metabo W 22-180 MVT Cordless Angle Grinder Instructions

W 22-180 MVT W 22-230 MVT WE 22-180 MVT WE 22-230 MVT
WE 22-230 MVT Quick W 24-180 MVT **W 24-230 MVT WE 24-180 MVT WE 24-230 MVT
WE 24-230 MVT Quick WEA 24-180 MVT Quick WEA 24-230 MVT Quick
WEPB 24-230 MVT Quick WEPBA 24-180 MVT Quick WEPBA 24-230 MVT Quick
W 26-180 MVT W 26-230 MVT WE 26-230 MVT Quick WEA 26-230 MVT Quick WEPBA 26-230 MVT Quick **

W 22-180 MVT Cordless Angle Grinder

****2) 2014/30/EU, 2006/42/EC, 2011/65/EU
3) EN 60745-1:2009+A11:2010, EN 60745-2-3:2011+A2:2013+A11:2014+A12:2014+A13:2015, EN IEC 63000:2018
2021-06-17, Bernd Fleischmann, Vice President Product Engineering & Quality
*4) Metabowerke GmbH – Metabo-Allee 1 – 72622 Nuertingen, Germany

Original instructions

Declaration of Conformity
We, being solely responsible: Hereby declare that these angle grinders, identified by type and serial number 1), meet all relevant requirements of directives 2) and standards 3). Technical documents for 4) – see Page 3.
For UK only:
We as manufacturer and authorized person tocompile the technical file, see 4) on page 4, hereby declare under sole responsibility that these angle grinders, identified by type and serial number1) on page 3, fulfill all relevant provisions of following UK Regulations *2) S.I. 2016/1091, S.I. 2008/1597, S.I. 2012/3032 and Designated Standards EN 60745-1:2009+A11:2010, EN 60745-2-3:2011+A2:2013+A11: 2014+A12: 2014+A13:2015, EN IEC 63000:2018.

Specified Use

Machines fitted with original Metabo accessories are suitable for grinding, sanding, abrasive cuttingoff operations and wire brushing metal, concrete, stone and similar materials without the use of wate
The user bears sole responsibility for any damage caused by inappropriate use.
Generally accepted accident prevention regulations and the enclosed safety information must be observed.

General Safety Instructions

**For your own protection and for the protection of your power tool, pay attention to all parts of the text that are marked with this symbol!
WARNING – Reading the operating instructions will reduce the risk of injury.
WARNING** Read all safety warnings and instructions. Failure to follow all safety warnings and instructions may result in electric shock, fire and/or serious injury.
Keep all safety instructions and information for future reference. Pass on your power tool only together with these documents.

Special Safety Instructions

4.1 Safety Warnings Common for Grinding, Sanding, Wire Brushing or Abrasive Cutting-Off Operations:
Use
a) This power tool is intended to function as a grinder, sander, wire brush or cut-off tool. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
b) Operations such as polishing are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.
c) Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.
e) The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.
f) Treaded mounting of accessories must match the grinder spindle thread. For accessories mounted by flanges, the arbour hole of the accessory must fit the locating
diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush
for loose or cracked wires. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally  reak apart during this test time.
h) Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation.
j) Hold power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
k) Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory.
I) Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control.
m) Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards.
o) Do not operate the power tool near flammable materials. Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.
4.2 Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding. For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.
a) Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory. Accessory may kickback over your hand.
c) Do not position your body in the area where power tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create frequent kickback and loss of control.
4.3 Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations:
a) Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe.
b) The grinding surface of the centre depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.
c) The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect operator from broken wheel fragments and accidental contact with wheel and sparks which could ignite clothing.
d) Wheels must be used only for recommended applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.
e) Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.
f) Do not use worn down wheels from larger power tools. Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst.
4.4 Additional Safety Warnings Specific for Abrasive Cutting-Off Operations:
a) Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.
b) Do not position your body in line with and behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. Investigate and take corrective action to eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully reenter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece.
e) Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge ofthe workpiece on both sides of the wheel.
f) Use extra caution when making a “pocket cut” into existing walls or other blind areas. Theprotruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback
4.5 Safety Warnings Specific for Sanding Operations:
a) Do not use excessively oversized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback.
4.6 Safety Warnings Specific for Wire Brushing Operations:
a) Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush. The wire bristles can easily penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wirebrushing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work load and centrifugal forces.
4.7 Additional Safety Instructions:
WARNING – Always wear protective goggles.
Use elastic cushioning layers if they have been supplied with the grinding media and if required. Observe the specifications of the tool or accessory manufacturer! Protect the discs from grease or impacts!
Grinding discs must be stored and handled with care in accordance with the manufacturer’s instructions.
Never use parting grinder discs for roughing work!
Do not apply pressure to the side of parting grinderdiscs.
The workpiece must lay flat and be secured againstslipping, e.g. using clamps. Large workpieces mustbe sufficiently supported.
If accessories with threaded inserts are used, the end of the spindle may not touch the base of the hole on the grinding tool. Make sure that the thread in the accessory is long enough to accommodate the full length of the spindle. The thread in the accessory must match the thread on the spindle.
See page 3 and chapter 14. Technical
Specifications for more information on the spindle length and thread.
Use of a fixed extractor system is recommended.
Always install an RCD with a max. trip current of 30 mA upstream. If the angle grinder is shut down via the RCD, it must be checked and cleaned. See chapter 9. Cleaning.
Damaged, eccentric or vibrating tools must not be used.
Avoid damage to gas or water pipes, electrical cables and load-bearing walls (static).
Pull the plug out of the socket before making any adjustments, converting or servicing the machine.
A damaged or cracked additional handle must be replaced. Never operate a machine with a defective additional handle.
A damaged or cracked safety guard must be replaced. Never operate a machine with a defective safety guard.
Do not switch on the machine if tool parts or guard devices are missing or defective.
Machines with a soft start (indicated by “WE” in the model designation): An electronic error occurs if the machine accelerates to maximum speed very quickly when switched on. Other safety-related electronic functions are no longer available. Have the machine repaired immediately (see 12.).
Secure small workpieces. For example, clamp in a vice.
Reduce dust exposure:
Some dust created by using this power tool may contain chemicals known to cause cancer, allergic reaction, respiratory disease, birth defects or other reproductive harm. **** Some examples of these chemicals are: Lead from leadbased paints, crystalline silica from bricks and cement and other masonry products, Arsenic and chromium from
chemically-treated lumber, hard wood like oak or beech, Metals, Asbestos. The risk from these exposures depends on how long you or bystanders are being exposed.
Do not let particles enter the body. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as dust masks
that are specially designed to filter out microscopic particles. Observe the relevant guidelines for your material, staff, application and place of application (e.g. occupational health and safety regulations, disposal). Collect the generated particles at the source, avoid deposits in the surrounding area. Use suitable accessories for special work (see chapter 11.), thus less particles enter the environment in an uncontrolled manner. Use a suitable extraction unit. Reduce dust exposure with the following measures:

• Do not direct the escaping particles and the exhaust air stream at yourself or nearby persons or on dust deposits.
• Use an extraction unit and/or air purifiers
• Ensure good ventilation of the workplace and keep clean using a vacuum cleaner Sweeping or blowing stirs up dust
• Vacuum or wash the protective clothing Do not blow, beat or brush

Overview

See page 2.

1. Quick”clamping nut *
2. Support flange *
3. Spindle
4. W…A…: Autobalancer support flange (nondetachable)*
5. Spindle locking button
6. Electronic signal indicator *
7. Lock (to prevent the machine from being switched on unintentionally, or for continuous operation)*
8. Trigger (for switching on and off)
9. Button (to turn the main handle)
10. Main handle
11. Additional handle/Additional handle with vibration damping
12. Safety cover
13. Adjusting nut *
14. 2-hole spanner *
15. Quick-release clamp (to adjust safety guard without the use of tools)
16. Screw (to adjust clamping force of quickrelease clamp) * depending on equipment/not in scope of delivery

Commissioning

Before plugging in, check that the rated mains voltage and mains frequency, as stated on the rating label, match with your power supply.
Always install an RCD with a max. trip current of 30 mA upstream.
Use only extension cables with a min. cross-section of 1.5 mm²
Extension cables must correspond to the power consumption of the machine (cf Technical Specifications). If a cable roller is used, always roll up the cable completely.
6.1 Attaching the additional handle
** Always work with the additional handle (11) attached! Manually screw in the additional handle securely in the left, centre or right threaded
hole (depending on requirements).
6.2 Attach the safety guard**
(for working with abrasive discs) Prior to operation: Attach safety guard.

