ZACO V4 Robotic Vacuum Cleaner User Manual

June 6, 2024
ZACO

ZACO logo

ZACO V4 Robotic Vacuum Cleaner

ZACO V4 Robotic Vacuum Cleaner

Dear Customer,
Thank you for purchasing ZACO V4 robot vacuumcleaner! You have joined the millions of people who clean with robots – the smarter way to get it done.
Please take a few moments to read this manual and get acquainted with your robot, to get the best performance from your robot.
If you have any problem when you use it, please don’t worry, you are supposed to contact our customer service firstly, we will support you during this process.

ZACO Customer Service
Customer Service Number:
00800-42377961 (European Free Call)
0209-513038-383 (Direct Line DE}
Email: support@zacorobot.eu

Important Tips

Operate

Important Tips

  • Make sure the power switch is turned on before using the robot.
  • Robot will repeat cleaning the same areas a few times to ensure they are thoroughly cleaned.
  • There may be small particles such as dog food and cat litter scattering on the floor while the spinning brushes are working. The vacuuming function will clear up the debris.
  • When replacing the side brushes, make sure they are installed according to the “L” and “R” marks on both sides of the brush and the base of the robot.
  • Successful clock and schedule settings will be confirmed by a “beep” sound.
  • Empty the dustbin if the robot vacuums less or spits debris out.
    No alert will be given for a full dustbin.

For best performance

  • Empty the dustbin and clean the high-performance filter after each use.
  • Filter could not be washed with water.
  • Replace the high-performance filter when suctioning power weakens or when the robot picks up less debris.
  • Put the charging dock against a wall and remove obstacles about 1 meter on both sides and about 2 meters in front.
  • Fully charge the robot before each operation.

Extending battery life
To extend V4’s battery life and keep its cleaning performance at its best:

  • Before first use, charge the robot overnight.
  • If the robot will not be used for a long time, switch the power off.
  • Recharge the robot soon after each use. Robot in low battery status may damage the battery.
  • Use the robot regularly.

Warning: V4 contains electronic parts. Do NOT put it in water or spay it with water. Clean the robot with a dry cloth only.

Safety Instructions

Before using the robot, please read and follow the safety instructions and precautions below.

• Read through this user manual carefully before using the robot.
• Retain this user manual.
• Any operation that is not described in this user manual may injure the users and cause product damage.

WARNINGS

  1. Only certified technicians may disassemble the robot. Users must not disassemble or repair the robot.
  2. Use factory authorized adapter only. Using nonspecific adapter may cause electric shock, fire or robot damage.
  3. Do not touch the power cord, plug or adapter with wet hands.
  4. Do not allow clothes or any part of your body to be drawn into the robot’s wheels.
  5. Do not place the robot near cigarette, lighter, matches or other flammables.
  6. Clean the robot after charging finishes.
  7. Do not over-bend the power cord or pressure the power cord with heavy or sharp objects.
  8. Do not use the robot outdoor.
  9. Do not sit on the robot or attach any object on it.
  10. Do not use the robot on wet floors.
  11. Before using the robot, remove all fragile objects (textile, glass, lighting, etc) and other objects that could get caught in the brushes or suction opening (cords, clothing, papers, drapes, blinds, etc) on the floor.
  12. Do not place the robot where it could easily fall off (tables, chairs, etc).
  13. Turn off the power switch during transportation or when the robot will not be used for a long time.
  14. To avoid battery damage, check if the adapter and outlet are properly connected before using the robot.
  15. To avoid tripping, make sure everyone in the house knows the robot is working.
  16. Use the robot in environment between -10° and 40° Celsius.
  17. Do not place the robot in high-temperature environment.
  18. Before scrapping the battery, remove it from the robot.
  19. Disconnect electricity supply before removing the battery.
  20. The battery is to be disposed of safety according to local regulations.

NOTE: This robot should not be used by children, people who lack related experience and knowledge (unless they are under proper supervision).

