RENPHO R-G002 Finger Eye Massager User Manual
- June 6, 2024
- Renpho
Table of Contents
RENPHO R-G002 Finger Eye Massager
Attention
Please read this instruction manual carefully before using. RENPHO assumes no
responsibility for any consequences caused by misuse or failure to follow
these instructions.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without
supervision.
- DO NOT use if you have had an eye operation, or if you have any eye diseases such as glaucoma, cataract, and amotio retinae.
- Disabled people, and the elderly should only use this product when properly supervised.
- DO NOT use if you have any swelling in the eye area.
- lf you feel any pain around your eyes, please discontinue using the device and consult a physician.
- DO NOT use in high temperatures or humid environments. Avoid direct exposure to the sun.
- Do not use the device with wet hands.
- Remove contact lenses, glasses, false eyelashes, hairpins, and hair accessories, etc before using.
- Only use the charger (5V 1A, not included) to recharge the eye massager.
- DO NOT clean the product with water; clean it with cotton soaked in alcohol.
- .Avoid contact with sharp objects.
- Do not use this product while driving.
- lf any fault or malfunction should occur during use, take it off immediately. Never attempt to disassemble or repair the device yourself.
- The device is for private use only and cannot be used as medical equipment. It is not intended for medical diagnosis, treatment, or commercial purposes.
- Use it in the morning and evening for no more than 10 minutes each time.
- Please keep this manual for future reference.
Product Structure
Power Button
Long press: Power ON/OFF Short press: Switch modes. (Quick press twice to
switch between Silent Mode and Voice Mode.)
Specification
Product Name: Finger Eye Massager
Model: R-G002
Input: 5V = 1A
Rated power: SW
Auto-off Timer: 10 minutes
Battery Capacity: 700mAh
Product Weight: 0.4Ib/188g
Product Size: L7xW3xH2.9(inch)/L181.5xW76xH74mm
What’s included
- 1 x RENPHO Finger Eye Massager
- 1 x USB Cable
- 1 x User Manual
Using the Product
Charging
- Use the 5V mobile charger (not included) to charge your eye massager.
- lnsert USB cable into the socket of the mobile charger.
- Softly insert the USB plug into the socket of the device.
- While charging, the LED indicator will flash red. When done charging, the LED indicator will be solid red.
- The charge duration will be about 2 hours. Disconnect the power adapter after charging is complete.
- The massager and the adapter may become warm during normal charging process.
- Use time may differ depending on the operation mode selected.
- The device can not be turned on while charging.
| Status | Indicator Light |
|---|---|
| Normal Operation | Solid White |
| Bluetooth Connected | Solid Blue |
| Low Battery | Flashing Red slowly |
| Charging | Flashing Red slowly |
| Fully charged | Solid Red |
| Overcharging | Flashing Red quickly for one minute |
Wear this device
- Loosen the adjustable headband.
- Place the device around your head and tighten the headband to the appropriate fit.
- Be careful to ensure the device is not too tight around your head.
- Please make sure that you have removed your contact lenses, glasses, false eyelashes, etc. before using this device.
- Do not operate the device with wet hands.
Bluetooth Connection
- Turn on the device by long press the Power Button.
- Enable your mobile phone Bluetooth setting and search for “R-G002”, an audio voice “Bluetooth Connected”will confirm when the device is connected to Bluetooth.
- After successfully pairing your device, music can be pushed to the device for playing while massaging.
Note: After connecting Bluetooth successfully for the first time, it will be connected automatically next time it’s turned on.
Operation
-
Long press the Power button to turn on the massager and there will be a voice prompt “Welcome to the RENPHO Eye Massager” and it will broadcast the current mode.
This massage has memory function. It will run the mode selected last time. -
Short press the Power Button to switch modes. An audio voice will confirm mode change.
Mode| Mode Name| Intensity
---|---|---
Mode 1| Tension Relief Mode| Low
Mode 2| Retinal Protection Mode| Medium
Mode 3| Youthful Radiance Mode| Medium High
Mode 4| Regeneration Mode| High -
Long press the Power Button to turn off the massager, the indicator light will go off.
Auto-off timer: a voice prompt “Your REN PHO Massage is complete” will be heard when the device has been in operation for 10 minutes. And indicator light will go off and the device will automatically shut down.
Silent Mode & Voice Mode
Quick press the Power button twice to switch between Silent Mode and Voice
Mode.
In the silent mode, there will be a voice prompt “Silent Mode” and all the
voice broadcast and built-in music will stop. Bluetooth music plays normally.
Note: Every time the product is turned on, it will enter Voice Mode.
Warm Tips
- When you are using this device, please keep your eyes closed, lean back in the chair and completely relax your body.
- Your vision will become blurry for a short period of time after use. Regular vision will return faster if eyes are kept closed for a short while.
Attention
| Problem | Possible Cause | Solution |
|---|---|---|
| Power-on failure | 1. Check whether the battery level is too low |
2. The time of pressing Power Button is too short
| 1. Please charge the the device in time
2. Long press the Power Button for 2-3 seconds
Low massage intensity| Battery level is low| Charge the device
Device turns off
automatically
| 1. Battery level is low
2. 10 Minutes Automatic Shut-off
| 1. Charge the device
2. Turn on the massager again
The product can’t be charged| 1. The charging voltage is too high
2. Adapter is broken
| 1. Use 5V 1A charger
2. Change another adapter
The indicator light is too dim or flashes
| Low battery| Please charge the device in time
---|---|---
If you encounter other problems, turn off the device and contact us at
support@renpho.com.
Cleaning and Maintenance
- Please turn off the power when cleaning, do not use corrosive detergents such as benzene or diluents to clean the product.
- Do not expose the device to excessive sun or hot temperatures. When the device has not been used for over 3 months, recharge it before use.
- Do not place it next to a wall or on the ground or rooftop.
- Keep the device dry, clean, and away from rats.
- Do not place anything heavy on it. Always bring your product to a qualified professional for any service or repair.
- Do not disassemble the product yourself.
- Do not disregard the device with normal household waste at the end of its life; instead, follow local environmental regulations and guidance for disposal.
FCC Regulatory Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
ISED Regulatory compliance
This device contains license-exempt transmitters that comply with Innovation,
Science and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Warranty (1-Year-Limited)
- The manufacturer’s warranty is void under the following circumstances but not limited to:
- Improper or inadequate maintenance or modification.
- Accident, misuse, abuse, contamination, or other external causes.
- The use of unspecified adapter and accessories.
- Loss or damage in transit.
- Damages that occurs as a result of one’s failure to follow the instructions.
- This warranty does not apply to expendable or consumable parts and does not extend to any product from which the serial number has been removed.
Customer Service
We have a warranty, exchange, and customer service team that guarantees
hassle-free solutions to any issue you might have.
t. Tel: +1(844) 417 0149 (US)
Monday-Friday 9:00AM-4:30PM
111 Email: support@renpho.com
@ Web: www.renpho.com
JOICOM CORPORATION
14129 The Merge Street, Building 3 Unit A, Eastvale, CA 92880
Shenzhen Runfeng Digital Technology Co.,Ltd. Chuanghui Building, Intersection
of Banxuegang Boulevard and Yongxiang Road, Bantian Subdistrict, Longgang
District, Shenzhen, China
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>