Ashdown 10130189 Studio Junior Bass Amplifier User Manual
- June 5, 2024
- Ashdown
Table of Contents
THANK YOU!
FOR PURCHASING
YOUR NEW STUDIO BASS COMBO
REGISTER ONLINE
Please register this product online so we can make sure we give you years of
customer support through our friendly in-house service center. Here is where
you need to visit to register your product:
http://www.ashdownmusic.com/pages/register
WWW.ASHDOWNMUSIC.COM
ASHDOWN ENGINEERING – STUDIO RANGE
INTRODUCTION
The all-new designs feature a new lightweight design using responsibly sourced
poplar-ply wood, providing a light but strong structure for our new combo
enclosures. Today people require our products to be portable yet practical,
which in essence is a task of its own. When designing our new studio line we
discussed a number of different ideas, but the key point was that they needed
to sound as good as they look… So going back to basics we leaned upon one our
tried and tested EQ sections by way of the 5
BAND EQ is featured across our Rootmaster and OriginAL ranges, this EQ opens
up everything you need to establish a great tone straight out of the box, with
everything at 12 O’clock the NEW Ashdown Studio Range sounds as you would
expect from a bass guitar warm yet articulate.
ASHDOWN ENGINEERING – STUDIO JNR
FEATURES
-
Input – a 1/4” Jack Socket for use with your instrument
-
Volume – A rotary control to adjust the overall output of the amp.
-
Bass – A rotary control to adjust the amount of Bass +/- 15dB.
-
Middle – A rotary control to adjust the amount of Middle +/- 15dB.
-
Treble – A rotary control to adjust the amount of Treble +/- 15dB.
-
Headphones – 1/4” Headphone Jack Output (this actively mutes the speaker for silent practice).
-
Line In – For use with a line-level instrument or audio device such as an MP3 player
-
On-light indicates the amplifier is powered.
-
Power Switch – Turn your amp on or off
ASHDOWN ENGINEERING – STUDIO JNR
-
IEC Power input – a fused IEC power inlet for use with the supplied cable
ASHDOWN ENGINEERING – STUDIO 8
FEATURES
-
Input – a 1/4” Jack Socket for use with your instrument
-
Volume – A rotary control to adjust the overall output of the amp.
-
Bass – A rotary control to adjust the amount of Bass +/- 15dB.
-
Middle – A rotary control to adjust the amount of Middle +/- 15dB.
-
Treble – A rotary control to adjust the amount of Treble +/- 15dB.
-
Line Mix – A rotary control to mix the line-level signal with your instrument
-
Line In – For use with a line-level instrument or audio device such as an MP3 player
-
On-light indicates the amplifier is powered.
-
Headphones – Mini Headphone Jack Output.
ASHDOWN ENGINEERING – STUDIO 8
-
IEC Power input – a fused IEC power inlet for use with the supplied cable
-
Power Switch – Turn your amp on or off
-
Speaker Mute – To mute the speaker for use with headphones
ASHDOWN ENGINEERING – STUDIO 10
FEATURES
-
On-light indicates the amplifier is powered.
-
Shape – A switchable pre-shape EQ.
-
Pre-Gain – A rotary control to set the input sensitivity of the amp in conjunction with your instrument.
-
Drive – A rotary control to adjust the amount of tube emulated overdrive.
-
Bass – A rotary control to adjust the amount of Bass +/- 15dB.
-
Lo-Mid – A rotary control to adjust the amount of Lo-Mid +/- 15dB.
-
Middle – A rotary control to adjust the amount of Middle +/- 15dB.
-
Hi-Mid – A rotary control to adjust the amount of Hi-Mid +/- 15dB.
-
Treble – A rotary control to adjust the amount of Treble +/- 15dB.
-
Volume – A rotary control to adjust the overall output of the amp.
-
Headphones – 1/4” Headphone Jack Output (this actively mutes the speaker for silent practice).
