NANFANG CR-E-WIN1 Wall Smart Light Switch Infrare IR Sensor EU Plug Instruction Manual
- June 7, 2024
- NANFANG
Table of Contents
INFRARED SENSOR SWITCH
INSTRUCTION MANUAL
CR-E-WIN1 Wall Smart Light Switch Infrare IR Sensor EU Plug
This infrared sensor switch is applied to replace traditional or old switch panels.It can be directly installed at the place where the original switch lay.You can control the light without touch the switch.When your hand close to the switch in the range of 15cm,the light can turn on immediately.
Notes:
- when wiring lines,please make sure the connections of L and N are completely right.
- After installation,the protective film can betaken off.
Installation:
- Disassemble the original switch from the wall.
- For the infrared sensor switch,you need to takeoff the control part from the switch panel by a small tool.
- Loose the four screws and wire the switch with the live line and naught line.
- Tighten the screws and fix the switch on the wall with screws in the package.
- Cover the panel on the switch.
Specification:
| Type | 86 type(square) |
|---|---|
| Voltage | AC100-240V50/60Hz |
| Power Consumption | <0.05w |
| Rated Power | 800w |
| Relay Output | 10A |
| Connection | L and N lines |
| Infrared sensing distance | ≤15cm |
| Material | PC+Tempered Glass |
| Mount Hole Distance | 60mm |
| Indicator Light | Red for ON,Blue for OFF |
| Screw diameter | 4mm |
| Installation Depth | 26mm |
| Service Life | >20,000 times |
| Dimension | 86x86x35mm |
| Weight | 116g |
| Wireless Type | WiFi 2.4GHz |
How to connect the switch toWi-Fi network
- Download SmartLife App
Scan the QR code to download “SmartLife”App,or search SmartLife in IOS app store or Google play. sign up for an account. https://smartapp.tuya.com/smartlife
IOS&Android System****
Download on the
APP Store| Get it on
Google Play
---|---
2. Connect with mobile phone
when the switch is powered on for the first time,it will automatically enter
the distribution network state.
After the power is turned on,the blue indicator flashes quickly, “Smart
Life”App tap”+”icon on the top right corner.Follow the prompts to add
devices.Once connected,the App will prompt the connection,then click “Done”.
If the blue indicator light does not flash quickly after power on,you can wave
your hand at the position of the switch sensor 10 times continuously, that is,
the switch switches state 10 times continuously, the switch will enter the
network configuration state. (If you have added the switch to the App,this
action wili remove the device from the App.)
Warm Tips
“Please check whether the device is connected with power and your phone is
connected with Wi-Fi.
Check routers:If the router is dual-band router, please select a 2.4GHz network to add device.
Check whether connected devices have reached the Maximum number router connection.If so,please try
*Make sure router wireless MAC filtering function is to turn off the Wi-Fi connection of some devices. enabled.
FCC Caution：
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>