AIAIAI H10 Studio Wireless Headband User Guide
- June 6, 2024
- AIAIAI
Table of Contents
AIAIAI H10 Studio Wireless Headband
overview
Power on/off
1. On the H10, press and hold the middle button for 3 sec
2. On the X01, press and hold the button for 3 sec
2.4GHz low latency mode
Pairing 2.4GHz low latency
1. Make sure the slide switch on H10 is set to 2.4GHz low latency mode
(white)
2. On the H10, when powered on, press and hold the top and bottom button for
3 sec to enter pairing mode (LED blinking fast)
3. On the X01, when powered on, double press the button to enter pairing mode
(LEDs blinking fast)
4. Pairing is succesful when the LED on H10 and X01 are solid white
Bluetooth© mode
Pairing Bluetooth©
1. Make sure the slide switch on H10 is set to Bluetooth© mode (blue)
2. On the H10, when powered on, press and hold the top and bottom button for
3 sec to enter pairing mode (LED blinking fast)
3. Activate pairing mode on your connecting device and look for “AIAIAI TMA-2
(H10)”
4. Pairing is succesful when the LED on H10 is solid blue
General info Warranty
AIAIAI TMA-2 H10 and X01 are covered by a 2 year limited warranty.
For more information, please visit:
aiaiai.audio/help/warranty
Contact
AIAIAI ApS
Studiestræde 31
1455 Copenhagen K.
Denmark
Email: support@aiaiai.audio
Product manual
Scan the QR code for more details.
Regulatory info
FCC Caution
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
IC Warning
CAN ICES-003 (B)/NMB-003(B)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
The device is in compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.
To prevent possible hearing damage, do not listen at high volume levels for
long periods.
Hereby, AIAIAI ApS declares that the radio equipment type H10 and X01 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address: aiaiai.audio
Hereby, AIAIAI ApS declares that the radio equipment type H10 and X01 is in compliance with UK Radio Equipment Regulations (SI 2017/1206). The full text of the UK declaration of conformity is available at the following internet address: aiaiai.audio
Manufacturer information:
Company name: AIAIAI ApS
Address: Studiestræde 31,Copenhagen K, 1455 Denmark
Operation temperature: -20~55°C
Charging temperature: 0-45°C
Operation frequency (Max power for CE and UKCA)
Bluetooth: 2402-2480 MHz (2.58dBm)
SRD: 2403.35-2477.35 MHz (1.41dBm)
H10 – FCC ID: 2AKSOH1001
X01 – FCC ID: 2AKSOX0101
IC: 23880-TMA2H10
IC: 23880-TMA2X01
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>