SCREWFIX 6213R Outdoor Up and Down Wall Light with PIR Sensor Stainless Steel User Manual

EAN: 5052931727377 / 5052931727391
Model: 6213R / 3691R

IMPORTANT –
Please read carefully the separate safety guide before use.

Not included

Walking direction
1. High Sensitivity
2. Reduced Sensitivity

Aim the sensor across the path

Protect from rain

Avoid sunlight falling onto the lens of the sensor

Avoid aim to the moving objects

Avoid installing around the heat sources (ie. Air vents, heater…)

Aim to the desired area Avoid reflected surfaces (i.e. Mirror, windows, metal) Mount the sensor perpendicular to the ground

Installation

|
---|---
|
---|---
|
---|---

L = Brown or Red
N = Blue or Black
= Green / Yellow

|
---|---
|
---|---

Use

|
---|---
|
---|---

Maintenance

|
---|---

Guarantee

• We take special care to select high-quality materials and use manufacturing techniques that allow us to create products incorporating design and durability. This product LAP has a manufacturer’s guarantee of 3 years against manufacturing defects, from the date of purchase (if bought in-store) or date of delivery (if bought online), at no additional cost for normal (non-professional or commercial) household use.

• To make a claim under this guarantee, you must present your proof of purchase (such as a sales receipt, purchase invoice, or other evidence admissible under applicable law), please keep your proof of purchase in a safe place. For this guarantee to apply, the product you purchased must be new, it will not apply to second-hand or display products. Unless stated otherwise by applicable law, any replacement product issued under this guarantee will only be guaranteed until the expiry of the original period guarantee period.

• This guarantee covers product failures and malfunctions provided the product was used for the purpose for which it is intended and subject to installation, cleaning, care
  and maintenance in accordance with the information contained in these terms and conditions, in the user manual and standard practice, provided that standard practice
  does not conflict with the user manual.

• This guarantee does not cover defects and damage caused by normal wear and tear or damage that could be the result of improper use, faulty installation or assembly, neglect, accident, misuse, or modification of the product. Unless stated otherwise by applicable law, this guarantee will not cover, in any case, ancillary costs (shipping, movement, costs of uninstalling and reinstalling, labor, etc), or direct and indirect damage.

• If the product is defective, we will, within a reasonable time, replace or refund.

• Rights under this guarantee are enforceable in the country in which you purchased this product. Guarantee-related queries should be addressed to the store you purchased this product from.

• The guarantee is in addition to and does not affect your statutory rights.

