9141 0720 Quebec Dba Manaras Opera AKEYLESS042 390MHz Transmitter Instruction Manual
- June 6, 2024
- 9141 0720 Quebec Dba Manaras Opera
Table of Contents
**9141 0720 Quebec Dba Manaras Opera AKEYLESS042 390MHz Transmitter Instruction Manual
**
SAFETY INSTRUCTION
WARNING
TO REDUCE THE RISK OF SEVERE INJURY OR DEATH TO PERSONS
- READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS
- Locate the Keypad:
- within sight of the door,
- at a minimum height of 5 feet (1 5 m) above floors. landings, steps or any other adjacent walking surface so small children are not able to reach it, and
- away from all moving parts of the door
- Activate the door ONLY when it can be seen clearly, is properly adjusted. and there are no obstructions to the door travel.
COMPONENTS
Preparation
-
Locate the LEARN button on the operators On-Board Radio Receiver, refer to Figure 1 or the operators Installation 8 Instruction Manual.
-
Ensure that the Rotary Selection Switch on the operators Electronic Control Board (ECB) is set to B2 (1), T (4) or TS (5).
Fig.1 Electronic Control Board (ECB) -
Undo the screw from the bottom of the case and remove the back cover from the Keypad to install the AAA battery refer to Figure 2
Fig.2 Keyless042 Battery Installation -
Program the Keypad prior to mounting.
New Installation
Program an Initial PIN
- Enter the factory default PIN ( 0 0 0 0 ] on the Keypad Then press the [ * ] button
- Enter a new PIN (2 to 8 digits) of your choice [ ? ? ? ?] Then press the (*) button
- Re-enter the new PIN [ ? ? ? ? ] to confirm Then press the [ * ] button
The new PIN is confirmed once the Keypad’s backlit LED flashes 3 times and the unit emits a Long beep.
Anti-Theft Feature
The Keypad is designed with a secunly feature to prevent thieves from continuously guessing the PIN If there are 10 consecutive incorrect PIN attempts made by the user. the Keypad will auto-lock itself for a period of 10 minutes Removing the battery will not disengage the anti-theft feature Wail for a period of 10 minutes before resuming to program the Keypad
- The Keypad is ready to receive an input as soon as the unit emits a beep when a button is pressed
Timeout Feature
In the event that more than 15 seconds has elapsed between any two keypad inputs during the programming procedure. the unit will emit an error code of 5 short successive beeps.
- The programming procedure in progress must be restarted.
Keypad Pairing I Programming Instructions
SINGLE Door Mode Programming Instructions
Allow for 1 door to be operated by the Keypad.
Single Door Setting| Pairing|
Testing
---|---|---
- Enter the PIN ( 7 7 7 7 I Then press the following sequence of buttons [ * ] [ 0 ] [ # ]
|
- Press and HOLD the LEARN button on the On-Board Radio Receiver for approx. 2 sec or until the White LED on the Receiver flashes.
- Enter the PIN [ ? ? ? ? ] Then press the [ # ] button
|
- Enter the PIN in [ ? ? ? ? ] Then press the [ # ] button to operate the door
- The Keypad will omit 3 beeps as confirmation
|
- The Keypad will emit 3 beeps as confirmation.
|
- The Keypad will emit 3 beeps as confirmation and the door operator w It activate
MULTIPLE Door Mode Programming Instructions
Allows for a multiple doors (max of 4) to be operated by the Keypad.
Multiple Door Setting| Pairing|
Testing
---|---|---
- Enter the PIN [ ? ? ? ? ] Then press the following sequence of buttons [ * ] [ 9 ] [ # ]
|
- Press and HOLD the LEARN button on the On-Board Radio Receiver for approx 2 sec or until the WHITE LED on the Receiver flashes
- Enter the PIN [ ? ? ? ? ]
- Then press the [ # ] button Then the [ DOOR Number ] (1 to 4)
- Repeat the procedure above for the remaining doors.
| To operate DOOR 1:
Enter the PIN [ ? ? ? ? ] Then press the following sequence of buttons [ #
][ 1 ]To operate DOOR 2:
Enter the PIN [ ? ? ? ? ] Then press the following sequence of buttons [ #
][ 2 ]
To operate DOOR 3:
Enter the PIN [ ? ? ? ? ] Then press the following sequence of buttons [ #
][ 3 ]
To operate DOOR 4 :
Enter the PIN [ ? ? ? ? ] Then press the following sequence of buttons [ #
][ 4 ]
- The Keypad will emit 3 beeps as confirmation.
|
- After each door is programmed the Keypad will emit 3 beeps as confirmation.
|
- The Keypad will emit 3 beeps as confirmation and the appropriate door operator will activate.
Mounting Instructions
- Select a desired location to mount the Keypad at a minimum height of 5 feet (1 5 m).
- Secure the back cover at the desired location with the two anchors and screws provided. refer to Figure 3.
- Re-install the keypad unit to the back cover.
- Gently tighten the screw at the bottom of the case.
Fig.3 Mounting keyloess042
Troubleshooting
Change an Existing PIN
-
Enter the programmed PIN [ ? ? ? ? ] that you want to change on the Keypad
Then press the [ * ] button -
Enter a new PIN (2 to 8 digits) of your chows [ ? ? ? ? ] Then press the [ * ] button
-
Re-enter the new PIN [ ? ? ? ? ] to confirm
Then press the [ * ] button- The new PIN is confirmed once the Keypad’s backlit LED flashes 3 times and the unit emits a long beep.
Reset Keypad to Factory Default Settings (when PIN is unknown or forgotten)
- Remove the AAA battery from the Keypad, refer to Figure 2 p4
- Press and HOLD the [ # ] and [ * ] buttons simultaneously. while inserting the AAA battery in the Keypad. refer to Figure 4 and **Figure 5
Fig.5 Insert Battery
**
* The Keypad will emit a long beep- Release [ # ] and [ * ] buttons
- The beep will stop after several seconds
- The PIN has been reset to the factory default PIN [ 0 0 0 0 ]and pairing between the On-Board Radio Receiver and the Keypad is lost.
- Refer to the instruction on how to Program an Initial PIN on p 2 and the Keypad Pairing / Programming Instructions on p.2.
DELETE On-Board Radio Receiver Memory
- Press and HOLD the Receiver’s LEARN button on the On-Board Radio Receiver for approx 10 sec or until the WHITE LED on the Receiver flashes quickly
- This will clear the pairing of an transmitters (radio remotes and keypads) with the On-Board Rada Receiver.
FCC Statement
This device complies with Part 15 of the FCC Rules Operation is subject to the following two condition.
- this device may not raise harmful interference and
- This device must accept any interference received including interference that may flute undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined y turning the equipment and on, the users is encouraged to try to correct the interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on circuit difference from that to which the receiver is connected.
- Consult the dealer or and experienced radio/TV Technician for help.
ISED
This device complies contains licence-exempt transmitter/receiver that comply with innovation Science and Economic Development Canada’s Licence-exempt RSS(s). Operation is subject to the following two conditions:
- this device may not cause interference and
- this device must accept And interference including interference that may cause undesired operation of the device.
For further information Pleas consult the operator’s installation & Instructions Manual or Contact our technical support Department at 1-800-361-2260
1-800-361-2260
www.manaras.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>