Shenzhen Deji Innovation Industrial DPA01 Pet Training Collar User Manual

PET TRAINING COLLAR
User Manual
Please read the quick start before beginning

DPAOl-1
Yersion:VOl

Thanks for choosing our products! Produkte entschieden haben!

Thanks for choosing our products!

This dog training collar is designed to make your dog’s life safe, happy, and harmonious with humans.

Warning Not for aggressive dogs
Aggressive dogs can cause serious injury or even death to their owners or others. If you are unsure if this product is suitable for your dog, consult your dog’s veterinarian or a
qualified dog trainer before using it.

Be careful when using the leash for training.
Pay attention to both you and your dog’s safety when learning and training on a leash. You should use a strong leash that is long enough for a dog to chase but not long enough to run into roads or other dangerous areas. Meanwhile, make sure you are strong enough to hold on to your dog during a chase.

Be careful of skin damage
Please read the instructions carefully use the product correctly according to the instructions and wear the dog’s collar correctly for your dog. Wearing a collar too long or too tight can cause the dog’s skin lesions which range from redness to compression ulcers, also known as bedsores.

• Dog Collar should not be worn for more than 12 hours per day.
• The position of the collar around the dog’s neck should be adjust­ ed as often as possible every l to 2 hours.
• Don’t connect the lead wire on the electronic collar in case of ca­ using too much electrostatic column pressure.
• Stop using the collar immediately until the skin recovers if a rash or ulcer occurs during the collar use.
• Please take your dog to a doctor immediately if the condition does not improve after 48 hours.
• Please keep the product away from your children as it is not a toy.
• This product is only suitable for training healthy dogs.

Brief introduction

Remote
A: Short press to increase the shock level
B: Short press to decrease the shock level
C: On/Off Button (long press to turn it off, short press to turn it on)
D: Ringtone Button
E: Vibration Button
F: Shock Button
G: Charging Port

Receiver Collar
H: The threaded hole of the electrostatic column
I: On/Off Button
(Short press to turn it on, long press to turn it off, long press for 5 seconds to enter pairing mode under power-off mode)
J: Charging Port (with cover)
K: LED indicator lights
(Green light flashing: the receiver is in wor­ king condition and with sufficient electricity; Red light flashing: the receiver is low battery and need to be charged)

Product Settings

Before using the dog training collar, the product sho­uld be set according to the following steps:

1. Charge the Remote and Receiver Collar.
2. Match the Remote and Receiver Collar (factory paired)
3. Prepare the Remote and press the “on” button to open it.
4. Prepare the Receiver Collar and press the “on” button to open it.
5. Functional test: Test the button function of the Remote and receiver before wearing the dog training collar.
6. The test lamp can be used to test the electronic shock function or as a wrench.

Charge the Remote and Receiver Collar

1. Plugin and charge the Remote and Receiver Collar for about 2 hours.
2. When fully charged, the LED indicator lights on the Receiver Collar will change from red to green. The power display on the Remote will stop circulating and show the full power grid.
3. The receiver should be covered with a rubber cover when the collar is fully charged.

Tips:

1. Overcharging will shorten the service life of the battery, so just charge it when the battery is low.
2. When the dog training collar is not in use, long-press the button to turn it off to extend the battery life.

Note:
Please use the Output: DC 5V 500- l 000mA charger to charge the product. Don’t use a charger that does not meet the specifications to charge the product.
Remote Settings
“On/Off” button of the Remote

1. Short press the ON/OFF button to turn the remote ON.
2. The LED screen will display the current mode, battery power, and shock level. If not, please charge the Remote.
3. Long press the ON/OFF button to turn the remote OFF.

As a Wrench
The Test Lamp can be used to tighten or loosen the electrostatic col­ umn when setting the Receiver Collar.

****Receiver Setting
Please use the distribution test tools to install the static column of the collar.

Please refer ta the picture to wear the collar on the dog’s neck.

You con adjust the collar length ii it is necessary.
Turn the Receiver Collar

• Press the On/Off button and the Green LED light comes on.

• In normal mode, the Green LED light will flash every 2 seconds, indicating the Receiver Collar is on and the battery is sufficient. If Red LED light flashes, indicating the battery is low.
  Turn off the Receiver Collar

• In working condition, long-press the On/Off button, and the red light flashes 3 limes and then goes out (about 3 seconds).
  Note: To extend the life of batteries, long-press the “ON/OFF” button to shut off the Receiver Collar when it is not in use.

Buttons of the Remote

| Ringtone: sends a tone with a non-adjustable level to the Receiver Collar.
---|---
| Vibration: sends a vibration with a non-adjustable level to the Receiver Collar.
| Shock: sends 1-16 adjustable levels of static stimulation to
the Receiver Collar.
| Short press to turn on, long press to turn off.
| Short press to increase the shock level.
| Short press to decrease the shock level.

Display Screen of the Remote

| Shock Level (can be adjusted when necessary)
---|---
| Remote battery display

Note:
The shock level con is adjusted from level l to level 16. Please,;, just it appropriately according to the dog’s response.
It is not recommended to press the “Vibration” or “Shock” button for too long a time to avoid causing physical or psychological damage to the dog.

Function Test

1. Hold the Remote approximately 2 feet away from the dog training collar and press the “Ringtone” button, and you will hear a beep so­ und.
2. Hold the Remote about 2 feet away from the dog training collar and press the “Vibration” button, and you will feel the vibration.
3. Press to decrease shock level to the lowest, starting from level l, press the “Shock” button, and increase shock level until the sensation begins to feel uncomfortable.
   NOTE: The duration of continuous stimulation transmission shall not exceed l Os. Ring, Shock, and Vibration function will stop working for Ss if it exceeds l Os. To reactivate, release and repress the button.

How to Use the Test Lamp
Shock Function Test

1. Turn on the Receiver Collar.
2. Press and hold the Test Lamp so that it is in close contact with the static column (or silicone cap) on the collar.

Press the “Shock” button and the lamp comes on. The intensity of the
Test Lamp increases as the shock level increases.
•
The pairing of Remote and Receiver Collar
l . When the Receiver Collar is in shutdown mode, long-press the “On/Off” button on the Receiver Collar for 5 seconds, the red and green LED indicator lights will blink for about lO seconds, indicating that it is ready for pairing.

2. Hold on the “Ringtone” and “Vibration” buttons for 3 seconds, the Green LED light on the Receivers Collar will flash five times, indicating suc­ successful pairing.
Dog Training
Selecting the Electrostatic Column Correctly
For a better training result, please select the appropriate size electr­ static column based on the gap between the Collar and the dog’s skin. If the dog’s hair is too long or thick,  please use a longer electrostatic column. If it’s not comfortable for your dog, you can install a silicone cap on the electrostatic column.

Collar Fitting
Please fit the collar properly on your dog. Make sure the static colu­ mn is close to the dog’s skin. When properly fitted, you should be able to put a finger in between the Receiver  Collar and the dog’s neck. Too loose: the Receiver Collar can be moved around the dog’s neck and the static column can hurt the dog’s skin.
Too tight : it may cause dogs to breathe hard.  Caution:

1. Do not shave all the hair around the dog’s neck, otherwise, it is more likely to increase the risk of the dog’s allergic skin pain.
2. The Collar should not be worn for more than 12 hours a day, or it may cause skin irritation and pain for the dog.

Find the Best Shock Level for Your Dog
The unit comes with Up and Down buttons to control the Shock Level.
Level l is the lowest shock level and level 16 is the highest. The best shock level for a dog depends on the dog’s temperament and the critical point for the shock. Be sure to increase the shock level step by step from the lowest level. If the dog begins to experience minor reactions such as flapping ears, licking lips, and tensing of the neck muscles, the current shock level is the most suitable for the dog. The shock level suited best to a dog can vary according to the training situation dog is distracted during training, which indicates that a higher level of Shock is required.

Device Information

Product Specification

The unit needs to be charged under any of the below situations:

1. The indicator light on the Receiver Collar flashes in red every 2 seconds or flashes rapidly and shuts off automatically.
2.  The 3 bar indicator on the Remote LED shows just l bar.
3. The indicator light on the Remote or Receiver Collar is not on.