-
Line In – For use with a line-level instrument or audio device such as an MP3 player
-
Passive/Active – A -15dB input pad for use with active instruments
-
Input – a 1/4” Jack Socket for use with your instrument
ASHDOWN ENGINEERING – STUDIO 10
-
Power Switch – Turn your amp on or off
-
IEC Power input – a fused IEC power inlet for use with the supplied cable
ASHDOWN ENGINEERING – STUDIO 12
FEATURES
-
On-light indicates the amplifier is powered.
-
Shape – A switchable pre-shape EQ.
-
Pre-Gain – A rotary control to set the input sensitivity of the amp in conjunction with your instrument.
-
Drive – A rotary control to adjust the amount of tube emulated overdrive.
-
Bass – A rotary control to adjust the amount of Bass +/- 15dB.
-
Lo-Mid – A rotary control to adjust the amount of Lo-Mid +/- 15dB.
-
Middle – A rotary control to adjust the amount of Middle +/- 15dB.
-
Hi-Mid – A rotary control to adjust the amount of Hi-Mid +/- 15dB.
-
Treble – A rotary control to adjust the amount of Treble +/- 15dB.
-
Volume – A rotary control to adjust the overall output of the amp.
-
FX Loop – a TSR Jack is provided for use with a Y cable (tip send ring return).
-
Di – A balanced XLR Di Output.
-
Headphones – 1/4” Headphone Jack Output (this actively mutes the speaker for silent practice).
-
F/S – Footswitch out for use with an FS1single latching footswitch (sold separately) to control the Drive-in/out.
-
Line In – For use with a line-level instrument or audio device such as an MP3 player
-
Passive/Active – A -15dB input pad for use with active instruments
-
Input – a 1/4” Jack Socket for use with your instrument
ASHDOWN ENGINEERING – STUDIO 12
-
Power Switch – Turn your amp on or off
-
IEC Power input – a fused IEC power inlet for use with the supplied cable
ASHDOWN ENGINEERING – STUDIO 15
FEATURES
-
On-light indicates the amplifier is powered.
-
Shape – A switchable pre-shape EQ.
-
Pre-Gain – A rotary control to set the input sensitivity of the amp in conjunction with your instrument.
-
Drive – A rotary control to adjust the amount of tube emulated overdrive.
-
Bass – A rotary control to adjust the amount of Bass +/- 15dB.
-
Lo-Mid – A rotary control to adjust the amount of Lo-Mid +/- 15dB.
-
Middle – A rotary control to adjust the amount of Middle +/- 15dB.
-
Hi-Mid – A rotary control to adjust the amount of Hi-Mid +/- 15dB.
-
Treble – A rotary control to adjust the amount of Treble +/- 15dB.
-
Volume – A rotary control to adjust the overall output of the amp.
-
FX Loop – a TSR Jack is provided for use with a Y cable (tip send ring return).
-
Di – A balanced XLR Di Output.
-
Headphones – 1/4” Headphone Jack Output (this actively mutes the speaker for silent practice).
-
F/S – Footswitch out for use with an FS1single latching footswitch (sold separately) to control the Drive-in/out.
-
Line In – For use with a line-level instrument or audio device such as an MP3 player
-
Passive/Active – A -15dB input pad for use with active instruments
-
Input – a 1/4” Jack Socket for use with your instrument
-
Power Switch – Turn your amp on or off
ASHDOWN ENGINEERING – STUDIO 15
-
IEC Power input – a fused IEC power inlet for use with the supplied cable
-
Tweeter Mute – a simple on/off switch to engage/defeat the onboard HF tweeter
ASHDOWN ENGINEERING – STUDIO 210
FEATURES
-
On-light indicates the amplifier is powered.
-
Shape – A switchable pre-shape EQ.
-
Pre-Gain – A rotary control to set the input sensitivity of the amp in conjunction with your instrument.
