ReliaSpeak PVR2 PvR Privacy Voice Protector User Manual
- June 6, 2024
- ReliaSpeak
Table of Contents
PvR Bluetooth Voice Protector User Manual for Voice Message Encryption
ReliaSpeak ReliaSpeak Information Technology Co., Ltd
Tel: 86-010-88334733
Website: www.rtspeak.com
Email: [email protected]
Switch Encryption Modes
PVR supports two encryption modes of encrypted call and encrypted voice
message. When in the encrypted call mode, the user can make an encrypted call
during a normal call While in the encrypted voice message mode, a voice
message will be protected by encryption.
Encryption Modes Indication
When PVR is turned on, the indicator light “SEC will show the encryption mode
while in standby status. “SEC” is off, which means PVR is in the encrypted
call mode. “SEC” is flashing, which means PVR is in the encrypted voice
message mode.
Switch Encryption Modes
After PVR is turned on, quickly press the “Function Button” twice to switch
the encryption modes.
PVR will reset to encrypted call mode when is turned off and turned on again.
Send & Play Encrypted Voice Message
Send Encrypted Voice Message
O Switch PVR to encrypted voice message mode.
O Select audio message icon on the IM App.
O Speak to the PVR’s microphone.
Notice: Before sending encrypted voice messages, please make sure the IM
App supports sound pickup through Bluetooth. Otherwise, the message can’t be
encrypted by PvR.
Play Encrypted Voice Message
Switch the PVR to encrypted voice message mode.
Play the encrypted voice message on the phone, the original voice message can
be heard via PVR after being decrypted.
2021 RollaSpeak Information Technology Co.. Ltd. All rights reserved.
Change the Key of Voice Message
In order to play the encrypted voice message correctly, both the sender and
receiver must use the same key, otherwise, only the noise can be heard by the
receiver. The voice message key can be set by the following web page.
https://www.rlspeak.com/pvrvmk/
Change the Key
- Connect PVR to the phone, and switch to the encrypted voice message mode.
- Increase the volume of PvR to 80%-90% level.
- Visit the key setting page.
- Input any 6 digits, then click the “Submit” button.
- PVR will play a success or failure prompt according to the result of key updating.
Notice:
1. The default key is 123456.
2. Please rest assured that there will be no storage of device or user
information when using this page to replace the key. If any concern about
security, the web page codes are allowed to be checked at any time.
==Important Notice==
- The function of encrypted voice messages is only applicable to Apps that support Bluetooth sound pickup, such as WhatsApp (iOS only), Skype, WeChat, etc.
- Both the sender and receiver must use the same key.
- As there will be a delay during the voice encryption process, before starting to speak, please wait 1–2 seconds after tapping the record button when sending a voice message. Also delay 1-2 seconds to release the record button after ending the speech, so as to ensure the integrity of the encrypted voice message.
- While the PVR is in encrypted voice message mode, a phone call is not supported and power consumption is also higher. Please switch the PVR to encrypted call mode or turn it off directly while not in use.
- The encrypted voice messages stored in the phone are secure, the voice played will be noise unless using PvR with the correct key set.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and car radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver. Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. Consult the dealer or an experienced radio/TV
technician for help. Caution: Any changes or modifications to this device not
explicitly approved by the manufacturer could void your authority to operate
this equipment. This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.