TEMPUR-PEDIC RF502A Remote Control User Manual
- June 6, 2024
- TEMPUR-PEDIC
Table of Contents
User Manual of RF502A
Item
1.1 ZG button ⑾
Click the ZG button, the actuator moves to ZG position, stop when clicking any
button during the movement;
Press and hold the ZG button for 5s, timer LED of remote flashes, the control
box records current position as ZG position;
When in the process of moving to memory positions, the head and foot actuators
move first, then the tilt and lumbar actuators move;
1.2 AntiSnore button ⑻
Click AntiSnore button, actuators move to AntiSnore position, stop when
clicking any button during movement;
Press and hold AntiSnore button for 5s, timer LED of remote flashes, the
control box records current position as AntiSnore position;
When in the process of moving to memory positions, the head and foot actuators
move first, then the tilt and lumbar actuators move;
1.3 Head up⑷
Press and hold the HEAD-UP button of the remote, the head actuator moves out,
stop when released ;
1.4 Head down ⑺
Press and hold the HEAD DOWN button of the remote, head actuator moves in,
stop when released ;
1.5 Foot up ⑹
Press and hold FOOT UP button of remote, foot actuator moves out, stop when
released;
1.6 foot down⑼
Press and hold FOOT DOWN button of remote, foot actuator moves in, stop when
released When moving to a flat position, lumbar actuator and tilt actuator
move first after 500ms, head and foot actuators start moving;
1.7 Flat⒀
Click the FLAT button, the bed goes flat, stop when clicking any button during
the process of going flat ;
1.8 Massage head ⑴
Click MASSAGE HEAD button, head massage motor switches massage intensity,
massage intensity switches among 0-1-2-3 ;
1.9 Massagefoot⑶
Click MASSAGE Foot button, head massage motor switches massage intensity,
massage intensity switches among 0-1-2-3;
1.10 Massagemode⑵
Click the MASSAGE Mode button to switch the massage mode.
1.11 Under bed light⑸
Click the under bed light button, the under bed light switch its on/off state;
After the under bed light opens, if do not manually close, it will
automatically turn off after 5 minutes;
1.12 Memory position ⑽ ⑿
Click memory position to move the actuator to the memory position.
The product is the remote control of the bed, and the matching model is
MC120NM. FCC ID:2AK23MC120NM
RF Function:2.4G SRD
Operating Band/Frequency:2403-2480MHz
Antenna Type: PCB antenna
Maximum Antenna Gain:1dBi
Manufacturer: Keeson Technology Corporation Limited
Address: No. 195, Yuanfeng East Road, Wangjiangjing, Xiuzhou District,
Jiaxing City, China 314000
FCC Statement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
FCC Radiation Exposure Statement:
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If his equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
ISED RSS Warning/ISED RF Exposure Statement
ISED RSS Warning:
This device complies with Innovation, Science, and Economic Development Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device.
ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment.The device has been evaluated to meet general RF
exposure requirements.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>