Product Parts

Main body and accessories
NO. Description Qty
1 Main Body (battery included) 1
2 Charging Dock 1
3 Remote Control (battery not included) 1
4 Power Adapter 1
5 Cleaning Tool 1
6 User Manual 1
7 Extra Side Brushes 2
8 High Performance Filters 2
Robot anatomy

Product Parts 1

Product Parts 2

Product Parts 3

Charging dock

Charging dock

Remote control

Remote control

CLEAN button signals

Robot Status                    Light signal
Charging                            Middle light in orange flash steadily
Charging finished              All lights off
In selected mode               Three lights flash in green
Malfunctioning                  Middle light flash slowly in red
Low battery                       Middle light in orange turns solid
In home mode                  Home button turns solid
In cleaning mode              Middle light in green turns solid
In edge mode                   Middle light in green turns solid
In spot mode                   Spot button turns solid

Remote control operation

Remote control operation

Remote control operation 1

Note:
1. Place two AAA batteries into the remote control.
2. Remove batteries if the remote control will not be used for a long time.

Product Operation

Getting started
  1. Place the charging dock on the floor and plug in the adapter. Signal light on charging dock will tum solid.
    Note: Put charging dock against a wall and remove obstacles about 1 meter on both sides and about 2 meters in front.Operation

  2. Display panel will flash after power switch (near power socket) is turned on. (If no command is received, the robot will switch to sleep mode after 45 seconds.)
    Note:
    A. Always keep the power switch on, otherwise the robot will not work.
    B. If power switch is turned off, all scheduled cleaning will be lost.
    Caution: Before charging the robot, make sure the power switch is turned on, or the robot will not be charged.

  3. Robot can be recharged by:
    A. plugging into an outlet;
    B. pressing O[] button on remote control – the robot will return to charging dock for auto recharge.Operation 1
    Extending battery life:
    A. Before first use, charge the robot overnight. When charging is finished, light at main button will turn off.
    B. Always place the robot on charging dock that is connected to power.
    C. If the robot will not be used for a long time, fully recharge the robot and turn the power switch off before storing it in a cool, dry place.

  4. Auto charging
    The robot will automatically return to the charging dock when its battery runs low.

Start/Pause/Sleep

Sleep mode: robot is not working, light at button is off and power switch is on.
Selected mode: robot is not working, green light at button flashes.
Cleaning mode: robot is working, green light at button turns solid.

  1. Start
    A. Make sure the power switch is turned on.
    B. Press button on robot or remote control to start cleaning.
    Nate: If robot is in sleep mode, press button to reactivate it.
    Press button again to start the operation.

  2. Pause
    Press button on robot or remote control to change robot from Clean
    mode to selected mode.
    Nate: When robot is paused, press button to resume the operation.

  3. Sleep
    To switch the robot from selected mode to sleep mode:
    A. Press and hold button on robot for 3 seconds.
    B. Robot automatically enters sleep mode if no command is received after 15 seconds.

Schedule

You can preset a cleaning routine for your robot.
Note: Reset the clock and reschedule a cleaning cycle after replacing battery. Robot will only start cleaning automatically after the clock and schedule are set.

Set the clock

  1. Point the remote control at robot (make sure the power switch is on).
  2. Press button and adjust to your local time.
  3. Press button again to save the setting.
  4. Turn off power switch on robot to cancel the schedule.

Set a schedule
Robot starts a cleaning schedule only when its power switch is on.

  1. Point the remote control at robot.
  2. Press button and adjust time with direction buttons.
  3. Press button to save the setting.
  4. Turn off the robot to cancel the schedule.

Note: Successful clock and schedule settings will be confirmed by a “beep” sound. Reset the schedule if there is no sound confirmation.

