BLU-MB12 Wall Mounted Air Conditioner User Manual
- June 9, 2024
- BLU
Table of Contents
- BLU-MB12 Wall Mounted Air Conditioner
- SAFETY INSTRUCTIONS
- PRODUCT OVERVIEW
- FEATURES
- WHATS INCLUDED
- INSTALLATION
- OPERATION
- FUNCTIONS
- WIFI SETUP AND SMART FEATURES WIFI SETUP
- CHANGING BETWEEN CONNECTION TYPES
- CONTROLLING YOUR DEVICE THROUGH THE APP
- TROUBLESHOOTING
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BLU-MB12 Wall Mounted Air Conditioner
SAFETY INSTRUCTIONS
IMPORTANT!
AIR CONDITIONERS MUST ALWAYS BE STORED AND TRANSPORTED UPRIGHT, OTHERWISE
IRREPARABLE DAMAGE MAY BE CAUSED TO THE COMPRESSOR; IF IN DOUBT WE SUGGEST
WAITING AT LEAST 24 HOURS FOLLOWING INSTALLTION BEFORE STARTING THE UNIT.
- Carefully read the instructions before installing and/or operating the unit.
- This appliance is for indoor use only.
- This unit must be only connected to a 220-240 V / 50 Hz earthed outlet.
- Installation must be in accordance with regulations of the country where the unit is used.
- If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, modified by a qualified electrician.
- This air conditioner has been tested and is safe to use. However, as with any electrical appliance – use it with care.
- Disconnect the power from the appliance before dismantling, assembling or cleaning.
- Avoid touching any moving parts of the appliance.
- Never insert fingers, pencils or any other objects though the guard.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities. It is also not intended for use by those with a lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
- Do not leave children unsupervised with this appliance.
- Do not clean the unit by spraying it or immersing it in water.
- Never connect the unit to an electrical outlet using an extension cord. If an outlet is not available, one should be installed by a qualified electrician.
- Do not operate the unit unless it has been fully installed following the guidance provided within this manual.
- Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not stretched or exposed to sharp objects/edges.
- A damaged supply cord should be replaced by the manufacturer or a qualified electrician in order to avoid a hazard.
- Any service other than regular cleaning or filter replacement should be performed by an authorised service representative. Failure to comply could result in a voided warranty.
- Do not use the appliance for any purpose other than its intended use.
- Avoid restarting the air conditioner unless 3 minutes have passed since being turned off. This prevents damage to the compressor.
- Never use the mains plug as a switch to start and turn off the air conditioner. Use the provided ON/OFF button located on the control panel.
- The appliance should not be installed in laundry or wet rooms.
- The appliance must be installed in a room without sources of ignition (for example: open flames, an operating gas appliance or an operating electric heater).
- The unit must be installed on a solid vertical wall by a competent person. The electricity supply must only be connected after installation is complete.
- R290 refrigerant gas complies with European environmental directives
- R290 has a low GWP (Global Warming Potential) of 3.
- The air conditioner contains about 290g of R290 refrigerant gas.
- Do not install or store in an unventilated space with an area smaller than 15 m per unit. The room must be such as to prevent stagnation of possible leaks of refrigerant gas as there could be a danger of fire or explosion hazard should the refrigerant come into contact with electric heaters, stoves or other sources of ignition.
- If the appliance is installed, used or stored in an unventilated room, the room must be such as to prevent stagnation of possible leaks of refrigerant gas as there could be a danger of fire or explosion should the refrigerant come into contact with electric heaters, stoves or other sources of ignition.
- Refrigerant gas may be odourless.
- Do not use the product and contact the retailer for advice, if damage has occurred to the unit which may have compromised the refrigerant system.
- Any repairs or maintenance must only be carried out on the unit by a suitably qualified engineer. Before opening and servicing the unit the authorized engineer must be in possession of a copy of the manufacturer’s service manual and must follow the safety information contained within it to ensure all hazards are minimized.
- The refrigerant system should not be perforated or punctured.
Energy Saving and Unit Safety Protection Tips
- Do not cover or restrict the airflow from the outlet or inlet grills.
- Keep the filters clean. Under normal conditions, filters should only need cleaning once every three weeks ( approximately). Since the filters remove airborne particles, more frequent cleaning maybe necessary, depending on the air quality.
