contour RM-PRO-WL RollerMouse Pro Wireless User Guide

contour RM-PRO-WL RollerMouse Pro Wireless

What’s in the Box?

1. RollerMouse Pro Wireless
2. Wrist rest (if included)
3. Two Keyboarcd risers
4. Dongle
5. USB extender
6. USB charging cable

• Attached together in the box.

Functions

• A. Cursor speed
• B. Power switch
• C. Rollerbar
• D. Copy
• E. Paste
• F. Left-click
• G. Right-click
• H. Scroll wheel
• I. one Touch” double-click

Quick Start

1. To connect via Bluetooth:
   Power on RollerMouse (button B). On your computer. navigate to the area of settings regarding Bluetooth connections. Select the option to add or discover a Bluetooth device. Your RollerMouse will automatically be recognized, select it for the computer to start a Bluetooth connection.

2. To connect via USB dongle:
   Insert the USB dongle into the available USB port and power on your RollerMouse. Your computer will recognize your new device and connect automatically.

3. To connect via a wired USB connection:
   Connect the USB cable to your RollerMouse and into an available USB port on your computer. Your computer will recognize your new device and connect automatically.

Cursor Speed (DPI)

Press the Cursor speed button A to cycle through cursor speeds. There are speed selections that range from slow (600 DPI) to fast (2800 DPI). Speed can be identified by the LED lights as shown. Hold Cursor speed button A for 8 seconds to default settings.

Battery

• Battery level is shown when the device is powered on or plugged in.
• If battery is below 20%, a single light will blink to indicate the need to charge the device.

Click force adjustment

Click force refers to the level of resistance when clicking the Rollerbar. To adjust click force, press and hold button A ( Cursor speed button),then press and release button C (Rollerbar). Move button H (scroll wheel) up and down to adjust the click force settings. The current click force level will be displayed by the LEDs on the right side of the unit.

Note: The Rollerbar click function can be turned off using the above adjustment method, by moving the scroll wheel until all LEDs are lit.

Click volume adjustment

The Rollerbar has 6 different click volume settings. To change the click volume, press and hold button A (cursor speed), while continuing to hold A, press and release button H (Scroll wheel), the LED light will show the current click volume setting. Move button H up/down to adjust volume setting. Release button A to confirm adjusted click volume.

Note: The Rollerbar click volume can be turned off using the above adjustment method, by moving the scroll wheel until all LEDs are lit.

Pairing and Secondary Options

1. Restart Bluetooth pairing:
   Press button A. While continuing to hold A, press and release button F two times, then release button A.

2. Select Bluetooth-only connectivity:
   Press button A. While continuing to hold A. press and release button F three times ,then release button A.

3. Select dongle-only connectivity:
   Press button A.while continuing to hold A. press and release button G three times ,then release button A.

4. Restore pairing with dongle:
   Unplug then re-plug the dongle to the unit to enable pairing.Hold the device close to dongle and press button A. While continuing to hold A, press and release button G two times, then release button A.

5. Reset wireless function to automatic pairing mode:
   Press button A. While continuing to hold A, Press and release button F, then release button A.

   • When the device is plugged in through the USB cable, this connection overrides wireless connectivity.
   • Please visit contourdesign.com/BT for further information regarding your Bluetooth connection.
   • If Bluetooth- or dongle-only connectivity is activated, the RollerMouse will retain connection when the device is powered off then powered back on again.

Charging/ Extension Wireless Connection

To charge your RollerMouse remove the USB extender and dongle from the charging cable. Plug the USB-C end into the RollerMouse. Your RollerMouse will charge in 5 hours. You may continue to use your RollerMouse as it charges. Once powered on, the device is in automatic mode which will pair to the first available connection. The device will attempt to connect to the dongle first. If no connection is made, the device will attempt to connect via Bluetooth using the pairing information that is already in the unit. If no pairing information is available, it will start Bluetooth pairing mode and remain in that pairing mode for about two minutes. If device is left in automatic pairing mode, RollerMouse will cycle through the above steps each time it’s powered off and then powered back on again.

Battery Disposal

Keyboard Risers

Before using your RollerMouse Pro, take a moment and adjust the keyboard risers to achieve the desired keyboard height and angle. For a proper ergonomic position, the front edge of the keyboard should be as close to the Rollerbar as possible.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IC Statement

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The term “IC: “ before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications.

2-year Warranty

• All Contour Design products come with a 2-year Warranty.

Product Support

• For information on software drivers, product manuals ,and advanced product settings such as thin client mode, please visit contourdesign.com/support

Sales Support

If you have questions about your recent purchase, email us

• United States: ergoinfo@)contourdesign.comcontourdesign.com)
• All other countries: [email protected]

www.contourdesign.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>