Xiamen New Sound Technology BW Neckband Hearing Amplifier User Manual
- June 6, 2024
- Xiamen New Sound Technology
Table of Contents
Xiamen New Sound Technology BW Neckband Hearing Amplifier
THANKS
Congratulations! Welcome to a New Life created by wireless neckband hearing amplifier. Please read this manual carefully before use.
Intended use
This package includes wireless neckband hearing amplifier. Our neckband
hearing amplifier is designed for every occasion strong noise filter feature.
Configuration
Neckband Hearing Amplifier
- Earphone
- Microphone
- Charging port
- Volume up
- Volume down
- Indicator light
- On/off switch
- Multi-function button
- Dome
How to Use
Charge with Micro-USB cable
Charging the hearing amplifier is similar to charging a cellphone.
a) Plug the larger end of the charging cable into the adaptor.
b) Plug the smaller end into the USB port on the device.
c) Plug the adaptor into a power outlet.
| Charging time| Charging indicator|
Fully charged indicator
---|---|---|---
Neckband hearing amplifier
|
≤ 3 hours
| |
| Low battery indication
The device will emit voice indicator”please charge” to remind you to charge
the device when it is in low battery condition.
---|---
| Notice:
a) The devices contain built-in and non-removable rechargeable lithiumion
battery.
b) Before using your amplifier for the first time, it is recommended to
have the device fully charged.
---|---
Power on and off
Power on
Turn on the neckband hearing amplifier by pushing up the On-off button.
You will hear voice indicator “Power on”when the device turned on.
Power off
Turn off the neckband hearing amplifier by pushing down the On-off button.
You will hear voice indicator “Power off” when the device turned off.
How to wear
- As shown above, slightly lift both ends of the device over the head, wear around the neck with control panel facing up.
- Insert the earphones into both ears.
| The volume was preset after production. It’s recommended to firstly adjust
volume according to your individual need
---|---
Adjust volume
As shown above, short press “volume+” to increase volume, short press
“volume-” to decrease volume.
Attention: There are total of nine levels of volume. When reach the minimum or maximum volume level, you will hear three beeps indicator.
How to connect with your smart phone
- Automatically enter the connecting state after booting.
- Enable the Bluetooth on smart phone and connect with “BW52”.
- 1f unsuccessful connection within 1 minute, need to restart.
How to use Multi-function button
- Can only be activated when connected to a smart phone;
- When connected to mobile phone, single click to start/pause music;
- Phone incoming call, single click to answer/hang up the call; long press for 2s to reject the call;
- Connected to the mobile phone, short press twice to call the nearest outgoing call.
Quick operate the core function
| Press
once| Music listening play/pause
| Press
once| Answer/Hang up phone call
| Hold
for 2 seconds| Reject call
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (l)this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF warning for Portable device:.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>