- For the initial start-up set the fan speed to maximum and the thermostat to 4-5 degree lower than the current temperature. After, set the fan switch to low and set the hemostat to your desired setting.
- To protect the unit, we recommend not using the cool mode when the ambient temperature is higher than 35°C.
NOTE : Some pictures and information may vary from the final product. This is due to continual product improvement.
PRODUCT OVERVIEW
PRODUCT DIAGRAM
- FRONT
- BACK
FEATURES
- Simple operation.
- Self-evaporative function with energy-saving technology.
- Sleek design that seamlessly fits into any style of home.
- The bright LED screen indicates temperature and current mode.
- The on/off timer function allows you to choose when the unit operates.
- WIFI App control provides additional functionality.
- Three fan speeds.
- Four modes to suit your every need including Cooling/ Heating/ Fan / Dry
- Silent running option, perfect for a restful night’s sleep.
WHATS INCLUDED
INSTALLATION
TOOLS REQUIRED
- BEFORE STARTING INSTALLATION, PLEASE ENSURE YOU HAVE ALL SUITABLE EQUIPMENT AVAILABLE AND UNDERSTAND THE STEPS INVOLVED IN INSTALLATION. IF IN ANY DOUBT, PROFESSIONAL ADVICE SHOULD BE SOUGHT.
- THE INSTALLER MUST ENSURE THAT THE PLANNED POSITION OF THE AIR CONDITIONER IS SUITABLE, AND THAT THERE ARE NO CABLES AND PIPES INSIDE THE WALL, AND NO OTHER OBSTRUCTIONS FOXED ON THE WALL, WHICH WOULD PRESENT A DANGER AND/OR PREVENT COMPLETION OF INSTALLATION.
This unit must be installed on an external wall, as it vents directly out of
its rear.and ensure the wall is flat, solid and reliable. Leave at least 10 cm
of space to the left, right and base of the machine.
At least 20cm of space must be left above the unit to help air flow smoothly
and stay away from curtains, plants, faucets, furniture and others appliances
etc.
Paste the supplied installation template paper in position on the wall, ensuring that the reference line is level using a spirit level.
The hole for the drainage pipe must be drilled using a 25mm Drill bit. Ensure the hole is at a downward angle (min 5 degrees) so that the water will drain correctly.
Use a 180mm core drill to drill the two holes for the units ventillation,
ensuring that both the holes are aligned with the template.
Use the template to mark the position of the screws for the hanging rail,
using a spirit level to ensure it is straight and level.
Drill the marked holes using a suitable 8mm drill bit and insert wall plugs.
Line the hanging rail with the holes, and fix the rail into position using the
supplied screws.
Ensure that the hanging rail is securely fastened onto the wall, and that
there is no risk of the unit tipping or falling.
Roll the plastic vent sheets into a tube and feed them from the inside into the holes previously made. Ensure the tubes sit flush to the interior wall.
Go outside and trim off the excess vent tube using a sharp knife, keeping the edge as neat as possible.
Insert the indoor fixing ring from the vent cover onto the indoor side of the air vent. Then fold the external vent cover in half. Attach the chains to each side of the vent cover, before sliding the cover outside through the vent hole.
Expand the external cover, before tightly fixing the chains by hooking onto the indoor fixing ring. This will hold the external cover firmly in position. Repeat for the second vent.
Once the chains are fitted and secure, any excess chain should be removed by cutting the chain.
Lift the unit onto the wall, align the hanging holes with the hooks on the
hanging rail and gently rest the unit into place.
At the same time, slide the drain pipe through the drainage hole.
NOTE:
- please ensure that the backside of product is tightly attached on the wall to avoid additional vibration and noise.
- The end of the external water pipe must be placed in an open space or drain. Avoid damage or constriction to the drainage pipe to ensure the unit drains.
OPERATION
CONTROL PANEL
REMOTE CONTRODL
The air conditioner can be controlled with the remote control. Two AAA-
batteries are required.
NOTE : Further details of the functions can be found on the following
page.
FUNCTIONS
WIFI SETUP AND SMART FEATURES WIFI SETUP
BEFORE YoU START
- Ensure your router provides a standard 2.4ghz connection.
- If your router is dual band ensure that both networks have different network names (SSID). The provider of your router/ Internet service provider will be able to provide advice specific to your router.
- Place the air conditioner as close as possible to the router during setup.
