PHILIPS EasyKey 9000 Series Push-pull Smart Door Lock User Manual

PHILIPS EasyKey 9000 Series Push-pull Smart Door Lock

Important information

Safety

• Before using Philips EasyKey, please read and understand all instructions. Damage caused by non-compliance with the instructions will not be covered by warranty.
• Use only the manufacturer-specified accessories/components.
• Use only the alkaline batteries the product is equipped with, or use the same specification type of alkaline batteries.
• Do not forcibly disassemble this product to avoid triggering an alarm or damaging the product.
• Do not scrape the fingerprint sensor with sharp objects, otherwise it may cause permanent damage.
• Do not expose products to environments where there is water leakage or splashing.
• Do not expose the product to corrosive substances to prevent damaging the protective cover.
• Do not hang objects on the handle, in case it might affect the normal use of the lock.
• Pleae clean the product with a soft cloth.
• Do not remove the battery during setting up and operating.
• Please let a professional technician to install the door lock and follow the installation guidelines provided.Do not disassemble the lock by yourself. Keep the relevant sealed stickers properly. Do not easily disclose the password information.
• Please modify the default master PIN code immediately after finishing installing and debugging, and keep the mechanical key properly.
• Please replace all the batteries immediately if there is a low battery alarm. Please make sure to correctly match the poles (+/-) when installing the batteries.

Caution

• Do not place the battery near fire sources to avoid explosion.
• Do not use any emergency power supply that does not meet the safety requirements to power up the product.
• Do not connect the 2 poles of the batteries with metals to avoid short circuit which may lead to an explosion.
• Please make sure any component replacement is executed by Philips, Philips authorized service center or professional technicians.
• Do not use accessories or parts that have been produced by other manufacturers or have not been specifically recommended by Philips. The use of such accessories and parts may void your warranty.

Disposal of used products and batteries

• You can have your locks reclaimed at Philips authorized service centers. You will receive corresponding compensation if your products meet our conditions.
• Please familiarize yourself with the local electronic product collection system.
• Please follow local regulations and do not discard used products into ordinary household waste.
• Proper disposal of used products can help to avoid potential negative impacts on the environment and human health.
• Batteries must not be disposed of with ordinary household waste.
• Please familiarize yourself with the local regulations on batteries classification recycling. Disposing of batteries properly can help avoid a negative impact on the environment and human health.

Easykey Installation

Packing List
This packing list is for reference only. Please refer to the actual packing items.

Exploded Views

1. Deco Cover
2. M6 Connecting Screw (X1)
3. Upper Mounting Plate Set (X1)
4. M6 Connecting Screw Tube (X2)
5. Outside Escutcheon (X1)
6. Battery Cover
7. M6 Anchor Screw (X2)
8. Inside Escutcheon (X1)
9. Compressed Spring (X2)
10. Square Shaft (X2)
11. M5 Connecting Screw (X4)
12. Mounting Plate (X1)
13. Mortise (X1)
14. M5 Connecting Screw Tube (X4)

Pre-install Instruction
This product can be installed on 4 types of opening directions: left-out pull, right-in push, right-out pull and left-in push.

Attention

1. Please choose proper installation kit as per the door thickness.
2. The default installation kit is applicable for a door thickness of 38-60mm, if your door thickness does not within this range, please feel free to contact us.

Installation Steps

1. To drill the needed holes in the door as per the drilling template,then mount the mortise on the door frame.
2. Fasten the 4 anchor screws in the mortise.
3. To install the connecting screw tubes on the outside escutcheon, and put the compressed spring and square shaft accordingly into the square shaft holes.
4. Pass the connecting cable through the hole above the door. Align the square shaft of the outside escutcheon with the two rotary holes on the mortise, then insert the square shaft into the rotary holes, so that the outside escutcheon is close fit in the outside door.
5. First fix the mounting plate against the inner surface of the door, and fasten it with 4 M5 connecting screws, and then fix the upper mounting plate with M6 connecting screws.
6. Put the compressed spring and square shaft into the square shaft hole of the inside escutcheon accordingly.
7. Insert the outside escutcheon connection cable and the motor cable into the corresponding sockets on the inside escutcheon, and then connect the front and rear Bluetooth connecting cables, and then align the square shaft of the inside escutcheon with the two rotary holes on the mortise, then insert the square shaft into the rotary holes, so that the inside escutcheon is close fit in the inside door.
8. Unscrew the deco cover by turning it counterclockwise, and press the battery cover button to remove the battery cover. Then the two M6 mounting screws can be installed to fasten the inside escutcheon.
9. Turn clockwise to install the deco cover, install the battery, put the battery cover back, and after attach the strike, the installation of the smart lock is complete.
10. To check whether if the rotary knob, mechanical keys, and all other components could be used normally.

