qtx 160.473UK High Power Fog Machine User Manual

: June 6, 2024
: qtx

Table of Contents

Introduction
Unpacking
****
Safety
Cleaning
Placement
Setting up
Setting up
Remote timer control
Wireless remote control
DMX operation
Specifications
Troubleshooting
Effect Fluid Chart
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

QTFX-2000 mkII
HIGH POWER FOG MACHINE
Item ref: 160.473UK
User Manual qtx 160 473UK High Power Fog Machine

Caution: Please read this manual carefully before operating Dama e caused b misuse is not covered b the warrant

Introduction

Thank you for choosing the QTFX-2000 mkII fog machine for stage and events special effects. This product is designed to produce high-power fog effects for stage and theatre shows. Please read these instructions fully in order to gain the best results from this item and avoid damage to the unit through misuse.

Unpacking

Your QTFX-2000 mkII should reach you in good condition and should be supplied with IEC mains lead(s), wired remote timer control, wireless plug-in receiver and key fob remote.
If there are any signs of damage or items missing from the packaging, contact your dealer immediately.

Warning

To prevent the risk of fire or electric shock, do not expose electrical parts to rain or moisture.
If liquids are spilled on areas other than inside the fluid tank, disconnect the mains, allow the QTFX-2000 mkII to dry out, and have it checked by qualified service personnel before further use.
Avoid any impact, dropping, or extreme pressure on the housing.
No user-serviceable parts inside – do not open the case.
Allow the QTFX-2000 mkII to acclimatize to room temperature before operating.
Refer all servicing to qualified service personnel.

Safety Symbol and Message Conventions

| CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN| AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR|

---|---|---|---

| This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit
---|---

****

| This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

Safety

Check for correct mains voltage and condition of the IEC lead before connecting to a power outlet
Check the condition of the remote lead and ensure that it is not trapped
This unit uses a heating element – be aware that parts of the housing may be hot whilst in use!
This unit must be earthed

Cleaning

Use a soft dry or slightly damp to clean the casing
Do not use strong solvents for cleaning the unit
Do not use strong solvents for cleaning the unit
Clean the fog mechanism periodically by operating with distilled water instead of fog fluid
It is also recommended to use fog machine cleaning fluid (160.670UK) periodically

Placement

The QTFX-2000 mkII has a built-in fluid container and should be operated in an upright position.
Ensure that the QTFX-2000 mkII is positioned on a stable, non-slip surface.
Allow adequate space for access to the controls and to avoid straining cables and connections.
When moving or carrying the QTFX-2000 mkII, use the top-mounted handles.

Rear Panel

qtx 160 473UK High Power Fog Machine - figure 1

1. Mains power on/off rocker switch	5. DMX out connection (3-pin XLR)
2. IEC mains inlet & fuse holder	6. DMX channel setting DIP switches
3. Remote timer control connection (5-pin XLR)	7. DMX activity indicator
4. Wireless remote receiver connection (5-pin DIN)	8. DMX in connection

(3-pin XLR)

Setting up

The QTFX-2000 mkII requires fog fluid to create the effect.
It is recommended to use one from the range of qtx fog fluids for best results.
A chart for recommended fluids is included further along in this document.

Unscrew the top cap of the fog fluid tank and remove it to fill with the selected fog fluid
Replace the cap and close securely, ensuring the pipe is fed down to the bottom of the bottle so that a
a consistent flow of fluid is supplied to the machine
Alternatively, a fresh 5l bottle of fluid can be inserted as a direct replacement
Connect the remote timer control to the 5-pin XLR connector on the rear panel (3)
Connect the supplied wireless remote receiver to the 5-pin DIN connector (4) on the rear panel
Connect the IEC mains lead supplied to the rear mains inlet (2)
If controlling via DMX, connect the incoming DMX control signal via the 3-pin XLR labelled DMX IN (8)
Connect any further DMX equipment to the XLR labelled DMX OUT (5)
Set the DMX start address using the rear-panel DIP switches (6) in binary number format
Examples are shown below…

Setting up

Make sure that none of the remote timer control buttons are pressed in at startup
Aim the outlet nozzle toward the area where the effect is required but away from contact with people.
Switch the mains power on (1)
Heat up time for fog effect is usually between 8-10 minutes.
During prolonged use, periodically check that the fluid level is not empty
Switch off when not in use. Unplug from mains if not in use for long periods

Warning: There will be hot surfaces on the housing even after the machine is switched off

Remote timer control

Timer button (latching) – activates the timer control
Continuous button (latching) – overrides timer control for constant fog
Manual button (non-latching) – overrides timer control for fog on demand
Timer indicator – illuminated when the timer function is active
Ready indicator – illuminated when heated up ready to produce fog
Continuous indicator – illuminated when the continuous function is active
Output control – adjusts the amount and density of fog effect
Interval control – adjusts the interval between fog output on timer control
Duration control – adjusts the time length of fog output on timer control

qtx 160 473UK High Power Fog Machine - figure 3

When the machine is ready to operate, the ready light (5) on the remote timer control will illuminate.
You may now press the Manual (3) button for fog on demand – releasing button stops the fog effect
When the ready indicator is off, the QTFX-2000 mkII needs time to re-heat and will not produce fog
For constant fog effect, use the latching Continuous (2) button and the Continuous LED (6) will light
The density of the fog effect can be varied by adjusting the rotary Output control (7)
Pressing the Timer button (1) will activate the hands-free timer function and the timer LED (4) will light
The Interval control (8) adjusts the time between fog effect output in each timer cycle
The Duration control (9) adjusts the length of time that fog is produced in each timer cycle

Wireless remote control

Fog can also be controlled manually by the wireless remote control
The key fob remote is powered by a button cell, replace this with a similar type if discharged
Extend the antenna on the key fob, slide down the front cover
Press one of the key fob buttons to produce fog

DMX operation

The QTFX-2000 mkII can be operated by a single channel of DMX512 control.
Set this address via the rear-panel DIP switches as shown above A value of 0 will give no fog output. A value between 1 and 255 will give full fog output.
When a DMX signal is detected, the DMX indicator (7) will flash when data is being received.

Specifications

Power supply	230Vac, 50Hz (IEC)
Fuse	F1OA (5 x 20mm)
Heating element	2000W
Reheat time	8 to 10 mins (approx.)
Fog output (approx.)	40,000 Cu Ft (1133m3)/ min
Tank capacity	51
Remote control	Wireless remote, wired timer remote, DMX512
Remote cable length	5m
RF Remote frequency	433MHz
DMX connection	3-pin XLR in/out (1-channel)
DMX channels	Single-channel — 0=No output, 1-255=full output
Dimensions	670 x 350 x 260mm
Weight	10kg

Troubleshooting

Warning: Hot components! … Switch off and allow to cool before touching the unit.

No light on the mains switch| Check mains voltage is correct and the socket is switched on
---|---
Check IEC lead is OK and connected properly
Check mains fuse in IEC connector and fuse in plug top
If fuse blowing repeatedly, refer to qualified service personnel
Ready light stays off| Check remote is connected properly
If the light is permanently off, refer to qualified service personnel
Ready light is on but no fog output on manual or
continuous| Check fog fluid level
If the fluid is OK and pumps working, the lines may be blocked
Check that nozzle is not blocked or obstructed
If blocked, clean with fog machine cleaner & distilled water
No fog output on timer function| Ensure timer button is pressed in and timer LED is lit
Check interval, duration, and output control settings — test manually if necessary
No response to DMX| Check that XLR leads are connected properly
Check that the DMX signal is OK by testing on other equipment
Check that the DIP switch settings are set to the correct address
Ensure that the other remote controls are not overriding DMX

qtx 160 473UK High Power Fog Machine - figure 4

This product is classed as Electrical or Electronic equipment and should not be disposed of with other household or commercial waste at the end of its useful life. The goods must be disposed of according to your local council guidelines.

Errors and omissions excepted.
Copyright© 2021 AVSL Group Ltd, Unit 2 Bridgewater Park,
AVSL (Europe) Ltd, Unit 3D North Point House,
Taylor Road, Trafford Park, Manchester. M41 73Q.

AVSL (Europe) Ltd, Unit 3D North Point House,
North Point Bus. Park, New Mallow Road, Cork, Ireland.
160.473UK User Manual