Shenzhen Xuyuan Technology XYD0001 Smart Light Bulb User Manual
- June 6, 2024
- Shenzhen Xuyuan Technology
Table of Contents
SMART LIGHT BULB
Model: XYDOOOl
http://barcode.vesync.com/?v=new-1-1
To download the VeSync app, scan the QR code or search “VeSync” in the Apple App Store® or Google Play Store.
Open the sync app. If you already have an account, tap login. To create a new account, tap Sign Up.
Screw-in your smart bulb.
Note: This bulb only supports 2.4GHz networks. If you connected the bulb to a 5GHz network before, please switch to the 2.4GHz network.
Tap+ in the VeSync app and VeSync will automatically search for the bulb. If the app cannot discover the bulb, you can also find it by tapping “Lighting” and choosing “Valceno WiFi Bulb”.
Follow the in-app instructions to add your smart bulb.
Thank you for choosing Volcano! This device is intended to be used indoors only.
Reset
- Turn the bulb on and off 7 times, keeping it on for 2 seconds then off for 2 seconds each time. The bulb will start flashing a red color.
- After 5 seconds, the bulb will show a white color, indicating the bulb has been reset to its default settings.
Cleaning and maintenance
Do not use cleaning solvents or abrasives.
Do not clean the inside of the device.
Do not attempt to repair the device. If the device does not operate correctly,
replace it with a new device.
Clean the outside of the device using a soft cloth.
Connect with Amazon Alexa or Google Assistant
Tap More > Third Party Services > Alexa/Google Assistant to connect your bulb
to Amazon Alexa or Google Assistant.
For troubleshooting, tap “?” in the top right corner of the screen.
Note: You must create your own VeSync account to connect with Alexa/Google Assistant.
If you can’t use the voice control correctly, try to remove the device from VeSync APP and then reconfigure it.
Troubleshooting
I cannot connect my bulb to the VeSync app.
- During the setup process, make sure your bulb is connected to a secure 2.4GHz Wi-Fi network.
- Make sure the Wi-Fi password you entered is correct.
- Make sure your bulb is in Configuration Mode. If not, switch the bulb on and off three times in a row (2 seconds on and 2 seconds off), the bulb will start flashing with different colors.
- Move your bulb closer to the router. The distance between the bulb and router should be within 98ft/30m.
- Place your router in a higher position away from such appliances as microwave ovens, refrigerators, electronic devices, etc. to avoid signal interference.
- Tum the bulb on and off 7 times, keeping it on for 2 seconds then off for 2 seconds each time. The bulb will start flashing a red color. After 5 seconds, the bulb will show a
white color, indicating the bulb has been reset to its default settings
Why do I need to tum on my phone’s location or GPS when I’m setting up my
bulb?
GPS or location services should be enabled on your Android™ phones for
Bluetooth scanning, which is required for connecting your bulb to the
internet.
I cannot connect my bulb to Amazon Alexa or Google Assistant.
- Make sure VeSync can control your smart bulb remotely.
- Try to unlink your VeSync account from Amazon Alexa/Google Assistant, then link again.
- Tap More > Third Party Services > Alexa/Google Assistant to connect your bulb to Alexa or Google Assistant. For troubleshooting, tap “?” in the top right corner of the screen.
Lights Flickering
Check if the bulb is connected to the power supply properly.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will
not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications
not expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End-users must follow the specific operating
instructions for satisfying RF exposure compliance. To maintain compliance
with FCC RF exposure compliance requirements, please follow operation
instructions as documented in this manual. This
the transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. The availability of some specific channels
and/or operational frequency bands are country-dependent and are firmware
programmed at the factory to match the intended destination. The firmware
setting is not accessible by the end-user.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
No-replaceable light source.
Not intended for illumination. Only used for creating ambiance.
Amazon, Alexa, and all related logos are trademarks of Amazon.com, Inc. or its affiliates.
Google, Android, and Google Play are trademarks of Google LLC.
Wi-Fi@ is a registered trademark of Wi-Fi Alliance@.