ZACO A4S Robotic Vacuum Cleaner User Manual

June 6, 2024
ZACO

ZACO A4S Robotic Vacuum Cleaner User Manual

ZACO A4S Robotic Vacuum Cleaner User Manual

www.zacorobot.eu

Thank you for choosing ZACO A4s robotic vacuum cleaner! You’ve joined millions of people to get cleaning done robotically.

This user manual helps you to keep your robot performing at its best. Please take a few moments to read through it.

You are entitled to the exclusive benefits once you register
your robot at www.zacorobot.eu/register:
– Access to ZACO 24-hour online customer support;
– Get first-hand updates, including new model launch and exclusive discounts.

As a registered user, you could also share your robotic cleaning experience with us. ZACO listens and makes product improvements based on your valuable feedbacks.

If you have any questions, please contact our customer service for assistance or visit www.zacorobot.eu for more information.

Enjoy automated home cleaning performed by ZACO A4s!

ZACO Customer Service
Customer Service Number:
00800-42377961 (European Free Call)
0209-513038-383 (Direct Line DE)
Email: support@zacorobot.eu

Important notes

A4s contains electronic parts. Do NOT put it in water or spay it with water. Clean the robot with a dry cloth only.

Where to start

  • Place the charging dock against a wall in an open area. Do not put it near a door or steps.
  • Before cleaning begins, clear up excessive objects on the floor (e.g. cables, bar stools, etc.).
  • Choose MAX mode to clean areas with accumulated dust.

For best performance

  • Remove the main brush. Clean the bristle ends and the roller twice a week. (Figure 1)
  • Remove the front wheel with a screwdriver. Remove hair in the wheel cavity and axle twice a week. (Figure 2)
  • Empty the dustbin and clean filter and bristle brush after each use. Replace filter every month.

ZACO A4S Robotic Vacuum Cleaner User Manual - Fig 1,2

Safety Instructions

Before using the robot, please read and follow the below safety instructions and precautions.

  • Read through this user manual carefully before using the robot.
  • Retain this user manual.
  • Any operation that is not described in this user manual may injure the users or cause product damage.

WARNING

  1. Only certified technicians may disassemble the robot. Users must not disassemble or repair the robot.
  2. Use factory authorized adapter only. Using nonspecific adapter may cause electric shock fire or robot damage.
  3. Do not touch the power cord, plug or adapter with wet hands.
  4. Do not allow clothes or any part of your body to be drawn into the robot’s wheels.
  5. Do not place the robot near cigarette, lighter, matches or other flammables.
  6. Clean the robot after charging finishes.
  7. Do not over-bend the power cord or pressure the power cord with heavy or sharp objects.
  8. Do not use the robot outdoor.
  9. Do not sit on the robot or attach any object on it.
  10. Do not use the robot on wet floors.
  11. Before using the robot, remove all fragile objects (textile, glass, lighting, etc) and other objects that could be caught in the brushes or suction opening (cords, clothing, papers, drapes, blinds, etc).
  12. Do not place the robot where it could easily fall off (tables, chairs, etc).
  13. Turn off the power switch during transportation or when the robot will not be used for a long time.
  14. To avoid battery damage, check if the adapter and outlet are properly connected before using the robot.
  15. To avoid tripping, make sure everyone in the house knows the robot is working.
  16. Do not use the robot when the dustbin is full.
  17. Use the robot in environment between -I0°C and 50°C.
  18. Do not place the robot in high-temperature environment.
  19. Battery must be removed from the robot before the battery is scrapped.
  20. Disconnect electricity supply before removing the battery.
  21. The battery is to be disposed of safety according to local regulations.

NOTE: This product should not be used by children, mentally challenged people or people who lack related experience and knowledge (unless they are under proper supervision).

Product Parts

Main body and accessories

ZACO A4S Robotic Vacuum Cleaner User Manual - Main body and
accessories

Robot anatomy

ZACO A4S Robotic Vacuum Cleaner User Manual - Robot
anatomy

Charging dock

ZACO A4S Robotic Vacuum Cleaner User Manual - Charging
dock

CLEAN button status signals

ZACO A4S Robotic Vacuum Cleaner User Manual - Clean button status
signals

Remote control

ZACO A4S Robotic Vacuum Cleaner User Manual - Remote
controlZACO A4S Robotic Vacuum
Cleaner User Manual - Remote control

How to Use

1. Getting started

1>. Place charging dock on the floor and plug in adapter. Signal light on charging dock will tum solid.

Note: Put charging dock against a wall and remove obstacles about 1 meter on both sides and about 2 meters in front.

ZACO A4S Robotic Vacuum Cleaner User Manual - Place charging dock on the
floor and plug in adapter

2>. Display panel will flash after the power switch (near the power socket) is turned on.
(If no command is received, the robot will switch to sleep mode after 45 seconds)

Note:
A. Always keep the power switch on, otherwise the robot will not work.
B. If power switch is turned off, all scheduled cleaning will be lost.

Caution:
Before charging the robot, make sure the power switch is turned on, otherwise the robot will not be charged.