Get to know Your EasyKey

Outside Escutcheon

Inside Escutcheon

-ion Module Interface

6| OPEN/CLOSE Button
7| Rotary Knob
8| Battery Cover

How to set up your EasyKey

Pre-install Instruction

• There are two modes for the EasyKey System: general mode and dual verification mode.

• General Mode: Dual Verification Mode

• Unlock with any of the registered identify methods:
  Unlock with any two of the registered identify methods among PIN code, Key Tag, and Fingerprint

• User Code
  When you want to delete one single user record, you could delete it in the system by deleting its user code.

• You could fill in the below blank sheet with the user information in case you might need to check or review in the future.
  Number| Name| Fingerprint| PIN Code| Card
  ---|---|---|---|---
  00|  |  |  |
  01|  |  |  |
  02|  |  |  |
  03|  |  |  |
  04|  |  |  |
  05|  |  |  |
  06|  |  |  |
  07|  |  |  |
  08|  |  |  |
  09|  |  |  |

• Icon annotation

Attention

1. Press [*] key to return to the previous menu.
2. The default master PIN code is 12345678

• How to enter into Master Mode

Press [#] before inputting any other numbers. After hearing a voice prompt of “Enter master PIN code”, enter your master PIN code and confirm with [#]. Then you are in master mode.

Modify master PIN code

Enter the new master PIN code and confirm with [#] again. Re-enter the same master PIN code and confirm with [#]. After hearing a voice prompt of “Succeeded”, press [*] to return to previous menu until you finally exit master mode.

User settings

Add a user PIN code

Enter a user PIN code of 6 to 12 digits and confirm with [#]. Then re-enter the user PIN code and confirm with [#]. After hearing a voice prompt of “Succeeded”, press [*] until you exit master mode.

Add a one-time User PIN Cod

Enter a one-time user PIN code of 6 to 12 digits and confirm with [#]. Then re-enter the one-time user PIN code and confirm with [#]. After hearing a voice prompt of “Succeeded”, press [*] until you exit master mode.

Add a Fingerprint

Place your finger against the sensor. After hearing a voice prompt of “Take away your finger and enroll again”, please take away your finger and re-place it against the sensor. After hearing a voice prompt of “Succeeded”, press [*] until you exit master mode.

Add a Key Tag

Place the key tag against the card reader until you hear a beep. After hearing a voice prompt of “Succeeded”, press [*] until you exit the master mode.

Delete a User Record

Delete a single User PIN Code

Enter a user code (code: 00-09) of 2 digits and confirm with[#]. After hearing a voice prompt of “Succeeded”, press [*] until you exit the master mode.

Delete All User PIN Codes

Enter [3] to delete a user record, then enter [1] to delete a user PIN code, and then enter [2] to delete all user PIN codes. After hearing a voice prompt of “Succeeded”, press [*] until you exit the master mode.

Delete all One-time PIN Codes

Delete a Fingerprint

Enter the 2-digit [user number] (00-99) of the fingerprint that is to be deleted and confirm with [#]. After hearing a voice prompt of “Succeeded”, press [*] until you exit the master mode.

Delete All Fingerprints

Delete a Key Tag

Delete All Key Tags

System Initialization

Remove the battery cover, then double press the [RES] hole with a sharp object, after hearing a voice prompt of “Restoring to default settings”, all user information will be emptied.

System Settings

Language Settings Attention

The default language is English.

Volume Settings

Attention: The default volume is “high volume”.

Switch to Dual Verification Mode

Extended Functions

Attention : The extended functions are optional.

System Query

Security Code Query

Attention : Directly input 400# could enter into system query.

Local Query

Bluetooth Settings

Attention

1. Directly input 403# to enable Bluetooth, and input 404# to disable Bluetooth.
2. When the Bluetooth is off, please press [1] to enable Bluetooth.
3. When using the newly updated EasyKey App to bind with the smart lock, users could follow up the chapter of “Add a device” to finish the binding process.