For reasons of safety, the safety guard (12) should always be attached when roughing work is performed.
For reasons of safety, the special parting guard should always be attached before parting work is performed (see chapter 11. Accessories).
See illustration F on page 2. – Open quick-release clamp (15). Mount the safety guard (12) in the position indicated.

• Turn the safety guard until the closed section is facing the operator.
• Close quick-release clamp.
• If necessary, increase clamping force of quickrelease clamp by tightening the screw (16) (with opened quick-release clamp).

Use only accessories that are covered by at least
3.4 mm by the safety guard.

6.3 Pivotable main handle
Only work with the main handle (10) engaged.
See illustration C on page 2.

• Push in the button (9).
• The main handle (10) can now be turned 90° to both sides and can be engaged.
• Make sure that it is securely positioned: the main handle (10) must be engaged and it should not be possible to move it.

6.4 Power-supply connection
The mains sockets must be protected using timedelay fuses or circuit breakers. Machines with “WE…” in the model designation: (with inbuilt automatic startup- current limitation(soft start).) The mains sockets can also be protected using fast-acting fuses or circuit breakers.

Attaching the grinding disc

Prior to any conversion work: Pull the mains plug from the socket. The machine must be switched off and the spindle at a standstill.
For reasons of safety, attach the parting guard before performing parting work (see chapter 11. Accessories).

7.1 Locking the spindle
Press in the spindle locking button (5) only when the spindle is stationary!
– Press in the spindle locking button (5) and turn the spindle (3) by hand until the spindle locking button engages.
7.2 Placing the grinding wheel in position
See illustration D on page 2.
Machines with the designation W 2…, WE 2…:

• Fit the support flange (2) on the spindle. The flange should not turn on the spindle when properly attached.
• Position the grinding wheel on the support flange (2) as shown in illustration D.
  The grinding disc must lay flat on the supporting flange.

Machines with the designation W…A 2…:
The Autobalancer support flange (4) is permanently fitted on the spindle. As is the case with most other angle grinders, a detachable support flange is not necessary.
The contact surfaces of the Autobalancer support flange (4), grinding wheel and the Quick-Stop adjusting nut (1) or other adjusting nut (13) must be clean. Clean if necessary.
– Place the grinding wheel on the Autobalancer support flange (4). The grinding wheel must lie flat on the Autobalancer supporting flange.

7.3 Securing/Releasing the “Quick”
clamping nut (depending on features)
Securing the “Quick” clamping nut (1):
Do not use the “Quick” clamping nut if the accessory has a clamping shank thicker than 8 mm! In this case, use the clamping nut (13) with 2hole spanner (14).
Only use the “Quick” clamping nut when undamaged and in perfect operating condition: the arrow must point to the notch on the outer ring (see illustration on page 2).

• Lock the spindle (see chapter 7.1).

• Fit the “Quick” clamping nut (1) on the spindle (3).
  See illustration on page 2.

• Tighten the “Quick”clamping nut by turning clockwise by hand.

• Turn the grinding wheel firmly clockwise to tighten the “Quick”clamping nut.
  For machines with the designation W…B… an increased resistance is to be felt on the last 180°.
  Releasing the clamping nut (1):

• Lock the spindle (see chapter 7.1).

• Turn the “Quick”clamping nut (1) anticlockwise to unscrew.

7.4 Securing/Releasing the clamping nut (depending on features) Securing the clamping nut (13):

The 2 sides of the clamping nut are different. Screw the clamping nut onto the spindle as follows: See illustration E on page 2.
A) For thin grinding discs:
The edge of the clamping nut (13) faces upwardso that the thin grinding disc can be attached securely.
B) For thick grinding discs:
The edge of the clamping (13) faces downwardsso that the 2-hole nut can be attached securely to the spindle.
Locking the spindle. Turn the clamping nut (13) clockwise using the 2-hole spanner (14) to secure.
For machines with the designation W…B… an increased resistance is to be felt on the last 180°.
Releasing the clamping nut:
– Lock the spindle (see chapter 7.1). Turn the clamping nut (13) anticlockwise using the 2-hole spanner (14) to unscrew.

Use

8.1 Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the accessory towards the workpiece.
Avoid inadvertent starts: always switch the tool off when the plug is removed from the mains socket or if there has been a power cut.
In continuous operation, the machine continues running if it is forced out of your hands. Therefore, always hold the machine with both hands using the handles provided, stand securely and concentrate.
Avoid the machine swirling up or taking in dust and chips. After switching off the machine, only place it down when the motor has come to a standstill.
See illustration A on page 2.
Torque activation
Switching on: Slide the lock (7) in the direction of the arrow and press the trigger switch (8).
Switching off: Release the trigger switch (8).
Continuous operation (depending on features)
Switching on: Slide the lock (7) in the direction of the arrow, press the trigger switch (8) and keep it pressed. The machine is now switched on.
Now slide the lock (7) in the direction of the arrow once more to lock the trigger switch (8) (continuous operation).
Switching off: Press the trigger switch (8) and release.
Machines with the designation W…B:
Torque activation (with dead man’s lever) See illustration B on page 2.
Switching on: Slide the trigger switch (8) forwards and then push the trigger switch (8) upwards.
Switching off: Release the trigger switch (8).
8.2 Working Directions Grinding:
Press down the machine evenly on the surface and move back and forth so that the surface of the workpiece does not become too hot.
Rough grinding: position the machine at an angle of 30° – 40° for the best working results.
Cutting-off operations:
Always work against the run of the disc (see illustration). Otherwise there is the danger of the machine kicking back from the cut out of control. Guide the machine evenly at a speed suitable for the material being processed. Do not tilt, apply excessive force or sway from side to side.
Sanding:
Press down the machine evenly on the surface and move back and forth so that the surface of the workpiece does not become too hot.
Wire brushing:
Press down the machine evenly.

Cleaning

Cleaning the motor: It is possible that particles deposit inside the power tool during operation. This impairs the cooling of the power tool. Conductive build-up can impair the protective insulation of the power tool and cause electrical hazards.
The power tool should be cleaned regularly, often and thoroughly through all front and rear air vents using a vacuum cleaner or by blowing in dry air. Prior to this operation, separate the power tool from the power source and wear protective glasses and dust mask.
Button (9) for adjusting the handle: Occasionally blow compressed air through the button (when pressed, in all 3 main handle positions). Prior to this operation, separate the power tool from the power source and wear protective glasses and dust mask.

Troubleshooting

Machine with “WE…” in the model designation:

• Overload protection: The electronic signal display (6) lights up and the load speed decreases dramatically. The motor temperature is too high! Run the machine in idling until it cools down and the electronic signal display switches off.

• Overload protection: The electronic signal display (6) lights up and the load speed decreases slightly. The machine is overloaded.
  Work with a reduced load until the electronic signal display goes out.

• Electronic safety stop: The electronic signal display (6) lights up and the machine was SWITCHED OFF automatically. If the slew rate of the current is too high (for example, if the machine suddenly seizes or kickback occurs), the machine switches off. Switch off the machine at the trigger switch (8). Switch it on again and continue to work as normal. Try to prevent the machine from seizing. See Section 4.2.

• Restart protection: The electronic signal display (6) FLASHES and the machine does not start. The restart protection is active. If the mains plug is inserted with the machine switched on, or if the power supply is restored following an interruption, the machine does not start up. Switch the machine off and on again.

• When switched on, the machine accelerates to maximum speed very quickly, i.e. automatic restriction of the starting current does not work (soft start). An electronic error exists. Other safety-related electronic functions are no longer available. Have the machine repaired immediately (see 12.).
  W 22-180 MVT, W 22-230 MVT, W 24-180 MVT, W 24-230 MVT, W 26-180 MVT, W 26-230 MVT:

• Switching on the machine reduces the voltage briefly. Unfavourable mains power conditions may have a detrimental effect on other machines. Power impedances less than 0.2 ohm should not cause malfunctions.

Accessories

Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements and specifications listed in these operating instructions.
Fit accessories securely. Secure the machine if it is operated in a bracket. Loss of control can cause personal injury.
See page 4.
A Roughing disc (always use with safety guard attached)
B Lamellar grinding disc (always use with safety guard attached)
C Parting safety guard.
D Parting disc (always use with parting safety guard attached)
E Diamond discs (always use with safety guard or parting safety guard attached)
F Cup wheel guard (place on machine and secure with screws (f)). Secure cup wheel as described in chapter 7.. Use an offset 2-hole spanner if necessary. Use the wing screws to adjust the safety guard until the cup wheel protrudes max. 3 mm.(
G Cup wheels (When working with cup wheels, the special cup wheel guard has to be used for safety reasons.)
H Offset 2-hole spanner (for securing/loosening the clamping nut (13) on cup wheels)
I Parting safety guard with guide slot (place on machine and secure with screws.) (with adapter for connection to a suitable dust extractor for extraction of stone dust  enerated when cutting stone slabs.)
J Hand guard (for attaching under the additional side-mounted handle.)
K Extension piece (for working with supporting discs. Increases the distance between the spindle and the supporting disc by approx. 35 mm)
L Supporting disc for fibre discs (always attach using the supporting disc clamping nut supplied.) (always use with the hand guard attached.)
M Fibre discs (always use with the hand guard attached.)
N Steel wire brushes (always use with the hand guard attached.)
O Bench cut-off stand
P Adjusting nut (13)
Q “Quick” clamping nut (1)
For the complete range of accessories, see www.metabo.com or the main catalogue.

Repairs to electrical tools must be carried out
by qualified electricians ONLY!

Repairs

**** Repairs to electrical tools must be carried out by qualified electricians ONLY!
A defective mains cable must be replaced only with a special, original mains cable from Metabo available from the Metabo service.
For machines with the designation W…B… the braking pad also needs to be replaced when replacing the carbon set.
Contact your local Metabo representative if you have Metabo power tools requiring repairs. For addresses see www.metabo.com.
You can download a list of spare parts from www.metabo.com.

Environmental Protection

The generated grinding dust may contain harmful substances. Dispose appropriately. Observe national regulations on environmentally compatible disposal and on the recycling of disused machines, packaging and accessories.
**** Only for EU countries: Never dispose of power tools in your household waste! In accordance with European Directive 2012/ 19/EU on waste electrical and electronic equipment and its implementation in national legal systems, used power tools must be collected separately and handed in for environmentally compatible recycling.

Technical Specifications

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
Dmax = max. diameter of the accessory
tmax,1 = max. permitted thickness of clamping shank on accessory when using clamping nut (13)
tmax,2 = max. permitted thickness of clamping shank on accessory when using “Quick” clamping nut (1)
tmax,3 = roughing disc/cutting disc: max. permitted thickness of accessory
M=spindle thread l = length of the grinding spindle
n = no-load speed (maximum speed) P1 =rated input power
P2 = power output
m = weight without mains cable
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~ AC Power
The technical specifications quoted are subject to tolerances (in compliance with the relevant valid standards).
Emission values
** These values make it possible to assess the emissions from the power tool and to compare different power tools. Depending on the operating conditions, the condition of the power tool or the accessories, the actual load may be higher or lower. For assessment purposes, please allow for breaks and periods when the load is lower. Based on the
adjusted estimates, arrange protective measures for the user e.g. organisational measures.
Vibration total value (vector sum of three directions) determined in accordance with EN 60745:
ah, SG = Vibration emission value (surface grinding)
ah, DS = Vibration emission value (disc sanding)
Kh,SG/DS = Uncertainty (vibration)
Typical A-effective perceived sound levels:
LpA =Sound-pressure level
LWA = Acoustic power level
KpA, KWA = Uncertainty
Wear ear protectors!**

Metabowerke GmbH
Metabo-Allee 1
72622 Nuertingen
Germany
www.metabo.com

References

• Metabo - Power Tools for professional users
• Metabo - Elektrické nářadí pro profesionální uživatele

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>