Cleaning modes
  1. Auto cleaning
    In Auto Cleaning mode, robot automatically cleans the areas it can reach.
    Note: Press button on robot or remote control to start Auto Cleaning. Operation 2

  2. Spot cleaning
    • Point remote control at robot and press button while it is cleaning. Robot will clean around a circular route and return to Auto Clean mode after Spot cleaning is finished.
    • Point remote control at robot and press button when robot is in selected mode. Robot will clean around a circular route and return to selected mode after Spot cleaning is finished.Operation 3

  3. Edge cleaning
    To start edge cleaning, put the robot near the edge of a wall and press IQ] button on remote control.
    Note: Edge cleaning will automatically stop if the robot cannot detect any edges. To stop edge cleaning manually, press button. Operation
4

Maintenance

Side brushes
Clean the side brushes when they get dirty. Replace them if they are damaged.
Note: When replacing the side brushes, make sure they are installed according to the “L” and “R” marks on both sides of the brush and the base of the robot.

Dustbin and filter
Follow the below steps to empty and clean the dustbin after each use.

• Take out the dustbin and clean dust or debris in the suction opening.
• Clean the high performance filter after 15-30 days of use. Replace it no more than 6 months of use.
• Do not reinstall the high performance filter and primary filters when they are still wet.
• Replace the high performance filter and primary filter if needed.Maintenance

Cliff sensors and auto charging pins
Gently clean the sensor lens and auto charging pins with a soft dry cloth.
Note: Charging pins need to be cleaned if they become dirty.Maintenance
1

Front wheel
Make sure the front wheel is clean to avoid lowered cleaning performance:Maintenance 2

(1) Pull the wheel up and out vertically and clean it. Also check if the gasket is worn.
(2) Ensure that the gasket is properly installed after cleaning the front wheel.

Troubleshooting

Error codes
The robot will remind you by beeping when it is malfunctioning.

Short tones

NO. Tone Possible Cause What to do
01 Wheels or side brushes problems Check wheels and side brushes
02 •• Cliff sensor or bumper sensor failure •   Clean cliff sensor

•   Gently shake the bumper to

check if there’s anything stuck in it

03| •••| Robot gets stuck| Pick up robot and restart

Note: If none of the above solutions works, try the following:

1. Turn power switch off and on to reset the robot.
2. If resetting doesn’t help, contact the seller for repair service.

Error symptoms
Symptoms Possible Cause Solution
Circle around a small areo Side wheels are jammed –  Remove hair and debris

from side wheels

–  While reinstalling, push the wheels in and out to make sure they can rotate freely

–  Restart robot in another spot

Keep moving backward| A Cliff sensor is dirty or broken| Check cliff sensor lens

Clean or replace it if needed

Bump into obstacles repeatedly| The bumper is stucked| –  Tap the bumper 10-20 times to remove debris lodged in it

–  Loosen the screw of the bumper

Working time shortened| –  Battery capacity dropped

–  Robot is not fully charged

| –  Replace battery

–  Recharge robot

CLEAN

button light is off while charging

| –  Hair or small debris stuck in charging pins

–  Robot is not properly

connected to charging pins

| –  Clean charging pins

–  Check if robot is connected to charging pins

Pick up less dirt and debris| Filter is dirty or wet| Clean or replace filter
Spit out litter| Dustbin is full| Empty the dustbin
Robot doesn’t start at scheduled time| –  Schedule was not saved successfully

–  Schedule was canceled after you restarted robot

–  Power Switch is off

–  Battery is low

– Debris jammed in components

| –  Reset schedule. Wait for a beep to confirm completion of scheduling

–  Turn on the power switch on robot

–  Keep robot’s power switch on and put it on charging dock to make sure robot is fully charged for the next job

–  Turn off the power switch on robot and empty the dustbin

–  Clean side brushes and main brushes

Product Specifications

Classification Specification Detail
Mechanical Diameter 300mm
Height 77mm
Net weight 2.16kg
Electrical Voltage 14.4V-14.8V
Battery type Li-ion 2600mAh
Power 22W
Charging type Auto / Manual
Cleaning Capacity of dustbin 0.3L
Cleaning modes Auto/Spot/Edge/Schedule
Duration per recharge About 280 mins
Duration per cleaning Up to 90 mins
Main Body Button Mechanical Button

Remark: The storage temperature of this product is between -l0°C and 40°C.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals