Kingwo NT07E Asset GPS Tracker User Manual

Kingwo NT07E Asset GPS Tracker User Manual

NT07E

Shenzhen Kingwo loT Co., Ltd.
www.365qczx.net
www.kingwoiot.com
＋86 0755 86704262
marketing＠kingwoiot.com

Declaration
The contents of this manual might be updated from time to time without prior notice; the updated content will be added to the new version of this manual. Kingwo reserve the rights to update the products or procedures described in the manual at any time. If there is a description of the product in the manual that does not match the actual product, the actual product shall prevail. Kingwo owns the final interpretation rights of this manual.

PART 1: Product Overview

1.1 Appearance

1.2 LED status

1.3 Product features summary

• Built in 8100mah batteries, it can last 5 years if upload data once a day
• Track: To check the assets location once a day or several times a day, interval is configurable
• Alarms: Motion alarm, removal alarm
• Multiple position modes: GPS, WIFI, LBS, AGPS
• Temperature monitor
• Battery level upload
• Weatherproof for outdoors assets monitor
• No wires and magnets for easy installation
• Jamming detection

1.4 Hardware parameters

PART 2: Product Functions

2.1 Work modes
The default upload interval is one-day one ping, the data packets information includes GPS status, longitude and latitude, cellular signal Strength, satellite numbers, battery level etc, there are multiple track modes available from the device, below is the explanation for work mode priorities:

• Track mode>Warehouse >Timely upload=Clock mode=Week mode= Motion and static mode；
• The work mode which is equal can be replaced by each other, as the last configuration will
  prevail

2.1.1 Track mode

Note:
Under track mode, GPS position is on priority, and acquire LBS and WIFI data each 30 seconds
Device enters into power save mode if the device is in static status in 5 minutes, GPS is switched
off, but it will keep communication with backend and upload data according to the preconfigured intervals

Under track mode, if the SIM card is loosen, or network register failure or server failure, device will switch off communication and position 30 minutes , however if the removal alarm triggered, it will resume to normal mode GPS will wake up if vibration happens

2.1.2 Warehouse mode

2.1.3 Fixed upload mode (Recommended)

2.1.4 Clock mode

2.1.5 Week mode

2.1.6 Motion and static mode

Note:
Device can’t be wake up by vibration while in motion mode
Device can be wake up by vibration while in static mode
After wake up, there should be 3 seconds vibration in 6 seconds, device will turn on cellular
module and upload position data, otherwise it would enter into sleep mode again and maintain
the previous configuration parameters

2.2 AGPS

When the device successfully registers on network, AGPS is available to speed up the position speed and improve the position accuracy

2.3 LBS

If device enters into the blind zone and GPS cannot be fixed, the device will switch to LBS position, LBS provides the reference location which might not be accurate

2.4 Wi-Fi
The device has built in Wi-Fi Chip, it automatically connects to the WIFI hotspot nearby and filter the hotspot info then select the WIFI hotspots with strongest signal, the device will pack those hotspots info and saved into the packet that will be uploaded, after the backend receives Wi-Fi information, it will interpret the WIFI info and acquire the current location from the Wi-Fi database, The default setting is WIFI priority, once it detects WIFI Hotspot, it will upload WIFI info only , and do not use GPS, if WIFI is not detected, it will use GPS to position.

Kindly reminder: To use Wi-Fi feature, please make sure your software supports Wi-Fi database

2.5 Blind data storage
When the device enter into blind zone when in sleep mode, it will store the trace data according to the preconfigured time interval and it will upload the data in the blind zone to the backend when the cellular network recovers

2.6 Temperature detection
The device built-in temperature sensor, it detects the temperature once the device is turned on, then will read it every 16 seconds. The temperature accuracy 95%.

2.7 OTA commands from backend
Since the wake up of the device is normally short before enter into sleep mode, it is hardly to receive SMS , to ensure the command sending efficiently, we suggest an OTA commands to be sent from the platform, when the device is online, the backend will automatic send this command, to make sure the commands is properly received.

2.8 Strong Magnetic and waterproof function
NT06EC is with built-in with super strong magnet that can firmly stick the device to the metal surface, it is easy to install and conceal, and the device is with waterproof function, which can be installed on any assets that are outdoors

2.9 Tamper alarm
There is a high sensitive light sensor at the bottom, if the device is tampered, either the device is
working or in sleep mode, it will be activated and enter into anti-removal status and switch on
anti-removal alarm, and report the alarm info to the backend or preset phone number.

PART 3: NT06E Setup

3.1 Setup and debugging

3.1.1 SIM card installation
Unscrew the top cover of the device, insert the prepared SIM card into the SIM card holder, and then confirm that the SIM card button is well placed . Please make sure that the SIM card has data service available in advance and write down the SIM card number.

3.1.2 Main unit power on
After installing the SIM card, turn the battery switch to the ON position. When the red light starts to blink, indicating that the device is powered on.

3.1.3 Major parameter setting by SMS or SSCOM tool

SMS list:

SSCOM configuration:
Please contact Kingwo team for configuration tools and documents.

Mounting recommendations

• The bottom of the tracker is fitted with a powerful magnet, you can put the tracker directly on a magnetic surface.
• Please do not put tracker in the metal environment which will affect the GPS signal.

Safety Information

• Don’t dissemble the device by yourself
• Avoid strong humidity, direct sunlight, and high temperature
• Don’t use on airplane

Shenzhen Kingwo IoT Co.,Ltd.
Address: 7th Floor, Block A, R&D Building, Tsinghua Information Hi-Tech
Port, Nanshan District, Shenzhen, Guangdong, China
Tel： 86-755-86704262
Fax： 86-755-86671531-8000
Website：www.kingwoiot.com www.365qczx.net
Email：marketing@kingwoiot.com

FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TVtechnician for help.
• To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>