Bresee DR21-8UW 8-Inch Face Recognition Access Control Equipment Instructions
- June 6, 2024
- Bresee
Table of Contents
Bresee DR21-8UW 8-Inch Face Recognition Access Control Equipment
Statement
Without the written permission of the company, no unit or individual shall extract or copy part or all of the contents of this manual without authorization, and shall not disseminate it in any form. Due to product version upgrade or other reasons, the contents of this manual will be updated from time to time. This manual is only used as a guide, and all statements, information and suggestions in this manual do not constitute any express or implied warranty. The company shall not be liable for any special, incidental, accidental or indirect damage caused by the use of this manual or the use of the company’s products, including but not limited to the loss of business profits, loss of data or documents, abnormal operation of products and information disclosure caused by network attack, hacker attack, virus infection, etc.
Safety instructions
- This is a class a product, which may cause radio interference in the living environment. In this case, users may be required to take practical measures against their interference.
- Please disconnect the power supply before moving the equipment. Be careful to prevent electric shock when moving. Once the power cord is inserted into the power supply, the equipment will be powered on.
- Please ensure that the equipment is installed stably and reliably, the surrounding ventilation is good, and the ventilation outlet must be unblocked when the equipment is working.
- Please ensure that the equipment works within the allowable temperature, humidity and power supply requirements, and is well grounded to meet the lightning protection requirements, and avoid being placed in dusty, strong electromagnetic radiation, vibration and other places.
- Please protect the power cord from trampling or squeezing, especially at the plug, power socket and the contact from the device.
- After installation, please check the correctness to avoid human injury and equipment component damage due to wrong connection during power on.
- Abnormal power failure may cause equipment damage or abnormal function. If the equipment is used in the environment of frequent power failure, please provide ups.
- Make the equipment work within the allowable temperature and humidity range, and avoid being placed in places such as extrusion, vibration, extreme heat, extreme cold and strong electromagnetic radiation. To avoid fire and electric shock hazards, do not allow water or other liquids to flow into the equipment during use.
- If the equipment cannot be maintained due to unauthorized operation, the company will not bear all the consequences arising therefrom.
Packing list
If you find any items damaged or missing, please contact your local dealer in time.
| No | item | number | unit |
|---|---|---|---|
| 1 | DR21-8UW | 1 | pcs |
| 2 | Tail line – grid port | 1 | pcs |
| 3 | Tail line – full function | 1 | pcs |
| 4 | The power adapter | 1 | pcs |
| 5 | Accompanying instructions | 1 | pcs |
| 6 | certificate | 1 | pcs |
| 7 | warranty card | 1 | pcs |
| 8 | Wall mount bracket set | 1 | pcs |
| 9 | Wall mount bracket sticker | 1 | pcs |
| 10 | Screw package | 1 | pcs |
Product introduction
product description
T82 is a high-performance and reliable portrait identification access control
product. This product supports a variety of recognition modes such as portrait
white list recognition, portrait and IC card verification. It adopts the idea
of industrial appearance design, with light and thin body, smooth lines, high
recognition rate, large storage capacity, fast recognition and so on. Through
the access management platform, multiple applications such as access control
management, attendance management and visitor management can be realized,
which is suitable for various scenarios such as parks, universities,
enterprises, communities and hospitals.
Product Specification:
Support 802.11b/g/n20/n40(2.4G WIFI): 18.5dBm EIRP(Maximum power) 13.56MHz NFC
product dimensions
Equipment dimension drawing, as shown
structure description
The appearance of equipment structure is shown in Figure 2-2. Please refer to
the real object for details. 
| Serial number | name | explain |
|---|---|---|
| 1 | Led fill light | Fill RGB camera |
| 2 | Infrared fill light | Fill in light for infrared camera |
| 3 | Infrared camera | Take infrared images |
| 4 | RGB camera | Take visible images |
| 5 | Mic outlet | For voice intercom |
| 6 | speaker | Play voice prompt |
| 7 | Tail line output hole | Panel tail line hole |
installation instructions
Please check before installing the product to ensure that the product can work normally. This document provides wall mounted installation methods for reference, and other installation instructions can be obtained by contacting our personnel;
wall mounted installation
- Step 1: as shown in Figure 3-1, fix the sheet metal on the back of the machine body with screws ①;
- Step 2: Mark four positioning points on the wall to confirm the installation position of the wall hanging support;
- Step 3: as shown in Figure 3-1, align the four holes on the wall hanging bracket with the wall positioning point, lock four self tapping screws ②,
- and fix the wall hanging bracket;
- Step 4: as shown in Figure 3-1, fasten the access control terminal sheet metal to the wall hanging support through position ③;
- Step 5: as shown in Figure 3-1, use screws ④ to fix the access control terminal and the wall hanging bracket;
- Step 6: after installation, as shown in Figure 3-2;
wiring instructions
schematic diagram of tail line
interface description
Serial number| Interface name| Interface description| Pin color| Pin
description
---|---|---|---|---
P1| RJ45
network port
| Wired network port communication| /| RJ45
network port
P2| 12V power supply| 12V power input| /| DC_12V
P3| USB2.0| USB2.0 Interface| /| USB
interface
P4| Relay output 1| Output IO signal| WHITE| NO1
ORANGE| COM1
RED| NC1
P5| Relay output 2| Output IO signal| GRAY| NO2
WHITE/ORANG E| COM2
| | | WHITE/RED| NC2
---|---|---|---|---
P6| RS485| RS485
communication
| BLACK| GND
RED| 5V
WHITE/PURPL E| RS485+
BROWN| RS485-
P7| WG_OUT| Wigan signal output| BLACK| GND
YELLOW/GRAY| WG_OUT_D 0
WHITE/YELLO W| WG_OUT_D 1
P8| ALM_IN、SEN_IN| Alarm signal input, door magnetic signal input| BLACK| GND
PINK| ALM_IN1
YELLOW/BLAC K| ALM_IN2
WHITE/GREEN| SEN_IN1
Equipment Use
starting equipment
After correct installation, connect the power adapter to the mains and the other end to the equipment power interface to start the equipment. When the display is powered on, it indicates that the device is started successfully.
portrait entry
-
browser configuration
-
DHCP login (factory default DHCP);
Enter the IP address in the upper left corner of the device display in the browser to enter the web login interface, as shown
-
Static IP login:
Step 1: click the < setting > button on the device display screen interface; Enter the initial password < admin > to enter the network configuration interface.
Step 2: close DHCP and modify the static IP address, subnet mask and default gateway
Save after, power off and restart the equipment.
Step 3: enter the modified IP in the browser to enter the web login interface.
● Default static IP：192.168.0.13；
● Subnet mask：255.255.255.0； -
Log in to the web interface:
After accessing the IP address of the device through the browser, enter the user name and password of the device, and click OK Click < login >, and you can enter the web management interface. Default user name: admin; Default password: admin. -
new personnel
-
Select [personnel management – personnel information] interface and select the personnel library to add personnel
-
In the personnel list operation bar, click < add >;
-
In the pop-up new personnel interface, refer to the following table to configure personnel information;
-
Click < save > to finish adding personnel.
portrait recognition
The tester can realize the portrait recognition function by placing it
directly in front of the portrait recognition equipment.
Note: detailed instructions for the use of portrait recognition terminal can
be obtained by contacting our personnel.
EU DECLARATION OF CONFORMITY
Hereby, Bresee Technology Co.,Ltd. declares that the radio equipment type
DR21-8UW , DE21-8TW is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity Please see attachment DOC
Letter
FCC Caution
§ 15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated withminimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>