TOPGREENER TGWF500D Wireless Home Automation WiFi Dimmer Instruction Manual

TOPGREENER TGWF500D Wireless Home Automation WiFi Dimmer

FEATURES

• Control your lights with your smart devices without the need of any hubs.
• Easily configure use through Smart App.
• Save energy by automating the ON/OFF times.
• Compatible with Amazon Alexa, Google Assistant, IFTTT.

SPECIFICATIONS

• Incandescent …………………………………………………600W, 120V~60Hz
• CFL/LED/Self Ballasted ……………………………………………….2A, 150W
• Protocol ………………………………………………………… IEEE 802.11b/g/n
• Wireless Type ……………………………………………………………… 2.4GHz
• Operating Temperature ………………………………. 32º – 104ºF (0º-40ºC)

NOTE:
This device is not compatible with standard 3-way or 4-way switches. 3-Way and 4-way capabilities require the TGWF3K auxiliary switch.

REQUIREMENTS

• Wi-Fi Internet connection of 2.4GHz.
• Smart Device such as a Smart Phone or Tablet with an operating system of Android ver. 4.1 or higher or iOS 8 of higher.
• Installation of the TOPGREENER Smart App on the Smart Device.

WARNING

Turn the POWER OFF at the circuit breaker before installing the Dimmer. Read and understand these instructions before installing. This device is intended for installation in accordance with the National Electric Code and local regulations. It is recommended that a qualified electrician performs this installation. Use copper wire only. Use wires with a minimum temperature rating of 75ºC (167ºF)

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 8in (20cm) between the radiator & your body.

RF Exposure
A distance of 8in (20cm) shall be maintained between the antenna and users, and the transmitter module may not co-locate with any other transmitter or antenna.

WIRING DIRECTIONS

First, decide if you will be controlling the lights from one location or multiple locations. Next, identify all wires. Once you’ve identified the wires, follow the diagram below for wiring.

Single Pole Installation For 3-Way or 4-Way wiring, follow the instructions on the TGWF3K auxiliary switch

OPERATING THE DIMMER

After the TGWF3K Add-On Switch has been properly connected to the TGWF500D Dimmer, the Add-On Switch will operate the same way the TGWF500D does.

• To turn on the lights ON to the last used brightness level, press and release the top Dimmer Paddle
• To brighten the lights, press and hold the top Dimmer Paddle and release when the desired level is reached
• To dim the lights, press and hold the bottom Dimmer Paddle and release when the desired level is reached
• To save the brightness level and turn off the lights, press and release the bottom Dimmer Paddle

CHANGING THE FACE COVER

To replace the face cover, use a flat screwdriver and insert the tip at the gap shown in the diagram above and pry cover off. To re-install, simply align the cover and snap back on.

INITIAL SET UP FOR Wi-Fi CONTROL

1. Connect the TGWF500D, then turn on the circuit breaker.
2. Connect your Smart Device (phone or tablet) to the same 2.4GHz Wi-Fi network that your TGWF500D dimmer will be connecting to.
3. Use your mobile device and search “TOPGREENER” from the App Store or Google Play, then download and install it.
4. Open the App and FOLLOW THE ON-SCREEN INSTRUCTIONS to register, log in and connect the Smart Plug to your network. Over time, the App may be updated for a better experience or added features, so be sure to follow the in-App instructions closely:
   • Login to the App
   • Navigate to the Devices tab and click “Add Device” or the “+” button
   • Select the device type  “In-Wall Dimmer”.
   • When prompted to “power on the device and confirm”, push the up or down button on the TGWF500D five times, then hold that same button on the sixth press and the LED indicator on the device will start blinking rapidly. When LED starts blinking, press “Confirm indicator rapidly blinks”.
   • Enter your Wi-Fi password when prompted and click on confirm.
   • After successfully adding the device, you can change the name of the device if desired.

Configure Device in AP mode

AP mode is a secondary way to configure your device to work on your network. Configuration in this mode requires a connection from your smart device to the smart switch. To do so, go to the “Add Device” screen and click on “AP Mode” at the top of the screen and follow the on-screen instructions.

NOTE:
By default, the app will only allow one user to control the Switch. To add users, go to your “profile” on the app and click on “Device Sharing” and follow the on-screen instructions.

SAFETY NOTICE

Please note: pressing and holding the dimmer switch paddle until the light intensity is at the minimum setting does not turn the power OFF, you must still tap (short press) the bottom of the dimmer switch paddle to turn the power OFF.

The Air Gap Switch located below the Dimmer Switch Paddle is designed for your safety. With push button switches, it is difficult to know if the switch is in the On or the Off position without having to use a tester. This switch eliminates the hazard of having to change a light bulb on a possibly live fixture. Use the Air Gap Switch to Power Off before you change the bulb.

THE LED INDICATOR ON THE DEVICE

• Solid Green: The device is plugged into a power source, but it has not been paired or the device has connection problems.
• Slow Blinking Green: The device is attempting to pair with the controller while in APN mode. When LED turns off, the device has been paired successfully.
• Fast Blink ing Green: The device is attempting to pair with the controller while in Easy mode. When LED turns off, the device has been paired successfully.
• Solid Blue: Device is paired and the power is turned ON.
• No Light: The device is paired and the power is turned OFF.

Works seamlessly with Tuya IoT apps and chipsets. Use any Tuya app with any Top Greener device and use any Tuya device with Top Greener’s app.

WARRANTY

This device is warranted to be free of material and workmanship defects for 1 year from the date of purchase. An original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL claims must be verified and approved by Top Greener, Inc. Warranties from other TOPGREENER products may vary. This warranty is non-transferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation. To the fullest extent permitted by the applicable state law, Top Greener, Inc. shall not be liable to the purchaser or end-user customer of TOPGREENER products for direct, indirect, incidental, or consequential damages even if Top Greener, Inc. has been advised of the possibility of such damages. Top Greener, Inc’s total liability under this or any other warranty, express or implied, is limited to repair, replacement or refund. Repair, replacement or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.

• 2018 Top Greener, Inc.
• CA, USA
• www.topgreener.com
• 0206180114-04

References

• Wiring Devices, Lighting Controls, Smart Home | TOPGREENER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>