Others:

Frequently Asked Questions

Is the Vibration/Shock safe for my dog?| The Vibration/Shock function is unpleasant but harmless. Electronic training device requires interaction between dogs and their owners to achieve the desired results.
How old does my dog have to be before using the Remote Training Collar?| Before using the training collar, the dog should be able to understand and perform simple commands, such as “Sit ‘ or ‘Stay’, and the dog should be at least 6 months old.
Once my dog is trained and has been obeying my comm- ones, will he have to continue to wear the Receiver Collar?| Probably not. But you may need to reinforce training with the Receiver Collar from time to time.
Is the Receiver Collar waterproof?| Yes.
Will I get exactly 984 feet of range with the Remote Training Collar?| The wireless connection range of the training collar will vary depending on the terrain, weather, vegetation, and transmission from other radio devices. See ‘How to Maximize your Wireless Range’ for tips on maximizing your range.
How long can I continuously deliver Vibration/Shock to my dog?| If you press RingtoneNibration/Shock button and deliver RingtoneNibration/Shock continuously to the dog for about 10 seconds. After this, there’s o time-out a Ringtone/ Vibration/Shock can not be delivered for 5 seconds. After the 5 seconds time-out period, Button can be pressed and Ringtone/ Vibration/Shock can be delivered again.

Troubleshooting Guide

What ii the dog doesn’t respond after pressing any of the buttons on the Remote?| • Make sure the Receiver Collar is on.
• Alter the first use of the Training Collar, the power of the Remote or Receiver Collar may be reduced ii the range is reduced.
• Different terrain, weather, vegetation, different signals em­ fitted by other radio devices and many other factors can
affect the wireless connection range of the device.
• Please test the Receiver Collar according to the instructions in the “How to Use the Test Lamp” section.
• Please increase shock level according to the instructions in the “Find the Best Shock Level for Your Dog” section.
• Please ensure that the static column on the Receiver Collar s close to the pet’s skin, as specified in” Collar Fitting”
section.
What if the Receiver Collar can’t be turned on?| • Please ensure that whether the Receiver Collar has been charged. It takes approximately 2 hours to fully charge.
What ii the Receiver Collar doesn’t respond to the Remote?| • Make sure the Receiver Collar is on.
• If the indicator light on the Receiver Collar does not go on after pressing any button on the remote, it should be determined whether the battery of the Remote and Receiver has power or not.
• If neither of the above solutions solves your problem, refer to “Pairing the Remote and Receiver Collar”.

Warranty and Repair Information

Two-year Limited Lifetime Warranty
The original buyer of the device is entitled to a 2-Year Warranty servi­ ces. The warranty begins from the date of purchase. For the first 2 years, coverage is for both Parts and  Labor on warranty repair servi­ ces.

After two years, replacement parts, maintenance labor, and other accessories are not covered by the warranty. The customer shall bear the resulting freight, replacement cost of spare parts beyond the two-year warranty period, and related maintenance labor costs. The cost of maintenance labor varies with the degree of maintenance. The limited lifetime warranty will expire five years after the product is discontinued from production.
To qualify for the Warranty
All products must be provided with the purchase certificate to enjoy the warranty service within the warranty period. We strongly recom­ mend keeping the original receipt. If proof of purchase is not ava­ available at the time of service, we will estimate the age of the unit by the serial number. Serial number estimates can differ from the actual p­ purchase date.  A serial number estimate is the only method of deter­ mining an approximate date of purchase without proof of purcha­
se.

Conditions Nat Covered Under Warranty
We DO NOT offer a warranty for products that have been bought se­ secondhand or as a resold product. We DO NOT replace defective units or provide refunds for products purchased from us after 30 days from the date of purchase. Issues of replacement and refunds on units purchased less than 30 days from an authorized dealer must be addressed to the dealer directly. If the products purchased from an authorized dealer are after 30 days from the date of purchase, please send the units to us for service and repair. We DO NOT cover the cost of repairs and replacements due to misuse by the owner or the dog, improper maintenance, and/or lost units. Any water damage on the Water Resistant remote and the Water Resistant Receiver of our product series will not be covered. All replacement costs for either the remote or receiver will be the owner’s responsibility. The warranty is void if the unit has been altered or an unauthorized per­ son has damaged the unit while attempting repair work. We reserve the right to retain and discard any parts or accessories that have b­ been found damaged upon replacement and repair.

Procedure for Repair Work
If the unit is malfunctioning, please refer to the “Troubleshooting Guide” in the quick start before sending it back for Service. The cost of shipping products under warranty back is the customer respon­ sibility. We are not responsible for units damaged or lost in transition. We are not responsible for loss of training time or inconvenience while the unit is in for repair work. We do not provide loaner units or any form of compensation during the repair period. A copy of the sales receipt showing the purchase date may be required before warranty work is initiated. Please include a brief explanation outlin­ ing the problem and include your name, address, city/state/zip code, daytime phone number, evening phone number, and email address.

Compliance
FCC – USA
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined y turning the equipment off and on, the user is  encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>