12 SPEED PRODUCTS DOORMATE2 Garage Door Opener User Manual

October 30, 2023
12 SPEED PRODUCTS

DOORMATE2 Garage Door Opener
User Manual

DOORMATE2 Garage Door Opener

For use with the listed garage door openers manufactured (TABLE BELOW). The garage door opener activates when the programmed button on the remote control is pressed. The remote control can activate a garage door opener.
Make sure the garage door opener has a working light bulb because it is a programming indicator.
WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Package Includes

12 SPEED PRODUCTS DOORMATE2 Garage Door Opener - Package
Includes

WARNING
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door.
ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with remote controls. Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.
ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

PREPARE

Locate the LEARN BUTTON on the garage door opener.
NOTE: Your garage door opener may look different.

12 SPEED PRODUCTS DOORMATE2 Garage Door Opener - garage
door

PROGRAMMING THE REMOTE

  1. Using the provided safety pin, press and hold the PROGRAM BUTTON on the remote control until the LED on the front of the remote control turns on. This mode will last one minute.

  2. Press and release the REMOTE BUTTON the number of limes that corresponds with the garage door opener type

  3. To exit programming mode, press PROGRAM BUTTON.

  4. Press and release the LEARN BUTTON on the garage door opener

  5. Press the REMOTE BUTTON programmed in step 2 until the garage door opener lights flash or two clicks are heard.

  6. To test, press the REMOTE BUTTON on the remote control.. Repeat process for button 2 for a different door.

WARNING
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door.
ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with remote controls.
Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.
ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.
Locate the PROGRAM BUTTON on the remote control.
Locate your model of garage door opener in the table below to determine the number of button presses needed to program the remote control.

Number of button presses needed Brand Type/Color of smart/Learn
1 time  Linear Mega Code 1997-current 318 MHz
2 times Chamberlain Lift aster Craftsman Orange+red button 1997-2005 390MHz
3 times Chamberlain Lift aster Craftsman Purple button 1999-2009 315 MHz
4 times Chamberlain Lift master  Craftsman Green button 1993-1996 390 MHz
5 times Genie Overhead Door Intellicode 2005-current 315 MHz
6 times Genie
Overhead Door Intellicode 2005-current 390 MHz
7 times Chamberlain Lift master Craftsman Yellow button 2011-current 310MHz

INSTALLING REMOTE CONTROL ON STEM

  1. Ensure the stem and handlebars are installed, aligned, and torqued according to manufacturer’s recommendations.
  2. Remove the original top cap and mounting bolt.
  3. Install Doormat 2 top cap on top of the stem.
  4. Install, but do not fully tighten, M6 x 30mm bolt.
  5. Install Doormat 2. Set the top cap mount to your desired position.
  6. Remove the Doormat 2 with the locking tool.
  7. Carefully tighten the top cap bolt (M6 x 30mm bolt) according to the manufacturer’s recommendations for the headset.
  8. Install Doormat 2 remote with locking tool.

INSTALLING REMOTE CONTROL ON HANDLEBAR

  1. Install handlebar clamp in the desired location on the handlebar.
  2. Align the Doormat 2 top cap to the top of the handlebar clamp.
  3. Install, but do not fully tighten, M6 x 30mm bolt.
  4. Install Doormat 2. Set the top cap mount to your desired position.
  5. Remove the Doormat 2 with the locking tool.
  6. Carefully tighten the top cap bolt (M6 x 30mm bolt) to the handlebar clamp.
  7. Install Doormat 2 remote with locking tool.

12 SPEED PRODUCTS DOORMATE2 Garage Door Opener - REMOTE
CONTROL1

HOW TO USE THE REMOTE CONTROL

Press and hold the REMOTE BUTTON down until the door or gate starts to move. Installations and conditions vary, contact an installing dealer for more information.

12 SPEED PRODUCTS DOORMATE2 Garage Door Opener - REMOTE
CONTROL2

BATTEY

The LED(s) on your remote control will stop flashing when the battery is low and needs to be replaced. To replace battery, open the case as shown. Remove the Doormat 2 remote from the top cap with the locking tool(1). Unscrew end cap counter-clockwise to expose the battery tray(2). Insert battery positive side down(+) in the end cap. Replace only with CR2032 battery(3). Dispose of old battery properly.

12 SPEED PRODUCTS DOORMATE2 Garage Door Opener -
BATTEY

NOTICE: To comply with FCC, adjustment or modifications of this receiver and/or transmitter are prohibited ,except for changing the code setting or replacing the battery.
THERE ARE NO OTHER USER SERVICEABLE PARTS.
FCC Statement:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the
FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
WARNING
To prevent possible SERIOUS INJURY or DEATH:

  • NEVER allow small children near batteries.
  • If battery is swallowed, immediately notify doctor.
  • Replace ONLY with CR2032 battery.
  • DO NOT recharge, dissemble, heat above 212° F (100° C) or incinerate.

WARRANTY

ONE YEAR LIMITED WARRANTY
Twelve Speed Products warrants to the first consumer purchaser of this product that it is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase.

www.12speed.co

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals