SUNITEC BS007 Bluetooth Neckband Headsets User Manual

SUNITEC BS007 Bluetooth Neckband Headsets User Manual

Product Overview

Bluetooth Pairing

• Step 1: Ensure the headset is ON.
• Step 2: Press and hold MF-Button for 5 seconds until LED indicator flashes blue and red alternately. Once powered on and failed to connect with a phone, it will auto into pairing mode after 10 seconds.
• Step 3: Activate Bluetooth on your phone and select “BS007”
• Step 4: The Bluetooth neckband headset is ready for use now

Noted: After the BS007 Bluetooth neckband headsets and a mobile phone have been paired they will automatically connect with knows mobile phone or Bluetooth device when turned on next time (Bluetooth activated and in range).

How to use

Button for 2seconds (in standby mold & connected with phone)
Redialing last number| Double-tap MF-Button
Restore to default setting| Press and hold V+ / V- for 10 seconds simultaneously
V+| Volume Up| Tap V+ once
Next song| Press and hold V+ for 2s
V-| Volume Down| Tap V- once
Previous song| Press and hold V- for 2s

LED indicator on headset

Pairing
Blue Led flash once every 6 seconds| Standby mode (a phone or Bluetooth device has connected with our BS007)| Connected
Steady red| Battery is charging| N/A
RED OFF| Battery is full charged| N/A
Red Led flash once every 6 seconds| Low battery| **** Low battery
Blue Led flash once every 1 second| Out of Bluetooth range| Disconnected
Blue Led flash once every 6 seconds| Manual disconnect Bluetooth from BS007| Disconnected

How to charge

When the battery becomes low, the Led will flash red every 6 seconds and you will hear voice guidance of “low battery”, then you should recharge your BS007. please charge by using the good quality charger, USB charger or PC USB port. It normally take about 2 hours to full charge the battery. the Led will indicate red when charging and off when charging is complete.

Charging requirements: you can plug our supplied USB cable to your own USB chargers (wall charger/travel charger, etc) with 5V/500Ma-1A or PC USB port. It is OK to use most mobile phone charger on the market.

Warnings

1. Please do not overuse this earphone or put it under heavy pressure, keep away from wet and heat.
2. Keep away from WIFI, router or other high frequency transmitting equipment to prevent interruption of signal receiving
3. Please use this earphone under its working range(10meters), and the effect would be better if there is no obstacle between the connected devices
4. Using this Bluetooth earphone to connected any device with Bluetooth function

Technical specifications

• Bluetooth V5.0, Qualcomm chipset, Up to 10 meters (33 feet)
• Operating frequency band: 2402~2480MHz unlicensed LSM band
• Paired device: Up to 8 paired devices, two active device connected simultaneously
• Battery: Built-in 200mAh rechargeable Li-ion battery
• Standby time: Up to 250 hours
• Talk   time: Up to 12-15 hours
• Supported profile: HSP, HFP, A2DP, AVRCP, APTX, APTX Low Latency, SBC, AAC
• Charging time: approx.2hours
• Charger Voltage: DC5.0V, 500mA

Note: The talk and stand by time may vary when using different phones or other compatible Bluetooth device, usage setting usage style and environments.

Declaration of Conformity

The company Sunitec Electronics Limited, declares that products BS007 complies with the essential requirement of the 2014/53/EU
The declaration of conformity in complete form is available at the headquarters of Sunitec Electronics Limited.
Product sold in the US and Product sold in the European community Manufactured by Sunitec Electronics Limited.

MADE IN CHINA

For FAQs and more information, pleae visit:

Web: www.sunitec.net
 [email protected]
 +86-755-36863386/36863387/36863389

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
The equipment conforms to the RF specification and the use is not restricted.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>