beurer LV 50 Fresh Breeze Instruction Manual

beurer LV 50 Fresh Breeze

| Read these instructions for use carefully and keep them for later use, be sure to make them accessible to other users and observe the information they contain.
---|---
Warning

• The device is only intended for domestic/private use, not for commercial use.
• This device may be used by children over the age of 8 and by people with reduced physical, sensory or mental skills or a lack of experience or knowledge, provided that they are supervised or have been instructed on how to use the device safely, and are fully aware of the consequent risks of use.
• Children must not play with the device.
• Children must not perform cleaning or user maintenance without supervision.
• Disconnect the device from the mains supply during cleaning.
• Clean the device using only the methods specified.
• Do not use any solvent-based cleaning products.
• If the mains connection cable of this device is damaged, it must be disposed of. If it cannot be removed, the device must be disposed of.

Dear customer,
Thank you for choosing a product from our range. Our name is synonymous with high-quality, thoroughly tested products for applications in the areas of heat, weight, blood pressure, body temperature, pulse, gentle therapy, massage, beauty, baby and air.
With kind regards,
Your Beurer team

Getting to know your device

The beurer LV 50 table fan circulates the ambient air. The table fan ensures a cool and pleasant breeze, especially on hot days. Thanks to the three speed settings, you can adjust the table fan to your personal needs. Humidification of the ambient air works according to the evaporation principle.

How does the evaporation principle work?
The table fan draws in the dry warm air from the room, which then comes into contact with the evaporation filter, which is saturated with water. The contact between the air flow and the damp filter surface causes the water to evaporate. The ambient air absorbs the humidity, and the thermal energy required for the evaporation process is extracted from the ambient air. There is a noticeable drop in the temperature of the ambient air.

Included in delivery

Check that the exterior of the cardboard delivery packaging is intact and make sure that all contents are present. Before use, ensure that there is no visible damage to the device or accessories and that all packaging material has been removed. If you have any doubts, do not use the device and contact your retailer or the specified Customer Services address.

• 1x table fan
• 1x micro USB cable
• 1x bottle adapter
• 1x evaporation filter
• 1x PET bottle as a water tank
• 1x set of instructions for use

Signs and symbols

The following symbols are used on the device, in these instructions for use, on the packaging and on the type plate for the device:

| Warning
Warning notice indicating a risk of injury or damage to health| | Manufacturer
---|---|---|---
| Important
Safety note indicating possible damage to the device/accessory| | CE labelling
This product satisfies the requirements of the applicable European and national directives.
| Product information
Note on important information| | Dispose of packaging in an environmentally friendly manner
| Read the instructions| | The products demonstrably meet the requirements of the Technical Regulations of the EAEU
| Disposal in accordance with the Waste Electrical and Electronic Equipment EC Directive – WEEE| | Only use indoors

Intended use

This table fan is intended exclusively for cooling the air indoors. The table fan is intended for private use only. Do not use the table fan if solvents, chemicals, toxic gases or fine dust are present in the ambient air.
The table fan must only be used for the purpose for which it was designed and in the manner specified in the instructions for use. Any improper use may be dangerous. Any other use not recommended by the manufacturer may result in fire, electric shock or personal injury. The manufacturer is not liable for damage resulting from improper or careless use.

Warnings and safety notes

Read the notes carefully. Non-observance of the following information may result in personal injury or material damage.
Warning Keep packaging material away from children. There is a risk of suffocation. To avoid the risk of entanglement and strangulation, store cables and air lines out of the reach of small children.

Electric shock

Warning
As with every electrical device, use this table fan carefully and cautiously, in order to avoid hazards due to electric shock.

