9141 0720 Quebec Dba Manaras Opera 100 Series Rolling Code Transmitters Instructions

9141 0720 Quebec Dba Manaras Opera 100 Series Rolling Code Transmitters

Instructions

Commercial Sequence or SBC Programming (Optional)

Modes

|

Functions

| Programming (On operator’s ECB)
---|---|---

Commercial Sequence – 1-Button

| OPEN / CLOSE ‹ Button

Door is CLOSED:

– Click Button ‹ Door OPENS FULLY

During UPWARD Travel:

– Click Button ‹ Nothing happens

Door is OPENED:

– Click Button ‹ Door CLOSES FULLY

During DOWNWARD Travel:

– Click Button ‹ Door reverses and OPENS FULLY

Door is STOPPED:

– Not possible in this mode. Door is either FULLY OPENED or FULLY CLOSED.

| Standard default mode.

1. Door is in fully CLOSED position.

2. On ECB, verify if the close limit switch is activated (CLOSE LED is ON).

3. On ECB, set select switch on

9 = SBC.

4. On ECB, press “ STOP ” button.

5. On ECB, select run mode

(1, 4, or 5).

Single Button Control (SBC)

Available with the Electronic Control Board (ECB) only.

Alternating Sequence

| OPEN / STOP / CLOSE ‹ Button

Door is CLOSED:

– Click Button ‹ Door OPENS

During UPWARD Travel:

– Click Button ‹ Door STOPS

Door is STOPPED:

– Click Button ‹ Door CLOSES

During DOWNWARD Travel:

– Click Button ‹ Door STOPS

Door is STOPPED:

– Click Button ‹ Door OPENS

Note : If the door is STOPPED for more than 2 minutes, the next movement will be UPWARD regardless of the previous movement.

| 1. Door is in fully CLOSED position.

2. On ECB, verify if the close limit switch is activated (CLOSE LED is ON).

3. On ECB, set select switch on

9 = SBC.

4. On ECB, press “ OPEN ” button.

5. On ECB, select run mode

(1, 4, or 5).

Transmitter Programming: RADIOEM101, RADIOEM102, RADIOEM103, RADIOEM104
The Opera Brand Transmitters can be used as either a 1-Door x 3-Button Transmitter or as a Multiple-Door Transmitter (Commercial Sequence or SBC). Commercial Sequence or SBC settings depend on the operator programming settings. The Transmitters can be re-programmed as needs change.

RADIOEM101| 1-Door

1-Button Transmitter (1)

1.OPEN / STOP / CLOSE ‹ Only Button

|

No initial programming is required.

The Transmitters are ready to be matched to the Receiver of your choice, refer to section Transmitter to Operator Matching (Pairing), p. 3.

RADIOEM104

| 4-Door

4 x 1-Button Transmitter (1)

1. DOOR #1 ‹ Top Left Button

2. DOOR #2 ‹ Top Right Button

3. DOOR #3 ‹ Bottom Left Button

4. DOOR #4 ‹ Bottom Right Button

(1) Each button acts separately as a 1-Button Transmitter.

Commercial Sequence or SBC Programming depends on the Operator Settings , please refer to the Commercial Sequence or SBC Programming instructions, p. 4).

| 1-Door

3-Button Transmitter

(Factory default for RADIOEM103SD)

1. OPEN ‹ Top Button

2. CLOSE ‹ Middle Button

3. STOP ‹ Bottom Button

| 1. Press and HOLD Buttons © and © for 5 sec. The RED LED will BLINK.

You have 15 sec. to complete the configuration or you will need to restart.

2. Release Buttons © and ©.

3. Press Button ©.

4. The RED LED will stop  blinking. Programming is now complete.

RADIOEM102 Mini Key Chain
| 3-Door

3 x 1-Button Transmitter (1) **(Factory default for RADIOEM102 & RADIOEM103MD)**

1. DOOR #1 ‹ Top Button

2. DOOR #2 ‹ Middle Button

3. DOOR #3 ‹ Bottom Button

| 1. Press and HOLD Buttons © and © for 5 sec. The RED LED will BLINK.

