users” form from the below link and follow its instructions. http://silverstonetek.com/contactus.php

For Australia only support(at)silverstonetek.com
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Please refer to above “Warranty terms & conditions” for further warranty details. SilverStone Technology Co., Ltd. 12F No. 168 Jiankang Rd., Zhonghe Dist., New Taipei City 235 Taiwan R.O.C. +886-2-8228-1238 (standard international call charges apply)

For Europesupport.eu(at)silverstonetek.de
For Chinasupport(at)silverstonetek.com.cn
For Japansupport_jp(at)silverstonetek.co.jp
For all other regionssupport(at)silverstonetek.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>