• Do not use the device if there is visible damage to the device or accessories (e.g. if the cable or mains adapter are damaged, if the motor fan does not rotate, if the device has malfunctioned, or if it has been dropped or damaged in any way. In this case, contact Customer Services).
• Operate the device only with the mains voltage specified on the device (the type plate is located on the rear of the device).
• Do not operate the device during a storm.
• In the event of defects or operational faults, switch the device off immediately and disconnect it from the mains socket.
• Do not pull on the micro USB cable or device to disconnect the device from the power supply.
• Never hold or carry the device by the micro USB cable. Keep the micro USB cable away from hot surfaces.
• Always switch off the device before disconnecting it from the power supply.
• Never disconnect the mains adapter with wet or damp hands.
• To avoid the risk of fire or electric shock, plug the device directly into a USB port or a suitable USB mains adapter.
• In order to protect persons against electrical hazards, DO NOT immerse the device in water or other fluids.
• Children cannot assess the dangers associated with the use of electrical devices. Therefore, always supervise children when they are near the device.
• Always disconnect the device from the power supply before moving the device, and before changing or cleaning the water tank or evaporation filter.
• Always disconnect the device from the power supply if you do not intend to use the device for an extended period of time.
• Do not place any objects in device openings or in rotating parts. Ensure that the moving parts can move freely at all times. Never drop objects into the openings of the device.
• Do not operate the device outside.
• Never block the air vents or grilles/outlets and do not place the device on a soft surface such as a bed or sofa, as this could cause the device to tip over and block the air inlet or outlet.
• Do not place ANY objects on the device.
• DO NOT run the micro USB cable under the carpet.
• DO NOT cover the micro USB cable with carpets, runners or anything similar.
• DO NOT run the micro USB cable under furniture or devices.
• DO NOT run the micro USB cable in high-traffic areas.
• Arrange the micro USB cable such that it does not pose a trip hazard.
• DO NOT attempt to repair or adjust any electrical or mechanical functions on this device. Failure to do so voids your warranty. There are no parts inside the device that can be serviced by the user (apart from replacing the evaporation filter). Any maintenance work must be carried out by qualified personnel only.
• Ensure that the openings of the device and the micro USB cable do not come into contact with water, steam or other liquids.
• Never reach for a device that is submerged in water. Immediately unplug the mains adapter or micro USB cable from the wall socket/ computer.
• Use only clean water. If the water is very hard, use distilled water.
• Never carry the device when the PET bottle attached and full of water.
• Never place the device upside down.
• Place the device on a firm, level surface. Ensure that there is a distance of at least 15 cm between the device and the wall.
• Keep the device away from heat sources, such as ovens and radiators.
• If you notice an unusual smell when using the device in the intended manner, switch off the device and disconnect it from the power supply. Contact Customer Services at www.beurer.com.
• Do not use aroma oils for application.
• Do not point the air outlet towards an electrical device, book or wooden object.
• The device should ideally be carried by the carrying handle. The carrying handle cannot be exchanged. Never carry the device by the PET bottle or when there is water in the water basin.
• Do not use the device in the bathroom or other damp, enclosed rooms.
• Protect the device from impacts.

Risk of fire

Warning
There may be a risk of fire if the device is used improperly or these instructions for use are ignored.

• Never operate the device underneath a cover, such as a blanket, pillow, etc.
• Never operate the device near petrol or other highly flammable substances.
• To reduce the risk of fire, do not place the micro USB cable near heating registers, heating pads, ovens or heating units.
• Do not operate the device in close proximity to flammable or explosive gas mixtures.
• Keep the device away from sources of heat, as the housing could melt and trigger a fire.

Repairs

Warning

• Only specialist personnel may perform repairs on electrical devices.
  Improper repairs may subject users to considerable danger. For repairs, please contact Customer Services or an authorised retailer.

• Do not open the fan unit.

Handling

Important

• After each use and before each cleaning operation, switch off the device and pull the mains adapter/micro USB cable out of the wall socket.
• Do not place any objects on the device.
• Do not expose the device to high temperatures.
• Protect the device against sunlight and impacts and do not drop it.
• Never shake the device.
• Place the device on a firm, level and dry surface.
• Do not use the PET bottle supplied as a drinking bottle.

Device description

1. Carrying handle
2. Control panel
3. Housing
4. Ventilation grille
5. Filter cartridge with evaporation filter
6. Housing release (front)
7. Water basin
8. Bottle holder
9. Bottle adapter
10. PET bottle
11. Fan
12. Housing release (rear)
13. Micro USB port
14. Micro USB cable

Display and buttons

1. ON/OFF button
   To switch the device on/off

2. FAN button
   For setting the speed of the fan

3. FAN indicator
   1 = low speed
   2 = medium speed
   3 = high speed

4. FILTER indicator
   If the FILTER indicator is illuminated, it means you must replace the evaporation filter

5. ON/OFF indicator
   If the ON/OFF indicator is illuminated, it means the table fan is switched on

Usage

Removing the table fan

1. Open the cardboard packaging.
2. Remove the table fan from the cardboard packaging.
3. Remove all plastic films.
4. Check the table fan and cable for damage. If you notice damage, contact Customer Services at www.beurer.com.

Setting up the table fan

Important

1. Place the table fan on a firm and level surface to prevent vibrations and noise.
2. For an optimum cooling effect, place the table fan in your immediate surroundings. Make sure that there is a clearance of at least 15 cm on all sides around the table fan. Make sure that the air inlet and air outlet are never blocked.

Warning

To avoid the overflow of liquid, never move the table fan during operation or when there is water in the water basin.

