Ashdown Slide In Gas True Convection Studio Range User Manual

Ashdown Slide In Gas True Convection Studio Range

STUDIO JNR

FEATURES

1. Input – a 1/4” Jack Socket for use with your instrument

2. Volume – A rotary control to adjust the overall output of the amp.

3. Bass – A rotary control to adjust the amount of Bass +/- 15dB.

4. Middle – A rotary control to adjust the amount of Middle +/- 15dB.

5. Treble – A rotary control to adjust the amount of Treble +/- 15dB.

6. Headphones – 1/4” Headphone Jack Output (this actively mutes the speaker for silent practice).

7. Line In – For use with a line level instrument or audio device such as an MP3 player

8. On – light indicates the amplifier is powered.

9. Power Switch – Turn your amp on or off

10. IEC Power input – a fused IEC power inlet for use with the supplied cable

STUDIO 8

FEATURES

1. Input – a 1/4” Jack Socket for use with your instrument

2. Volume – A rotary control to adjust the overall output of the amp.

3. Bass – A rotary control to adjust the amount of Bass +/- 15dB.

4. Middle – A rotary control to adjust the amount of Middle +/- 15dB.

5. Treble – A rotary control to adjust the amount of Treble +/- 15dB.

6. Line Mix – A rotary control to mix the line level signal with your instrument

7. Line In – For use with a line level instrument or audio device such as an MP3 player

8. On – light indicates the amplifier is powered.

9. Headphones – Mini Headphone Jack Output.
   

10. IEC Power input – a fused IEC power inlet for use with the supplied cable

11. Power Switch – Turn your amp on or off

12. Speaker Mute – To mute the speaker for use with headphones

STUDIO 10

FEATURES

1. On – light indicates the amplifier is powered.

2. Shape – A switchable pre-shape EQ.

3. Pre-Gain – A rotary control to set the input sensitivity of the amp in conjunction with your instrument.

4. Drive – A rotary control to adjust the amount of tube emulated overdrive.

5. Bass – A rotary control to adjust the amount of Bass +/- 15dB.

6. Lo-Mid – A rotary control to adjust the amount of Lo-Mid +/- 15dB.

7. Middle – A rotary control to adjust the amount of Middle +/- 15dB.

8. Hi-Mid – A rotary control to adjust the amount of Hi-Mid +/- 15dB.

9. Treble – A rotary control to adjust the amount of Treble +/- 15dB.
   

10. Volume – A rotary control to adjust the overall output of the amp.

11. Headphones – 1/4” Headphone Jack Output (this actively mutes the speaker for silent practice).

12. Line In – For use with a line level instrument or audio device such as an MP3 player

13. Passive/Active – A -15dB input pad for use with active instruments

14. Input – a 1/4” Jack Socket for use with your instrument

15. Power Switch – Turn your amp on or off

16. IEC Power input – a fused IEC power inlet for use with the supplied cable

STUDIO 12

FEATURES

1. On – light indicates the amplifier is powered.

2. Shape – A switchable pre-shape EQ.

3. Pre-Gain – A rotary control to set the input sensitivity of the amp in conjunction with your instrument.

4. Drive – A rotary control to adjust the amount of tube emulated overdrive.

5. Bass – A rotary control to adjust the amount of Bass +/- 15dB.

6. Lo-Mid – A rotary control to adjust the amount of Lo-Mid +/- 15dB.

7. Middle – A rotary control to adjust the amount of Middle +/- 15dB.

8. Hi-Mid – A rotary control to adjust the amount of Hi-Mid +/- 15dB.

9. Treble – A rotary control to adjust the amount of Treble +/- 15dB.

10. Volume – A rotary control to adjust the overall output of the amp.

11. FX Loop – a TSR Jack is provided for use with a Y cable (tip send ring return).

12. Di – A balanced XLR Di Output.

13. Headphones – 1/4” Headphone Jack Output (this actively mutes the speaker for silent practice).

14. F/S – Footswitch out for use with an FS1single latching footswitch (sold separately) to control the Drive in/out.

15. Line In – For use with a line level instrument or audio device such as an MP3 player

16. Passive/Active – A -15dB input pad for use with active instruments

17. Input – a 1/4” Jack Socket for use with your instrument

18. Power Switch – Turn your amp on or off

19. IEC Power input – a fused IEC power inlet for use with the supplied cable

STUDIO 15

FEATURES

1. On – light indicates the amplifier is powered.

2. Shape – A switchable pre-shape EQ.

3. Pre-Gain – A rotary control to set the input sensitivity of the amp in conjunction with your instrument.

4. Drive – A rotary control to adjust the amount of tube emulated overdrive.