3 >. Robot can be recharged by:
A. Plugging into an electrical outlet;
B. Pressing ( 1§)-) button on remote control – the robot will return to charging dock for auto recharge.

ZACO A4S Robotic Vacuum Cleaner User Manual - Robot can be
recharged

Extending battery life:
A. Before first use, charge the robot overnight. When charging finishes, light at AUTO button will turn off.
B. Always place the robot on the charging dock that is connected to power.
C. If the robot will not be used for a long time, fully recharge it and turn off the power switch before storing it in a cool, dry place.

4 >. Auto charging
Robot will automatically return to charging dock when battery runs low.

2. Start/Pause/Sleep

Sleep mode: robot is not working, light at AUTO button is off and power switch is on.
Selected mode: robot is not working, green light at AUTO button flashes.
Cleaning mode: robot is working, green light at AUTO button turns solid.

l >. Starting up
A. Make sure the power switch is on.
B. Press button on robot or button on remote control to start cleaning.

Note: If robot is in sleep mode, press button to recover it from sleep mode.
Press button again to start the cleaning cycle.

2 >. Pause
Press button on robot or button on remote control to change from Clean mode to selected mode.

Note: When robot is paused, press button to resume the cleaning cycle.

3 >. Sleep
Change from selected mode to sleep mode:
A. Press and hold button on robot for 3 seconds.
B. Robot automatically enters sleep mode if no command is received after 45 seconds.

3. Schedule

1>. Point the remote control at robot and press CLEAN button to recover robot from sleep mode. You will hear a beep.
2>. Adjust the “clock” on remote control to display local time.
A. Press CLOCK and set time with direction buttons.
B. Press CLOCK again to save the setting.

Note: When scheduling a cleaning cycle, keep the remote control close to robot for better signal reception.

3>. Point the remote control at robot, and set PLAN time to start cleaning.
4>. After setting the time, press PLAN button on remote control to save the schedule. Successful scheduling will be confirmed by a “beep” sound.

Note:

  1. Do not place charging dock on carpet.
  2. Make sure the robot is turned on after scheduled cleaning is set.

5>. How to cancel the schedule?

  1. To cancel a schedule, turn off the power switch off on the robot.
  2. Restart the robot.

Successful time and schedule settings are confirmed by a beep sound. If there is no sound confirmation, it means the settings are not saved.

4. Cleaning mode

l >. Auto cleaning
In Auto cleaning mode, robot automatically cleans the areas that it can reach.

Note: Press button on robot or button on remote control to start
Auto cleaning.

2 >. Spot cleaning

  • Press Spot button on remote control while robot is working. Robot will clean around a circular route and return to Auto Clean mode after Spot cleaning is finished.
  • Press Spot button on remote control while robot is in selected mode. Robot will clean around a circular route and return to selected mode after Spot cleaning is finished.

3 >. Edge cleaning
To start edge cleaning, put robot near the edge of a wall and press EDGE on remote control.

Note: Edge cleaning will automatically stop when robot cannot detect any edges. To stop edge cleaning manually, press CLEAN button.

4 >. Mini-Room mode
Press CLEAN button twice on robot or remote control to switch from Sleep mode to MINI-room mode, which is designed for small space or single room cleaning.

Maintenance

1. Side brushes

Clean the side brushes when they get dirty. Replace them if they are damaged.

Note: When replacing the side brushes, make sure they are installed according to the “L” and “R” marks on both sides of the brush and the base of the robot.

2. Dustbin and filter

Follow the steps below to empty and clean dustbin after each use.

  • Take out dustbin and clean dust or debris in the suction opening.
  • Clean filter after 15-30 days of use. Replace it no more than 6 months of use.
  • Do not reinstall filter and primary filter when they are still wet.
  • Replace dustbin and filters (including filter and primary filter) if needed.

ZACO A4S Robotic Vacuum Cleaner User Manual - Dustbin and
filter

3. Cliff sensors and auto charging pins.

Gently clean the sensor lens and charging pins with a soft dry cloth.

ZACO A4S Robotic Vacuum Cleaner User Manual - Cliff sensors and auto
charging pins

4. Front wheel

Make sure the front wheel is clean and can rotate freely to avoid lowered cleaning performance:

  1. Pull the wheel up and out vertically and clean it. Also check if the gasket is worn.
  2. Make sure the gasket is properly installed after cleaning the front wheel.

ZACO A4S Robotic Vacuum Cleaner User Manual - Front
wheel

Product Specifications

ZACO A4S Robotic Vacuum Cleaner User Manual - Product
Specifications

Remark: The storage temperature of this product is between -20°C and 60°C. Clock or schedule setting is confirmed with a beep sound. Setting is unsuccessful if there is no sound confirmation.

Troubleshooting

The robot will remind you by beeping or erratic movements when it is malfunct1ornng.

ZACO A4S Robotic Vacuum Cleaner User Manual -
Troubleshooting ZACO A4S Robotic
Vacuum Cleaner User Manual - Troubleshooting

For more details, please visit www.zacorobot.eu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals