TVCMALL VM17 Car Head UP Display User Manual

Car Head-Up Display
(Model: M17)

This product Design Patent and Display Images Copyright had been registered with customs record

Special Reminder:

The working voltage of this product: 11r18Vdc (12Vdc/200mA). Please use the USB cable If the car voltage is> 24V. This product is a dual system: Users can freely choose the mode(press the ‘ + ‘ key to select OBD or GPS system) before the 08D icon on-screen stops to flash, it will automatically save and enter your last selected option.

Product Introduction:

HUD short for Head-Up Display, the main function is to reflect the car dashboard information (e.g. speed, RPM, water temperature,yoltageolp distance, etc), and keep the driver eyes always on road to avoid the danger of lowering down head to read the instrument.

Product function:

1. Light sensor: HUD can automatically adjust the brightness according to the environment
2. Speed icon: OBD mode: speed Car ECU data, GPS mode: satellite data like a compass
3. System icon: short press the ` + ‘ key within 5 seconds to choose OBD or GPS system
4. Multi-function area: Speed,water temperature,voltage,mileage,driving time,fuel consumption, altitude,clock,100 kilometers acceleration
5. a + =100km acceleration, ASL=altitude, LHK=fuel consumption, MIN=travel time, TRIP=travel mileage
6. Water temperature icon, Voltage icon
7. Over-speed alarm icon
8. Driving direction: Driving direction indication: W=West, N=North, S=South, E=East when the vehicle speed >5KM / H
9. Speed display area
10. Speed unit: KM/H=kilometer/hour, MPH=Mile/hour
11. Satellite icon: flashing will stop until satellite numbers have been got, please move the car to the open road, the GPS light will stay on if a satellite signal has been found.

Button functions:

short press(1 second press)
long press(3-second press)

1. Button**M**
   A.Short PressM
   (1) OBD system: to switch functions between speed,voltage,water temperature,altitude,fuel consumption,driving time,mileage,clock,100 kilometers acceleration.
   (2) GPS system:to switch functions between voltage,altitude,travel time,travel mileage,clock,100km accelerationenumber of satellites.
   B.Long PressM
   (1) To enter into menu settings (Menu 1-14) (2) To save your settings and exit

2. Button
   A.Short Press –
   (1) Switch the mode OBD or GPS within S seconds when the power-on screen flashes
   (2) To switch the RPM icon
   (3) Menu or parameter value – after entering the setting
   B.Long Press-
   (1) Turn off the buzzer, again to turn on the buzzer

3. Button+
   A.Short press +
   (1) Switch the mode OBD or GPS within S seconds when the power-on screen flashes
   (2) Menu or parameters value +
   B.Long press+
   (1) Long Press: To clear engine fault codes(till all of the LED lights is lighting), again to return to your main page

4. Power switch:
   Long press to turn off again to turn on

5. Connection 1 and 2:
   You can freely choose one of them
   System selection
   Please press’ +’ or ‘-‘ button to switch the mode OBD or GPS within 5 seconds when the OBD icon flashes
   OBD System (For OBD2 car)
   Functions:Vehicle speed,engine RPM,water temperature,voltage,fuel consumption,altitude,clock, travel time,travel distance,number of compass satellites.
   GPS System (For all cars)
   Functions: Speed, Voltage, Compass, Number of Satellites, Speed Icon, Decorative bar
   When the OBD system is not compatible, please switch to the GPS system and plug with the USB cable
   GPS system use
   GPS flashing is in the state of searching for stars. Please move the car to an open road. After the satellite is found, the GPS light stops flashing and stays on for normal use.
   Restore setting
   Unplug the power,long-press the ‘ M ‘ key and don’t release it, plug in the power and release the ‘ M ‘ key after the screen is fully lit.

DTC Trouble Code Search

Search

OBD-II search powered by dot.report

Clear the fault codes

1. Powering on the connection agreement,
2. Long press the ‘ +’ key and the HUD screen will light up and clear the fault code,
3. Long press the ‘ + ‘ key again to exit.

Turn off/on the buzzer
long press and hold the button to turn off the buzzer, again to turn on.
Display mode switch
After HUD is turned on, short press the 41 key to switch the modes.(concise/racing/standard mode)

Menu setting

Please refer to the reflective image on the windshield for operation when setting. Long press and hold the ‘ M ‘ button to enter into setting menus(1-14). The menu is displayed 1, short press the ‘+’ button to increase the menu options, short press ‘V or button to adjust the parameter value, short press ‘ M ‘ button to return to the menu, long press ‘ M ‘ button to save and exit.

Menu| Functions| Adjust Range| Explanation| Default
value| Setting screen
---|---|---|---|---|---
1| Speed| 50-150| Adjust when speed is not correct. For example, the instrument displays 100 KM / H, the device displays 105KM / H, and the parameter value is adjusted to 102| 107|
2| Fuel Consumption| 50-150| Adjust parameter value when there is an error in fuel consumption| 100|
3| RPM Alarm| 10-75| Alarm after the speed reaches the set default value of 7500 rpm| 75|
4| Over-speed Alarm| 30-250| Over-speed alarm is 150KM/H, users can freely set this value| 150|
5| Water Temperature
Alarm| 50-150| Water temperature alarm is

120t, users can freely set this value

| 120|
6| Voltage alarm| 0-15.0| Voltage alarm is 1W, users can freely set this value| 10.0|
7| Fatigue
Driving
Reminder| 1.0-8.0| Remind after continuous driving exceeds the default value of 4.0 hours| 4.0|
8| Brightness
Level| 0-11| 0-automatic photosensitive mode, 1-11 Is the manual adjustment| 0|
9| Speed Unit| 0-1| 0=KM/H 1=MPH| CD|
10| Temperature
Unit| 0-1| 0= Celsius