Operating the table fan

1. Pull the bottle holder out of the side of the table fan.

2. Fill the supplied PET bottle with cold drinking water. The colder the drinking water, the better the cooling effect. Make sure that the drinking water is clean, not carbonated, and no warmer than 40°C. If the drinking water is very hard, use distilled water. Do not use any other liquids. Use a plastic bottle no larger than 0.5 litres, or fill a bottle with a maximum of 0.5 litres. Otherwise, the increased water pressure could cause the table fan to overflow. Firmly press the bottle adapter included in delivery onto the PET bottle from above. Make sure that the bottle adapter is pressed into the bottle as far as possible, so that no water can leak out. For optimal cooling performance, the filled PET bottle can also be stored in the fridge before use.
   Change the drinking water in the PET bottle daily so that fresh water is always fed into the ambient air.
   

3. Place the PET bottle onto the bottle holder of the table fan as shown. After installing the PET bottle, wait approx. 3-4 minutes before turning on the table fan, so that the evaporation filter can absorb enough water.
   Even when the water tank is empty, the evaporation filter remains damp for some time and continues to cool. The table fan can also be operated without the PET bottle and water supply. In this instance, the table fan functions like a fan without the evaporation principle.
   

4. Connect the micro USB cable provided to a USB mains adapter (output: max. 5 V DC / 0.5 A, not included in delivery).
   

5. Insert the micro USB cable into the micro USB port on the rear of the table fan. Then plug the USB mains adapter (USB mains adapter not included in delivery) into a suitable wall socket. Arrange the micro USB cable such that it does not pose a trip hazard.
   Alternatively, you can also operate the table fan using your computer. To do this, connect the table fan to the computer via the USB port. Make sure that the output values of the USB socket comply with information on the rating plate.
   

6. Press the ON/OFF button to switch on the table fan. A blue indicator light below “ON/OFF” will light up.
   

7. The table fan has three speeds.
   Use the FAN button to select your desired speed.
   1 = low speed
   2 = medium speed
   3 = high speed
   

8. Press the ON/OFF button to switch the table fan off again. The blue indicator light below “ON/OFF” will disappear. If you do not intend to use the table fan for an extended period of time, unplug the mains adapter from the wall socket/unplug the micro USB cable from the computer.

9. After each use, remove the residual water from the water basin, so that no water can escape in the event of accidental impacts. To remove the residual water from the water basin, proceed as follows:

Replacing the evaporation filter

The evaporation filter should be replaced with a new one after 1000 operating hours. After 1000 operating hours have elapsed, the FILTER indicator will light up on the display. To replace the evaporation filter, proceed as follows:

1. Ensure that the table fan is switched off. Disconnect the table fan from the wall socket or computer. Pull the PET bottle and bottle adapter straight up and off.

2. Press the front and rear housing release latches to release the housing. Then carefully pull the housing upwards to remove it, as there may still be residual water in the water basin.
   

3. Pull the filter cartridge up and off.
   

4. Place the new filter cartridge into the water basin from above.
   

5. Place the housing onto the water basin from above until you hear and feel it click into place.
   

6. To turn off the FILTER indicator after replacing the filter, press and hold the ON/OFF button and the FAN button simultaneously for 10 seconds. If you want to replace the filter before the 1000 operating hours expire, proceed as follows: press and hold the ON/OFF button and the FAN button simultaneously for 10 seconds, even if the red filter indicator is not illuminated. The filter indicator will flash red for 3 seconds. Once the flashing has stopped, it means the counter has reset.
   

Cleaning and maintenance

Warning
Ensure that the table fan is switched off before any cleaning operation!

Replacing the evaporation filter

Important
The evaporation filter should be replaced after 1000 operating hours (see “Replacing the evaporation filter” chapter). If the evaporation filter becomes very dirty before the 1000 operating hours have elapsed, replace it beforehand. The evaporation filter cannot be washed. To ensure optimum cooling performance, replace the evaporation filter every 6 months.

Cleaning the housing

Clean the housing and water basin once a week with a slightly damp cloth (water or mild cleaning solution). Do not use solvents, other aggressive cleaning/scrubbing agents or alcohol, as these could damage the surface. Do not use any abrasive or hard objects for cleaning.

Cleaning the PET bottle / bottle adapter / water basin

Important
Never clean any of the removable parts (such as the PET bottle, bottle adapter and water basin) in the dishwasher or using aggressive cleaning solutions.
Only ever clean the removable parts (such as the PET bottle, bottle adapter and water basin) using a mild detergent. In case of heavy lime deposits the water basin can be cleaned with a vinegar solution (household vinegar with water, ratio 1:1). Allow the solution to work in for 10 minutes. Then empty the water basin and rinse it thoroughly with water.