****Troubleshooting

circuit breaker/internal wal switch.
The light fixture is not properly attached to the mounting plate if this is a new installation (the pins are not fully seated in the terminal block).| Re- install the light fixture to the base and ensure the pins are fully seated in the terminal block
The circuit wiring is incorrect (if this is a new installation).| Check the wiring connection.  ensure no connections are loose.
The sensor is aimed in the wrong direction. Detection zone not properly targeted| Re-air the sensor to cover the desired area
Check the lamp. If the light has failed replace it.| Ensure that the light bulb is seated correctly in the lEmpholder
Another light source is causing the unit to think it is daylight.| Turn off surrounding lights
The light canes on during the day.| The unit is located in a shaded area.| The Shire a flashlight onto the sensor. If the light turns off then the fixture Is mounted in an area that does not allow enough light to enter the sensor. Relocate the product
LUX knob is set to daylight position.
light setting| Turn the LUX knob Erni-clockwise to suit desired
The unit may be installed in a relatively dark location| During daylight. turn the LUX control slightly anti-clockwise. When lamp extinguishes. enter detection area. if PIR stir activates. adjust LUX further in an anti-clockwise direction and enter the detection zone again. Repeat the above procedure until the sensor does not activate when you enter the detection area.
The light canes and for no apparent reason.| The product is wired through a dimmer or timer| Do not use a dimmer or timer to control the product. Replace the dimmer or timer with a standard on/off wall switch
The ‘SENT control is set too high| Decrease the ‘SENT setting
The wind is moving trees and bushes in the detection zone| Relocate the unit
Cos in the street are being detected| Relocate the unit
Reflective objects (such as the swimming pool) in the Coverage area.| Relocate the unit
Sunlight is falling onto the lens| Mount unit in a sheltered place
Unit is sensing motion in thedetection zone.| Test the motion sensor by covering up the front curved lens with cardboard to block the view. If the light turns off then something in the detection zone is triggering the sensor. Relocate the unit or change the sensitivity (distance) of the sensor.
The coverage area of the sensor is poor.| Choose a suitable location for installing the product. away Iran trees. hot ventilator dust. street lighting and traffic, which may interfere with its operation| Relocate the unit
The lights stay on continuously| The product is wired through a dimmer or timer| Do not use a dimmer or timer to control the product. Replace the dimmer or timer with a standard on/off wall switch
Ensure the unit is not positioned to detect unwanted objects e.g. cars/people using roads/footpaths next to your property. Occasionally. wind may activate the sensor. (Sometimes passages between buidings etc. can cause a “wild tunnel’ effect.)| Relocate the unit
The unit is operated in the mode of the motion sensor being deactivated| To activate the motion sensor
The lights flash on and off| Heat or light from the bulbs may be turning the sensor on and off| Relocate the unit away from the light source.
The sensor is sensing reflected light from the light fixture.| 1. Change the position of the light head to aim light away from the reflecting surfaces.
2. Relocate the unit to a different location where it no longer causes reflected light.
Sensor will not operate at night| The level of ambient light in the area may be too bright to alow operation at the current LUX setting.| During the hours of darkness. adjust the LUX control slowly anticlockwise / clockwise (choose suitable am) until the lamp just Ruminates
Wiring inside electrical came loose.| After turning off the fixture. recamect any loose walrus
No power is being delivered to the fixture.| Check that the circuit breaker and/or wal switch power is on.
Another light source is causing the unit to think it is daylight.| Turn off surrounding lights and/or relocate the wit
Light does not switch off after set time has elapsed| Tine is set for oolong| Reduce tine (TIME knob)
The unit is operated in the mode of the motion sensor being deactivated| To activate the motion sensor
Continuous movement in the detection zone| Charge detection zone/ Relocate the unit
Light being operated in the detection zone causes the sensor to respond as a result of a change in temperature| Charge detection zone/ Relocate the unit
When setting the controls in daylight the detection distance becomes shorter.| Interference by sunlight.| Re-set controls at night.

**** Safety

• These instructions are for your safety. Please read through them thoroughly prior to installation and retain them for future reference.

• All fittings must be installed by a competent person in accordance with local regulations (IET wiring regulation BS7671).

• Check the pack and make sure you have all of the parts listed.

• Remove all packaging, wrap, etc from the product.

• Decide on the appropriate location for your product.

• CAUTION: IP44 is guaranteed when the product is properly installed and sealed.

•  Always avoid the product being located a corrosive environment.

• Always refer to the installation drawing for the orientation of the product.

• The product must be securely fixed to the mounting surface using the screws and wall plugs supplied. The screws and wall plugs supplied are suitable for “masonry” only.

• Other fixings are not supplied and must be purchased.

•  Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.

• IMPORTANT: The fixing point(s) selected must be capable of supporting the full weight of the light fitting.

• We recommend connecting this product to an external / wall switch in order to deactivate the motion detection function if necessary.

• A wiring diagram is for reference only. Always refer to the terminal marking for wiring. Ensure that all electrical connections are tight and that no loose strands are left out of the terminal block.

• Never use the terminal cables to bear the product weight.

•  When the product does not light after installation:

  Ensure there is no electricity failure
  Ensure all the connections are secured

• If you have any doubt about installation/use of this product, consult a qualified electrician.

• Always disconnect the product from mains at least 10 minutes allowing it to cool down before any maintenance or adjustment.

• The operating time depends on the charging performance in the daytime. This would be affected by the environment e.g. weather conditions and location.

• It is recommended to have a regular schedule of care and maintenance to keep the surface condition well.

Technical Data

available)
| Conformity with all relevant EC Directive requirements.
| Conformity with all relevant UK legislation requirements.
| Class I product, must be connected to the earth.
| Minimum distance from lighted objects (0.5 meters)
IP44| Splash-proof
****| Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
| Luminaire designed to be used only with self-shielded tungsten halogen lamps
| Do not use a dimmer switch.
xx yy| xx-year; yy-week of the year

Addresses
Manufacturer • Fabricant • Producent • Fabricant
UK Manufacturer:
Kingfisher International Products Limited,
3 Sheldon Square, London, W2 6PX,
United Kingdom
EU Manufacturer:
Kingfisher International Products B.V.
Rapenburgerstraat 175E
1011 VM Amsterdam
The Netherlands
www.kingfisher.com/products
www.diy.com
www.screwfix.com
www.screwfix.ie
To view instruction manuals online,
visit www.kingfisher.com/products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>