-
Drive – A rotary control to adjust the amount of tube emulated overdrive.
-
Bass – A rotary control to adjust the amount of Bass +/- 15dB.
-
Lo-Mid – A rotary control to adjust the amount of Lo-Mid +/- 15dB.
-
Middle – A rotary control to adjust the amount of Middle +/- 15dB.
-
Hi-Mid – A rotary control to adjust the amount of Hi-Mid +/- 15dB.
-
Treble – A rotary control to adjust the amount of Treble +/- 15dB.
-
Volume – A rotary control to adjust the overall output of the amp.
-
FX Loop – a TSR Jack is provided for use with a Y cable (tip send ring return).
-
Di – A balanced XLR Di Output.
-
Headphones – 1/4” Headphone Jack Output (this actively mutes the speaker for silent practice).
-
F/S – Footswitch out for use with an FS1single latching footswitch (sold separately) to control the Drive-in/out.
-
Line In – For use with a line-level instrument or audio device such as an MP3 player
-
Passive/Active – A -15dB input pad for use with active instruments
-
Input – a 1/4” Jack Socket for use with your instrument
-
Power Switch – Turn your amp on or off
-
IEC Power input – a fused IEC power inlet for use with the supplied cable
-
Tweeter Mute – a simple on/off switch to engage/defeat the onboard HF tweeter
-
Speaker Mute – a simple on/off switch to mute the onboard speaker for silent use
-
Speaker Output – An 8 Ohm speaker 1/4 output for use with an extension speaker
SPECIFICATION:
Studio Jnr
Output Power
Speaker Unit
Input Impedance
Input Signal Range
E.Q.
Weight| 15watts rms into 8 ohms
1 x 6” Ashdown Driver
1 Meg ohm
100Mv to 10v
Passive Bass, Middle, Treble.
6Kgs 13.1Lbs
---|---
Studio 8
Output Power
Speaker Unit
Input Impedance
Input Signal Range
E.Q.
Dimensions (mm)
Weight| 30watts RMS into 8 ohms
1 x 8” Ashdown Driver
1 Megohm
100Mv to 10v
Passive Bass, Middle, Treble.
H:336 W:360 D:227
6.1Kgs 13.4Lbs
Studio 10
Output Power
Speaker Unit
Input Impedance
Input Signal Range
E.Q.
Dimensions (mm)
Weight| 60watts RMS into 8 ohms
1 x 10” Ashdown Driver
1 Meg ohm
100Mv to 10v
Passive Bass, Middle, Treble.
H:366 W:360 D:302
7Kgs 15.4Lbs
Studio 12
Output Power
Speaker Unit
Input Impedance
Input Signal Range
E.Q.
Dimensions (mm)
Weight| 100watts RMS into 8 ohms
1 x 12” Ashdown Driver
1 Meg ohm
100Mv to 10v
Bass, Hi-Mid, Middle, Lo-Mid, Treble
H:472 W:414 D:357
10.3Kgs 22.7Lbs
Studio 15
Output Power
Speaker Unit
Input Impedance
Input Signal Range
E.Q.
Dimensions (mm)
Weight| 300watts RMS into 8 ohms
1 x 15” Ashdown Driver & Tweeter
1 Megohm
100Mv to 10v
Bass, Hi-Mid, Middle, Lo-Mid, Treble
H:526 W:428 D:378
11.2Kgs 24.6Lbs
Studio 210
Output Power
Speaker Unit
Input Impedance
Input Signal Range
E.Q.
Dimensions (mm)
Weight
-
- 20mm for feet| 300watts RMS into 8 ohms
2 x 10” Ashdown NEO Driver & Tweeter
1 Meg ohm
100Mv to 10v
Bass, Hi-Mid, Middle, Lo-Mid, Treble
H:526* W:428 D:378
11.2Kgs 24.6Lbs
- 20mm for feet| 300watts RMS into 8 ohms
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>