How to use your EasyKey

Unlock | Unlock from outside

1. Touch and wake up the keypad, then enter a registered user PIN code and confirm with [#].

2. After hearing a voice prompt of “Door opened”, push or pull the handle to open the door.

3. Place the finger of which the fingerprint has been registered against the sensor.

4. After hearing a voice prompt of “Door opened”, push or pull the handle to open the door.

5. Place the key tag/card that has been successfully registered properly against the card reader.

6. After hearing a voice prompt of “Door opened”, push or pull the handle to open the door.

Unlock | Unlock from Inside

• Philips EasyKey employs indoor fast opening mortise. You can unlock from inside by rotating the rotary knob.
• Double press the [OPEN/CLOSE] functional button within one second, then push or pull to unlock.
• Features with an infrared sensor on the handle, when the sensor is triggered, hold the handle’s sensor modules on both the front and rear side simultaneously,you could easily unlock the door.

Lock | Auto/Manual Mode

Lock from Outside

When the door is under auto mode, the latch bolt will be popped up after closing the door, and there will be a voice prompt of “Door Close”.

When the door is under manual mode, the latch bolt won’t pop up after closing the door. Only after a successful verification among any of the registered identity methods (PIN Code/Key Tag/Fingerprint), the latch bolt will pop up, and there will be a voice prompt of “Door Close”. When it is under manual mode and the door is closed, waking up the outside escutcheon and unlock the system could directly open the door.

Lock from Inside

When the door is under auto mode, the latch bolt will be popped up after closing the door, and there will be a voice prompt of “Door Close”.

When the door is under manual mode, the latch bolt won’t be popped up after closing the door. Click on [CLOSE] and the latch bolt will be popped up. After successfully locking the door, the system will generate a voice prompt of “Door Close”.

Inside Deadlock

When the EasyKey is locked, long-press the [CLOSE] button, after the indicator flashes once in red, and there will be a voice prompt of “Inside deadlock enabled”.

Attention: Under inside deadlock mode, all functions of the outside escutcheon will be locked. If you try to wake up the system manually, the keypad area will display the combination of “15937(X)” and there will be a voice prompt of “Inside deadlock enabled” reminding you that the door has been deadlocked from inside. Under deadlock mode, all operations of the outside escutcheon are disabled. Master PIN code verification or mechanical key opening is required to release the door from deadlock mode.

Mechanical Key Opening

1. Cut the box and take out the mechanical keys. Push the cover aside and reveal the key itself
2. Insert the key into the keyhole and keep the key and key shell vertical to each other. Rotate the key shell towards the handle for 90°until it closes to the door surface.
3. Rotate the key shell downwards for 180° to make it parallel to the ground. Then rotate it horizontally towards the handle to unlock the door.

Attention : It is suggested you not to use the mechanical key for daily unlocking. Use the key for emergencies only, in case the battery is dead, forget the PIN code, or the system fails to work properly.

 Other Functions

Indoor Infrared Sensor Unlocking

Attention : When the infrared sensor unlocking is disabled, the indoor inductive unlocking is inactive. When you touch the front and rear of the inductive position on the handle, the red light will light up to remind you that the indoor inductive unlocking is off.

Function:
With indoor infrared sensor unlocking, you could easily unlock the door from inside.
How to use:
Features with the infrared sensor on the handle, when the sensor is triggered, hold the handle’s sensor modules on both the front and rear inductive position simultaneously, you could easily unlock the door.
Enable/Disable：
When the infrared sensor unlocking is disabled, long-press the [OPEN] / [CLOSE] button at the same time to turn on the function, and the green light will flash quickly; When the infrared sensor unlocking is enabled, long-press the [OPEN] / [CLOSE] button at the same time to turn off the function and the red light will flash quickly.

Restore to Default Settings

Mute Mode

Functions:
Use only one button to mute the lock by turning off the voice guide. Applicable to the scenes where you don’t want to disturb your family.
How to use:

1. Mute: When the system is awake, long-press the [Mute] button for 2 seconds to enter one-time mute mode. The button will glow green.
2. Unmute: When the system is awake, long-press the [Mute] button for 2 seconds to restore the voice guide. The button will glow white.

