ALC AWF54 Outdoor Pan and Tilt Wi-Fi Camera User Guide

ALC AWF54 Outdoor Pan and Tilt Wi-Fi Camera

Getting Started

What You Will Need:
Philips Screwdriver, 2.4GHz Wi-Fi network, network name and password.

where should I position my Pan & Tilt camera?

Knowing where to place your pan ‘n tilt camera is very important for optimal surveillance

When Considering Locations

• DO:
  • Position in vulnerable areas such as: Front Door
  • Back & Side Doors
  • Garage & Drivewa
  • Interior Common Areas
• DON’T
  • Position camera in ways that violate your neighbor’s privacy
  • Install in areas inside where there is a warranted expectation of privacy, such as bedrooms and bathrooms

For Outdoor Installation

• DO
  • Install camera 8-10 feet from the ground
  • Protect Camera from direct exposure to the elements
• DON’T
  • Point camera directly at the sun, it causes glares and high contrast
  • Position camera where rain gutters, trees and heavy foliage can obstruct views

For Indoor Installation

• DO
  • Take advantage of corners to provide largest possible vantage point
  • Angle for indirect light
• DON’T
  • Position camera directly toward light sources
  • Point camera directly at windows as it can cause reflection issues

Location of Controls

Device Setup

Download the Sight HD App and open it. Use the Set Up Wizard to connect to your Wi-Fi network and follow the steps to finish the installation.

TIP: It is highly recommended to set up your camera to wifi before installing it in its final location After the camera is successfully connected to wifi

1. unplug camera power
2. mount camera unslung bracket

App Download & Wi-Fi Connection

1. From your smart device or tablet, DOWNLOAD and INSTALL the free Sight HD App.

2. Add antenna and plug camera into an electrical outlet (allow the camera up to 90 seconds to startup).

3. Now, LAUNCH the Sight HD App and the Setup Wizard will appear.
   NOTE: Screen shots and icons may vary due to continuous updates to App and software development.

4. Tap + to start the Wizard  and then tap Add Device.

5. Tap New Device and the unit will start searching.
   NOTE: If the mobile device’s Bluetooth is not turned on, a message will appear requesting to have the Bluetooth setting turned on.

6. Select your home network from the menu, and then enter your home network’s Wireless Password. If you get an error, make sure to enter the correct password and repeat.

7. At the next screen enter a New Password/ Security Code twice. Tap SAVE.
   TIP: Remember to write down your new Security Code and save it somewhere safe and easy for you to access.

8. Tap the PLAY icon or preview picture for live video.

Screw the Antenna clockwise into the rear of the camera.

Secure the multi-position Camera Bracket to a stable surface or wall using the four screws. If needed, four anchors are also included. It should be looking good.
Connect the small end of the AC adapter to the camera’s AC-in Plug located at the end of the bracket. You’re almost there. Plug into electrical outlet when ready to install Sight HD App. To Set the Camera’s Home/Default Point: Position the camera where you want for the Home position.
Tap the PTZ icon, then 1 Save. You can add up to two more pre-programmed points. There – you did it!

Good stuff to know

• Tap Snapshot icon to save image to camera roll or gallery

• Tap to Record to MicroSD card (pre-installed)

• Tap and hold the Microphone icon to talk, (sound comes through video camera’s speaker)

• Tap Settings icon from home page to access Advanced Settings and Customizing Features.

• Tap to turn volume ON or OFF in Live View Mode

• PTZ button (Pan & Tilt) allows the user to set 3 preset positions for the camera to move to (includes Home position).

• Smart motion detection push notification alerts

• Tap to RETURN icon to go back to the main page

• Tap to EVENT icon to review recorded files.

Advanced Settings

NOTE: Screenshots and icons may vary due to continuous updates to App and software development.

CAUTION: Do not submerge the camera in the water. STRANGULATION HAZARD: Infants have strangled in power cords. Keep power cords more than 3 feet away from cribs. When using your equipment, always follow basic safety precautions to reduce the risk of fire, electric shock, and injury to persons. Illustrations are for reference only. Actual product specifications may vary.

For additional precautions and product information, please see the owner’s manual on the AWF54 product page.

For detailed installation and setup, please refer to the extended User’s Guide available on the AWF54 product page on our website ALCwireless.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>