- Once the app has been installed on your phone, turn off the data connection, and ensure your phone is connected to your router via WIFIL.
DOWNLOAD THE APP TO YOUR PHONE
Download the “SMART LIFE” app, from your chosen app store, using the QR codes below, or by searching for the app in your chosen store.
CONNECTION METHODS AVAILABLE FOR SETUP
- The air conditioner has two different setup modes, Quick Connection and AP connection (Access Point). The quick connection is a quick and simple way to set the unit up.
- The AP connection uses a direct local WIFI connection between your phone and the air conditioner to upload the network details.
- In Standby mode press and hold the speed button for 3 seconds (until you hear a bleep) to enter the wifi connection mode.
- Please ensure your device is in the correct wifi connection mode for the connection type you are attempting, the flashing of the wifi light on your air conditioner will indicate this.
CHANGING BETWEEN CONNECTION TYPES
To change the unit between the two wifi connection modes, hold the Speed button for 3 seconds.
REGISTER THE APP
SETTING UP YOUR HOME WITHIN THE APP
SMART LIFE is designed so it can work with a large number of compatible smart devices within your home. It can also be set up to work with multiple devices within different houses As such durin8 the setup process, the app requires that different areas are created and named to allow easy management of all your devices. When new devices are added, they are assigned to one of the rooms you have created.
CREATING ROOMS
CONNECTING USING QUICK CONNECTION
Before initiating the connection, make sure the unit is in standby mode, with the WIFI light flashing twice per second. If not follow the instructions for changing the connection mode. Also ensure your phone is connected to the wifi network. (We advise turning mobile data off during setup)
CONNECTING USING AP MODE (ALTERNATIVE METHOD)
Before initiating the connection, make sure the unit is in standby mode, with the wifi light flashing once per second. If not follow the instructions for changing the wifi connection mode. Also ensure your phone is connected to the wifi network. (We advise turning mobile data off during setup)
CONTROLLING YOUR DEVICE THROUGH THE APP
THE HOME SCREEN
Each device has its own entry on the home screen to allow the user to either quickly turn the unit on or off, or to enter the device screen to make other changes.
DEVICE SCREEN
The device screen is the main control screen for the air conditioner, providing access to the controls to amend the functions and settings.
Due to continuous development of the app, the layout and available features may be subject to change.
SMART SCENES
Smart Scenes is a powerful tool providing the option to customise the operation of the air conditioner based both on conditions within the room and outside influences. This gives the user the option of specifying much more intelligent actions. These are split into two catagories Scene and Automation.
SCENE
Scene allows for a one touch button to be added to the Home screen. The button can be used to change a number of settings in one go, and can change all the settings within the unit. A number of scenes can easily be setup, allowing the user to easily change between a number of preset configurations.
Below is an example of how to set up a scene:
AUTOMATION
Automation allows an automatic action to be set up for the device. This can be
triggered by the Time, indoor temperature, humidity of the room, weather
conditions, and a range of other influences.
ME
The profile tab gives you the option to edit both your detail, and use the
added features of the unit.
CHANGING THE NAME OF YOUR DEVICE
- When in any of the device screens further settings for the device can be accessed, by pressing on the three dots in the top right hand corner. The top option within this allows you to change the name of the device to something relevant to the use of the product, such as “Living Room Air Conditioner”.
- Within the menu, you also have the option of setting up a pattern lock or change your password.
DEVICE SHARING
This allows you to share access to the controls of your air conditioner with
friends and family.
In pageHome Management”, select My home”, you could “Add Member” there to share access to the controls of your air conditioner with friends and family, pls refer to the left picture.
INTEGRATION
This allows the unit to be integrated with your favourite home automation
hardware such as Google Home and the Amazon Echo.
Select More Services, you could integrate with third-party voice services, pls refer to the left picture.
TROUBLESHOOTING
Do not repair and may lead to failure, causing injuries and property damage. Only use it as directed in this user manual and only perform operations advised here. disassemble the air conditioning. Unqualified repair will invalidate the warranty
If problems not listed in the table occur or recommended solutions do not work, please contact the service centre.
ERROR CODES
Get In Touch
Call : 0845 6880112
Email : info@adremit.co.uk
Our Address
Puravent, Adremit Limited, Unit 5a, Commercial Yard, Settle, North Yorkshire,
BD24 9RH
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>