1= Fahrenheit

| 0|

11| Shutdown
Voltage| 0-15.0| Adjust the voltage to 13.2 volts when unable to shut down| 0|
12| Shutdown
Time| 5-300| Shut down 20 seconds after the fire break, turn off the gas and electricity to 180, that is, shut down after 180 seconds.| 20|
13| Time
Calibration| as

gg gl

| Time adjustment, choose the time of your area, after searching for satellites, you can directly adjust to the local time. ( dial-up to increase time zone time, dial down to decrease time zone time)| HUD displays 8 before the star Is found, and displays

the GMT+8 (China

time)

|
14| Factory Reset| 0-1| The default value is O. When set to 1, press the key for 5 seconds to save and exit| 0|

Remind warning:
Please disconnect the HUD if you don’t drive for more than a week. Generally speaking, the car battery’s standby time is 1 month, we kindly suggest you unplug the
OBD device when the car is not used for a long time due to different vehicle conditions.
OBD FAQ:

1. No function is displayed, no power
   Check whether the 080 cable is a tight connection, pull down repeatedly to confirm, please try it on another car If still not workable, analysis If It Is a cause from 0130 diagnostic Interface” yes, please repair it and connect the device again.

2. Only the car voltage displays and is automatic powered off after 30 seconds
   (1) This product is only available for OBDII and EOBD cars when it is in 0802 modes
   (2) 0802 Is a car protocol (U.S.A Cars:2003 Other regions:2007)
   (3) This product OBD2 mode does not support 01301 and 1080
   (4) Switch to the GPS system using the Use cable to display, within S seconds of power short press the ‘ +’ key to select the GPS system.

3. the Wrong operation leads to crashes
   (1) Are there other OBD devices on your car(parking sensor, TPMS, lock lift window, ELM27)
   (2) Had your car been modified and brushed(central navigation, electronic throttle controller, fixed speed cruise, reset the computer system)
   (3) No matter engine start-stop, keyless entry, or remote start will cause a crash, unplug other 080 devices, and do a factory reset (see the menu settings) Please switch to a GPS system (short press ‘+’ within Ss) which should be connected with a USI3 cable.

4. Inaccurate speed
   (1) Please check that the unit is correct KM/mile MPH, (speed unit switch please refer to the settings)
   (2) When the power Is turned on, long-press the ‘ M ‘ key for 5 seconds to enter the menu options, the menu displays 1, and short press the ‘+’  key to enter the parameter value 107 and flash. According to the difference between HUD and your dashboard, adjust the parameter value (Device displays 105KM/H, adjust the parameter value to 102 through the key)
   (3) After adjustment, long-press the ‘PA’ key for 5 seconds to exit

5. Automatik start-up will auto off when stepping the brake
   (1) Enter the menu and adjust the shutdown time. (See the menu settings)
   (2) Setting shutdown delay to 300 seconds, so that it can turn off after 5 minutes

6. This device cannot auto shut down
   After the car engine stops, the RPM and speed on the machine can not be turned off, please enter the setting menu and short press the ‘+’  key to item 11, set the voltage to 13.2V or 13.5V so that the car can be turned off after 3 minutes. (See the menu settings)

7. Shut down and restart Indicates that the voltage Is higher than the starting voltage 13.2V, enter the setting menu and short press the ‘+’ key to item 11, set voltage to 13.6-13.8V (the device can only be turned on after the vehicle voltage Is higher than the setting voltage)

GPS FAQ:

1. Nothing on the screen, no power
   Check if the US8 interface has power or the connection is loose, pull it out and plug it in again several times, or replace the US8 cable

2. No speed
   The GPS is flashing to search for stars. Please move the car to an open road. After the satellite is found, the GPS light will be on and off, and It can be used normally.

3. Can not automatically turn on or turn off repeatedly during driving
   Long press the ‘M’  key for 5 seconds, enter the setting menu, short press the ‘ +’ key to item 11, and adjust the parameter value voltage to 13.0V or 12.8-12.5V If not resolved, please use the US8 cable to plug into the cigarette lighter

4. Inaccurate speed
   When the power is turned on, long-press the ‘M’ key for S seconds to enter the menu options, the menu displays 1, short press the qvis key to enter the parameter value 107 and flash, fine-tune the parameter value according to how much difference between device and the dashboard. (the dashboard displays 100 KM /H, the device displays 105KM/H and adjust the parameter value to 102 through the key), after adjustment, long-press the ‘M’ key for 5 seconds to exit.

5. Inaccurate Satellite Time
   Enter the setting menu item and short press the’ +’ key to item 13, short press ‘+’ key to adjust the local time zone, if the HUD finds the satellite signal, only need to adjust to the local time, after adjustment, press the ‘M’ key for 2 seconds to save and exit.

6. Wrong driving direction
   It will be normal until >5KM/H

7. Speed Is still on after the car stops
   Underground parking lots, tunnels, and overpasses, when there are obstructions, the signal will be unstable. Satellites will drift. Please drive to an open road. If the number of satellites found is more than 5, it will be normal.
   

8. Check the number of satellites
   Short press the ‘M’ key to switch vehicle speed, voltage, number of satellites (more than 5 satellites can be displayed normally)

9. Cannot automatically turn off after the car shutdown When the OBD cable is connected, the HUD will automatically shut down after 3 minutes if the machine is not turned off after 5 minutes after stopping the flame, adjust the voltage setting parameter value of item 11 to 13.5V ( (See the menu settings) Or directly plug into the cigarette lighter with a USB cable

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>