ProofVision PV10-PS Oral-B In-Wall Electric Toothbrush Charger Instruction Manual
- June 4, 2024
- ProofVision
Table of Contents
ProofVision PV10-PS Oral-B In-Wall Electric Toothbrush Charger
Installation
This product is IP44 rated and is suitable for use in bathrooms with Oral B/Braun rechargeable toothbrushes only. Operate the Toothbrush Charger on a 220V – 240V supply only.
SAFETY INSTRUCTIONS
All installation work should be undertaken by a competent person in accordance
with the current edition of the IEE Wiring Regulations (BS 7671) and
appropriate statutory regulations. In the Republic of Ireland the installation
must be in accordance with the ETCI National Rules for Electrical
Installations -ET101.
IF IN DOUBT, CONSULT A QUALIFIED ELECTRICIAN
Before starting any electrical work, ensure that the electricity supply is
SWITCHED OFF at the mains. For additional safety, remove the fuse or switch
off the circuit breaker at the fuse box or consumer unit.
IMPORTANT NOTICE
WIRING COLOUR CHANGES
As from 1st April 2004 new installations in the UK could be wired using the
new EU Harmonised colours for the supply conductors of twin and earth cable:
New Colours
Brown = Live
Blue = Neutral
Old Colours
Red = Live
Black = Neutral
The old colours will cease to be used from 1st April 2006.
Flexible cable colours remain unchanged:
Brown = Live
Blue = Neutral
Eire conductor colours for twin and earth cable and flexible cable:
Brown = Live
Blue = Neutral
INSTALLATION AND WIRING INSTRUCTIONS
This toothbrush charger unit is suitable for mounting with a 47mm deep 2 gang
flush metal box. The depth of the recess required for installation of the
Toothbrush Charger is 47mm.
Please note – check orientation of box when fitting this unit on a
surface pattress box.
For the best mounting results and visual appearance, it is recommended that
prior to installation, the mounting surface between the accessory front plate
is first prepared to ensure that it is flat and all high spots have been
removed.
- Remove product and screws supplied from the packaging
- Feed incoming supply cable through appropriate knockout entry in back box. Ensure a protective cable grommet is fitted when using a flush metal box.
- Remove suitable length of outer sheath from the supply cable. Remove 10mm from the live and neutral inner insulation to expose the conductor ends.
- Insert Neutral conductor into the charger supply unit terminal into either of the 2 available terminals available (mains are both red so are interchangeable)
- Insert Live conductor into the charger supply unit terminal into either of the 2 available terminals available (mains are bath red so are interchangeable)
- Before connecting the protective earth conductor, ensure that all bare earth conductors are sleeved with a length of Green/ Yellow sleeving (not supplied)
- Insert sleeved earth conductor into terminal marked with the Earth symbol.
- Ensure that an additional sleeved earth conductor is also fitted between the charger unit earth terminal and the earth terminal fitted in the flush metal box.
- Ensure all terminal screws are tight.
- Fit the toothbrush charging unit onto the mounting box, taking care not to trap any cables.
- Secure unit using the fixing screws.
- Ensure that the plastic frame is correctly fitted and then fit the front plate in place.
- Refit the supply fuse (if removed) and switch on mains supply.
- The Toothbrush Charger energy output is 0.6 – 0.8W with no rechargeable toothbrush charging on the unit. The Toothbrush Charger energy output is 1.0 – 1.3W with a rechargeable toothbrush charging on the unit.
- Operate the Toothbrush Charger on a 220V – 240V supply only.
DISPOSAL OF THE TOOTHBRUSH CHARGER
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems). This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.
Contact Us
- +44 (0) 203 4111 693
- sales@proofvision.co.uk
- www.proofvision.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>