You have 15 sec. to complete the configuration or you will need to restart.

2. Release Buttons © and ©.

3. Press Button ©.

4. The RED LED will stop  blinking. Programming is now complete.

RADIOEM103 Single Door (SD) / Multiple Door (MD)
| (1) Each button acts separately as a 1-Button Transmitter.

Commercial Sequence or SBC Programming depends on the Operator Settings , please refer to the Commercial Sequence or SBC Programming instructions, p. 4).

Transmitter Programming: RADIOEM144
The RADIOEM144 Rolling Code Transmitter can be used to control up to 144 doors with Open / Close / Stop function. Two rotary dials (Letters: A to L) and (Numbers: 1 to 12) permit for a proper door selection. The Transmitter can be reprogrammed as needs change.

RADIOEM144

| Multiple Door (up to144 doors) 3-Button Transmitter

1. OPEN ‹ Top Button

2. CLOSE ‹ Middle Button

3. STOP ‹ Bottom Button

|

No initial programming is required.

This Transmitter is ready to be matched to the Receiver of your choice, refer to section Transmitter to Operator Matching (Pairing), p. 3.

Transmitter to Operator Matching (Pairing)
The On-Board Radio Receiver RADIORE101, featuring Rolling Code Technology, is factory installed on all operators equipped with an Electronic Control Board BOARD 070 since November 2013. The Series 100 Transmitters are compatible with the RADIORE101 Receiver, as well as the on-site installation kits RADIOKIT 004/005 (operators prior to November 2013), the External Radio Receivers RADIORE901 /901A /901B and RADIORE102.

Compatible Receivers

1. RADIORE101 (ECB BOAR070) / RADIOKIT004 (RADIOKIT005) (On-site Installation Kits)

2. RADIORE901/901A (RADIORE900/900A)

3. RADIORE901B (RADIORE900B)

4. RADIORE102

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the paty responsible for compliance could void the user’s authority to operate the equipment

NOTE: This device has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, use and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to do correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help

ISED
This device contains a license-exempt transmitter/receiver that comply with Innovation Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following wo conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Matching the Transmitter to the On-Board Radio Receiver RADIORE101 or to the External Universal Radio Receivers RADIORE901/901A/901B
Note: For RADIORE102, consult TN1028 for pairing instructions

To MATCH the Transmitter to the Receiver:
Once the Transmitter has been correctly programmed according to instructions found on p. 1-2, select the Receiver of choice, refer to Figure 1 or Figure 2 and follow the steps below:
For RADIOEM101/102/103/104:

1. HOLD the Receiver’s LEARN button until the LED BLINKS for approx. 2 sec. (frequency of 1 sec. ON / 1 sec. OFF).
2. To program in 3-Button Mode: On the Transmitter, HOLD any button until the Receiver’s LED stops blinking .
3. To program in 3 x 1-Button Mode: On the Transmitter, HOLD the desired button that you want programmed until the Receiver’s LED stops blinking .

For RADIOEM144:

1. Adjust the Transmitter’s rotary dials to the desired positions to permit for the proper door selection.
2. HOLD the Receiver’s LEARN button until the LED BLINKS for approx. 2 sec. (frequency of 1 sec. ON / 1 sec. OFF).
3. On the Transmitter, HOLD any button until the Receiver’s LED stops blinking

Note: You can match 1-Button, 3-Button, 4-Button AND 144-Door Transmitters with the same Receiver. Mix and match any of the Series 100 Transmitters accordingly for your application (ordered separately). One Receiver will accept up to 50 Transmitters.

To DELETE ALL Transmitters from the Receiver’s Memory:
HOLD the Receiver’s LEARN button until the LED BLINKS for approx. 10 sec. (frequency of 1/3 sec. ON / 1/3 sec. OFF).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>