Outside Forced Lock

Functions:
Unlocking from inside will trigger an alarm.
How to use:
After the door is successfully locked, long press the button for 2 seconds to enter the outside forced lock mode.

Attention : Enabling the outside forced lock function will not affect unlocking from outside.

The use and meanings of indicators

Lock Status Indicator

The meanings of different light colors
Blue : When the system wakes up, the light will glow blue, indicating that you can operate the lock.
Green : When the door is unlocked, the light will glow green, indicating that the door is open.
Red : When the door is locked, the light will glow red, indicating that the door is close.

Low Battery Voltage Indicator

The meanings of different light colors
Red : After waking up, the system will run an automatic examination of the battery voltage. If the voltage is too low, the light will flash in red and there will be a voice prompt of “Low battery voltage. Please replace all batteries”.

Outside Forced Lock Indicator

The meanings of different light colors
White:

1. When the door is locked, it will glow in white, indicating that you can enable the outside forced locking.
2. If you have enabled the outside forced locking, when the system wakes up, the light will glow in white, indicating this function is in use.

Mute mode indicator

The meanings of different light colors

1. White: Indicates the mute mode is off.
2. Green:Indicates the mute mode is on.

Inside Deadlock Indicator

When the door is under inside deadlocking, the digital functions of the outside escutcheon will be locked. If the system wakes up manually, the keypad will show the combination of “15937 (X)” with a voice prompt of “inside deadlocking enabled”.

System Locked Indicator

If any of the verification methods among fingerprint, password, or card/key tag has scanned to be incorrect and the number of consecutive incorrect entries reaches 5 times within 5 minutes, the EasyKey will be locked for 3 minutes.

Attention: Only under any of the verification methods above or the keypad is wakened up, will the prompt be seen.

[OPEN/CLOSE] Indicator

The meanings of different light colors

1. With 2 flashes in red: indicates the door is locking.
2. With 2 flashes in green: indicates the door is unlocking.
3. With 1 flash in red: indicates the door is deadlocking.

Infrared Sensor Opening Indicator

The meanings of different light colors

1. Fast flashing in green: Infrared sensor opening is on.
2. Fast flashing in red: Infrared sensor opening is off.

Troubleshooting

Alarm Types and Modes

Inside Unlocking Alarm Under Outside Forced Lock

Triggering : If the lock is under outside forced lock mode, unlocking from inside will trigger the alarm.
Alarm mode: Continuously repeated alarms.
Turning off : The alarm can be turned off by successful verification of any type.

Low Battery Voltage Alarm reminds you of replacing the batteries in time

Triggering : After waking up, the system will run an automatic examination on the battery voltage. If the voltage is too low, the lock will give an alarm with a voice prompt of “Low battery voltage. Please replace all batteries”.
Alarm mode: A voice prompt of “Low battery voltage. Please replace all batteries” during unlocking.
Turning off: The alarm will be automatically turned off.

Anti-dismantling Alarm

Triggering 1 : The door is pried open and the sensor latch bolt pops up.
Alarm mode: Continuously repeated alarms.
Turning off: The alarm can be turned off automatically or by a successful verification.
Triggering 2: The door is pried open and there is no close fit in the door.
Alarm mode: Continuously repeated alarms.
Turning off: The alarm can be turned off automatically, by a successful verification from outside or normal unlocking from inside.

Deadbolt Abnormality Alarm

Triggering : The deadbolt works abnormally, fails to lock or unlock the door.
Alarm mode: Continuously repeated alarms.
Turning off: The alarm will be automatically turned off.

How to apply emergency power supply

When the battery voltage is insufficient, and the door cannot be opened from the outside, you can power up the lock through the Micro USB interface by using a 5V power bank as an emergency power supply. After opening the door, please replace the batteries immediately. In case of a system crash and it’s impossible to open the door from outside, please press the [RES] button and then release it to reboot automatically.

How to replace batteries

The lock is powered by four 1.5V alkaline batteries. There are two sets of working power stations in the battery cabinet. Eight batteries can put in to extend battery life and reduce battery replacement frequency. The battery cabinet locates at the bottom end of the inside escutcheon. By pushing the cover upwards, you can remove it and replace the batteries.

Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of Shenzhen Conex Intelligent Technology Co., Ltd. and Shenzhen Conex Intelligent Technology Co., Ltd. is the warrantor concerning this product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>