5. Bass – A rotary control to adjust the amount of Bass +/- 15dB.

6. Lo-Mid – A rotary control to adjust the amount of Lo-Mid +/- 15dB.

7. Middle – A rotary control to adjust the amount of Middle +/- 15dB.

8. Hi-Mid – A rotary control to adjust the amount of Hi-Mid +/- 15dB.

9. Treble – A rotary control to adjust the amount of Treble +/- 15dB.

10. Volume – A rotary control to adjust the overall output of the amp.

11. FX Loop – a TSR Jack is provided for use with a Y cable (tip send ring return).

12. Di – A balanced XLR Di Output.

13. Headphones – 1/4” Headphone Jack Output (this actively mutes the speaker for silent practice).

14. F/S – Footswitch out for use with an FS1single latching footswitch (sold separately) to control the Drive in/out.
    

15. Line In – For use with a line level instrument or audio device such as an MP3 player

16. Passive/Active – A -15dB input pad for use with active instruments

17. Input – a 1/4” Jack Socket for use with your instrument

18. Power Switch – Turn your amp on or off

19. IEC Power input – a fused IEC power inlet for use with the supplied cable

20. Tweeter Mute – a simple on/off switch to engage/defeat the on board HF tweeter

STUDIO 210

FEATURES

1. On – light indicates the amplifier is powered.

2. Shape – A switchable pre-shape EQ.

3. Pre-Gain – A rotary control to set the input sensitivity of the amp in conjunction with your instrument.

4. Drive – A rotary control to adjust the amount of tube emulated overdrive.

5. Bass – A rotary control to adjust the amount of Bass +/- 15dB.

6. Lo-Mid – A rotary control to adjust the amount of Lo-Mid +/- 15dB.

7. Middle – A rotary control to adjust the amount of Middle +/- 15dB.

8. Hi-Mid – A rotary control to adjust the amount of Hi-Mid +/- 15dB.

9. Treble – A rotary control to adjust the amount of Treble +/- 15dB.

10. Volume – A rotary control to adjust the overall output of the amp.

11. FX Loop – a TSR Jack is provided for use with a Y cable (tip send ring return).

12. Di – A balanced XLR Di Output.

13. Headphones – 1/4” Headphone Jack Output (this actively mutes the speaker for silent practice).

14. F/S – Footswitch out for use with an FS1single latching footswitch (sold separately) to control the Drive in/out.
    

15. Line In – For use with a line level instrument or audio device such as an MP3 player

16. Passive/Active – A -15dB input pad for use with active instruments

17. Input – a 1/4” Jack Socket for use with your instrument

18. Power Switch – Turn your amp on or off

19. IEC Power input – a fused IEC power inlet for use with the supplied cable

20. Tweeter Mute – a simple on/off switch to engage/defeat the on board HF tweeter

21. Speaker Mute – a simple on/off switch to mute the on board speaker for silent use

22. Speaker Output – An 8 Ohm speaker 1/4” output for use with an extension speaker

SPECIFICATION

Studio Jnr

• Output Power 15watts rms into 8 ohms
• Speaker Unit 1 x 6” Ashdown Driver
• Input Impedance 1 Meg ohm
• Input Signal Range 100Mv to 10v
• E.Q. Passive Bass, Middle, Treble.
• Weight 6Kgs 13.1Lbs

Studio 8

• Output Power 30watts rms into 8 ohms
• Speaker Unit 1 x 8” Ashdown Driver
• Input Impedance 1 Meg ohm
• Input Signal Range 100Mv to 10v
• E.Q. Passive Bass, Middle, Treble.
• Dimensions (mm) H:336* W:360 D:227
• Weight 6.1Kgs 13.4Lbs

Studio 10

• Output Power 60watts rms into 8 ohms
• Speaker Unit 1 x 10” Ashdown Driver
• Input Impedance 1 Meg ohm
• Input Signal Range 100Mv to 10v
• E.Q. Passive Bass, Middle, Treble.
• Dimensions (mm) H:366* W:360 D:302
• Weight 7Kgs 15.4Lbs

Studio 12

• Output Power 100watts rms into 8 ohms
• Speaker Unit 1 x 12” Ashdown Driver
• Input Impedance 1 Meg ohm
• Input Signal Range 100Mv to 10v
• E.Q. Bass, Hi-Mid, Middle, Lo-Mid, Treble
• Dimensions (mm) H:472* W:414 D:357
• Weight 10.3Kgs 22.7Lbs

Studio 15

• Output Power 300watts rms into 8 ohms
• Speaker Unit 1 x 15” Ashdown Driver & Tweeter
• Input Impedance 1 Meg ohm
• Input Signal Range 100Mv to 10v
• E.Q. Bass, Hi-Mid, Middle, Lo-Mid, Treble
• Dimensions (mm) H:526* W:428 D:378
• Weight 11.2Kgs 24.6Lbs

Studio 210

• Output Power 300watts rms into 8 ohms
• Speaker Unit 2 x 10” Ashdown NEO Driver & Tweeter
• Input Impedance 1 Meg ohm
• Input Signal Range 100Mv to 10v
• E.Q. Bass, Hi-Mid, Middle, Lo-Mid, Treble
• Dimensions (mm) H:526* W:428 D:378
• Weight 11.2Kgs 24.6Lbs

www.ASHDOWNMUSIC.COM

References

• Ashdown Engineering - Engineered to Last
• Register Your Product – Ashdown Engineering

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>