Raspberry Pi Compute Module 4 Antenna Kit User Manual

June 6, 2024
Raspberry Pi

Compute Module 4 Antenna Kit

Raspberry Pi Compute Module 4 Antenna Kit

User Manual

Overview

User Manual

This Antenna Kit is certified for use with the Raspberry Pi Compute Module 4.
If a different antenna is used, then separate certification will be required, and this must be arranged by the end-product design engineer.

Specification: Antenna

  • Model number: YH2400-5800-SMA-108
  • Frequency range: 2400-2500/5100-5800 MHz
  • Bandwidth: 100–700MHz
  • VSWR: ≤ 2.0
  • Gain: 2 dBi
  • Impedance: 50 ohm
  • Polarisation: Vertical
  • Radiation: Omnidirectional
  • Maximum power: 10W
  • Connector: SMA (female)

Specification – SMA to MHF1 cable

  • Model number: HD0052-09-A01_A0897-1101
  • Frequency range: 0–6GHz
  • Impedance: 50 ohm
  • VSWR: ≤ 1.4
  • Maximum power: 10W
  • Connector (to antenna): SMA (male)
  • Connector (to CM4): MHF1
  • Dimensions: 205 mm × 1.37 mm (cable diameter)
  • Shell material: ABS
  • Operating temperature: -45 to +80°C
  • Compliance: For a full list of local and regional product approvals,
    please visit
    www.raspberrypi.org/documentation/hardware/raspberrypi/conformity.md

Physical dimensions

Physical dimensions

Fitting instructions

  1. Connect the MHF1 connector on the cable to the MHF connector on the Compute Module 4
  2. Screw the toothed washer onto the SMA (male) connector on the cable, then insert this SMA connector through a hole (e.g. 6.4 mm) in the end-product mounting panel
  3. Screw the SMA connector into place with the retaining hexagonal nut and washer
  4. Screw the SMA (female) connector on the antenna onto the SMA (male) connector which now protrudes through the mounting panel
  5. Adjust the antenna to its final position by turning it through up to 90°, as shown in the illustration below

Fitting instructions

WARNINGS

  • This product shall only be connected to a Raspberry Pi Compute Module 4.
  • All peripherals used with this product should comply with relevant standards for the country of use and be marked accordingly to ensure that safety and performance requirements are met. These articles include but are not limited to keyboards, monitors and mice when used in conjunction with the Raspberry Pi

SAFETY INSTRUCTIONS

To avoid malfunction or damage to this product, please observe the following:

  • Do not expose to water or moisture, or place on a conductive surface whilst in operation.
  • Do not expose it to external heat from any source. The Raspberry Pi Compute Module 4 Antenna Kit is designed for reliable operation at normal ambient room temperatures.
  • Take care whilst handling to avoid mechanical or electrical damage to the Compute Module 4, Antenna, and connectors.
  • Avoid handling the unit whilst it is powered.

SAFETY INSTRUCTIONS To avoid malfunction or damage to this product, please
observe the following: • Do not expose to water or moisture, or place on a
conductive surface whilst in operation. • Do not expose it to external heat
from any source. The Raspberry Pi Compute Module 4 Antenna Kit is designed for
reliable operation at normal ambient room temperatures. • Take care whilst
handling to avoid mechanical or electrical damage to the Compute Module 4,
Antenna, and connectors. • Avoid handling the unit whilst it is
powered.

Raspberry Pi and the Raspberry Pi logo are trademarks of the Raspberry Pi Foundation
www.raspberrypi.org

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals