Sunday Living GD9215BCP-4BJ Cabinet Infrared Heater User Manual
- June 6, 2024
- Sunday Living
Table of Contents
Sunday Living GD9215BCP-4BJ Cabinet Infrared Heater
MODEL: GD9215BCP-4BJ
Thank you for purchasing your new heater.
These operating instructions will help you use it properly and safely.
We recommend that you spend some time reading this instruction manual in order
that you fully understand all the operational features it offers.
Read all the safety instructions carefully before use and keep this
instruction manual for future reference
Facebook: #SundayLiving Message: #SundayLiving
Email:
[email protected]
INTRODUCTION
Please take a few minutes to read this manual carefully.
Proper maintenance and operation of this machine can provide better service.
WARNINGS
- Read ALL instructions before using this unit.
- CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself.
- This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater.
- Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and curtains at least 3 ft from the front of the heater and keep them away from the sides, top, and rear. DO NOT place towels or other objects on the heater.
- Extreme caution is necessary when any heater is used by or near children or the disabled, or when the heater is left operating and unattended.
- DO NOT operate any heater with a damaged cord or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
- This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER locate heater where it may fall into a bathtub or other water container. To protect against electrical hazards, DO NOT immerse in water or other liquids.
- DO NOT touch the control panel or plug with a wet hand.
- DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
- DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. DO NOT use in areas where gasoline, paint, explosive and/or flammable liquids are used or stored. Keep unit away from heated surfaces and open flames.
- Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
- To avoid fire or shock hazard, plug the unit directly into a 120 V AC electrical outlet.
- To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull firmly on the plug, DO NOT unplug by pulling on the cord.
- Always unplug the unit before moving or cleaning, or whenever the heater is not in use.
- Use only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by unauthorized dealers may cause hazards.
- Always use on a dry, level surface. Use on floor only.
- DO NOT use outdoors.
- To reduce the risk of fire or electric shock, DO NOT use this unit with any solid-state speed control device.
- DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. Qualified personnel should perform all servicing only.
- Connect to properly grounded outlets only.
- Save these instructions.
SPECIFICATION
| Voltage Rating | 120 V (60Hz) |
|---|---|
| Power Consumption | 1500W |
| Unit Size | 10.2 i n. (D) × 11 in. (W) × **13.7 in. |
(H)
Unit Weight| 9.4 lb**
SAFETY FEATURES
Tip-Over Safety Feature
This heater is equipped with a tip-over safety feature. Once the heater is
tipped over, an internal switch will automatically shut the heater off. Once
the heater is restored an upright position, the heater will reset. To continue
operation, turn on the heater using the supplied remote control or the control
panel on the heater.
Overheat Safety Feature
This heater is equipped with a overheat safety feature. When the heaters
internal components reach a certain temperature that could cause overheat and
possible fire, the heater will automatically shut off.
WARNING: This heater has a voltage rating of 120 volts. The cord has a
plug as shown in A. An adapter as shown in C is available for connecting
three-blade grounding-type plugs to two-slot receptacles. The grounding lug
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box. The adapter should not be used if a three-slot
grounded receptacle is available.
DO NOT DEFEAT THE SAFETY PURPOSE OF THE GROUNDED PLUG.
WARNING: It is normal for the power cord to feel warm to the touch;
however, a loose fit between the outlet and the plug may cause overheating of
the plug. If this occurs, try inserting the plug into a different outlet.
Contact a qualified electrician to inspect the original outlet for damage.
PRODUCT DIAGRAM
- ON/OFF button: Powers the display on and off.
- Mode button：To select between High、Low and Eco modes.
- Temp up button: To increase the desired temperature.
- Signal receiving window: For receiving the remote control signal.
- Temp down button: To decrease the desired temperature.
- ℃/℉Button: Alternates between Fahrenheit and Celsius.
- Timer button：Used to engage timer mode and to set hour value for the timer.
- Timer indication light：Will be lit when the Timer mode is engaged.
- Celsius indicator light: Will be lit when the temperature displayed is in Celsius.
- Fahrenheit indicator light: Will be lit when the temperature displayed is in Fahrenheit.
- Digital display：Indicate set room temperature or time or ‘OF’ when turning on the power switch.
- Energy-saving mode indicator: Will be lit when the energy-saving mode is engaged.
- Low Mode indicator light: Will be lit when Low Heat mode is engaged.
- High Mode indicator light: Will be lit when High Heat mode is engaged.
Remote Control
ON/OFF button: Used for power-on or power-off
Temp up button: to make set temperature rise
Temp down button: to make set temperature decline
Mode button：Used for mode selection
℃/℉button: Button for alternating between Fahrenheit and Celsius
Timer button: Used for setting timer and adjust time value of timing
NOTE: Please feel free to contact Service Team for help if the remote control is missing or damaged.
PREPARATION
Place the heater on a firm, level surface and plug into a grounded 120V 60Hz
power outlet. and turn on the power switch in the rear of the unit. Only
operate heater in upright position with caster wheels attached.
Insert 2 AAA batteries into the remote control before using (Batteries Not
Included)
OPERATING INSTRUCTION
Start and select working mode
Setting Desired
Temperature
Setting the POWER OFF TIMER Function
Note: The Power-Off-Timer Function will allow for the heater to power OFF
after a certain set time, and can only be set while the heater’s display is in
the “On”position. 
Setting the POWER-ON-TIMER Function
(Note: The Power-ON-Timer Function will allow for the heater to power ON
after a certain set time, and can only be set while the heater’s display is in
the “Off” position. 
Setting electro lock
The Electro Lock can help avoid the heater from being accidentally engaged
by children. The locking mechanism can be set in both the ON and OFF modes.
MAINTENANCE
- Turn off the power switch in the rear of the unit.
- Unplug the unit and let it cool completely.
- To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth. CAUTION: DO NOT let liquid enter the heater.
- DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to clean the heater. This may cause damage or deterioration to the surface of the heater.
- DO NOT immerse the heater in water.
- Wait until the unit is completely dry before use.
- Air filter needs cleaning after used 3 months of use. Please take off the filter with the 2 steps in the drawing below. Flush and clean the filter with water, Then, dry it out and re-assemble.
If you do not use the heater for a long time, please take out the remote batteries (to prevent corrosion ) as shown below. Store the remote in a safe place.
TROUBLESHOOTING
If the heater will not operate, please check the following before seeking
repair advice:
- Check if the power cord is plugged into an electrical outlet, if not, plug in.
- Check if electricity to the main power switch (in the back) is working.
- Check to see if the battery on the remote is placed correctly, undamaged.
NOTE: For the heater to function properly, the desired temperature on the heater must be set a few degrees higher than the temperature in the room. If the seems to not be heating, increase the desired temperature on the heater to engage the heat elements.
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the original packaging to repack the unit.