Storage

If you do not plan to use the device for an extended period of time, we recommend that you clean it and store it in the original packaging in a dry environment, ensuring it is not weighed down by other items.

Replacing the PET bottle

Replace the PET bottle as soon as white limescale or other types of dirt start to build up inside.

Important
Do not clean the PET bottle in the dishwasher. The PET bottle is not dishwasher-safe.

Accessories and replacement parts

To purchase accessories and replacement parts, please visit www.beurer.com or contact the corresponding service address (according to the service address list) in your country. Accessories and replacement parts are also available from retailers.

What if there are problems?

the table fan to a suitable wall socket or computer.
The table fan is faulty.| Please contact Customer Services at: www.beurer.com
Insufficient passage of air.| The evaporation filter is dirty.| Clean or replace the evaporation filter (see “Cleaning and maintenance” chapter).
The ventilation grille blocks the air flow.| Open the ventilation grille to allow air to flow through.
Table fan smells unpleasant.| The ventilation fan is new.| Unplug the table fan. Then empty the water basin and allow it to air for 12 hours.
The water in the PET bottle is stale.| Replace the water in the PET bottle.
The evaporation filter has been damp for too long.| Allow table fan to run without PET bottle, so that the table fan can dry out the evaporation filter.
Remove the evaporation filter (see “Replacing the evaporation filter” chapter) and allow it to air dry.

The table fan is very loud.

| The table fan is standing on an unstable and uneven surface.| Place the table fan on a stable and level surface.

Disposal

For environmental reasons, do not dispose of the device with your household waste at the end of its service life. Dispose of the device at a suitable local collection or recycling point in your country. Dispose of the device in accordance with EC Directive ­ WEEE (Waste Electrical and Electronic Equipment). If you have any questions, please contact the local authorities responsible for waste disposal.

Technical specifications

Micro USB cable: approx. 34 g
Permissible operating conditions| -9°~50°C, 20~95% RH
Operating time| approx. 4 hours at level 3 at a relative humidity of 60% (at 22°C)
Volume| low speed = approx. 40 dB medium speed = approx. 45 dB high speed = approx. 50 dB

Warranty/service

Beurer GmbH, Söflinger Straße 218, 89077 Ulm, Germany (hereinafter referred to as “Beurer”) provides a warranty for this product, subject to the requirements below and to the extent described as follows.

The warranty conditions below shall not affect the seller’s statutory warranty obligations which ensue from the sales agreement with the buyer.
The warranty shall apply without prejudice to any mandatory statutory provisions on liability.

Beurer guarantees the perfect functionality and completeness of this product.

The worldwide warranty period is 3 years, commencing from the purchase of the new, unused product from the seller.

The warranty only applies to products purchased by the buyer as a consumer and used exclusively for personal purposes in the context of domestic use. German law shall apply.

During the warranty period, should this product prove to be incomplete or defective in functionality in accordance with the following provisions, Beurer shall carry out a repair or a replacement delivery free of charge, in accordance with these warranty conditions.

If the buyer wishes to make a warranty claim, they should approach their local retailer in the first instance: see the attached “International Service” list of service addresses.

The buyer will then receive further information about the processing of the warranty claim, e.g. where they can send the product and what documentation is required.

A warranty claim shall only be considered if the buyer can provide Beurer, or an authorised Beurer partner, with ­
– a copy of the invoice/purchase receipt, and
– the original product.
The following are explicitly excluded from this warranty:
– deterioration due to normal use or consumption of the product;
– accessories supplied with this product which are worn out or used up through proper use (e.g. batteries, rechargeable batteries, cuffs, seals, electrodes, light sources, attachments and nebuliser accessories);
– products that are used, cleaned, stored or maintained improperly and/or contrary to the provisions of the instructions for use, as well as products that have been opened, repaired or modified by the buyer or by a service centre not authorised by Beurer;
– damage that arises during transport between manufacturer and customer, or between service centre and customer;
– products purchased as seconds or as used goods;
– consequential damage arising from a fault in this product (however, in this case, claims may exist arising from product liability or other compulsory statutory liability provisions).

Repairs or an exchange in full do not extend the warranty period under any circumstances.

BEURER GmbH
• Söflinger Str. 218
• 89077 Ulm (Germany)
•www.beurer.com
www.beurer-gesundheitsratgeber.com
•www.beurer-healthguide.com

References

• Beurer — Beurer North America
• Beurer Gesundheitsratgeber
• Beurer Health Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>