Contour Design CDRMRED10110 RollerMouse Red Wireless Ergonomic Mouse User Guide
- June 1, 2024
- contour design
Table of Contents
Contour Design CDRMRED10110 RollerMouse Red Wireless Ergonomic Mouse
What’s in the Box?
- RollerMouse Red Wireless
- Wrist rest
- Two short keyboard risers
- Two long keyboard risers
- Wrist rest removal key
- Dongle
- USB extender
- USB charging cable
Please find accessories # 6,7,8 attached in the box
Functions
- A. Rollerbar
- B. Cursor speed and battery level indicator LED
- C. Copy
- D. Paste
- E. Left-click
- F. Right-click
- G. Scroll wheel
- H. ·one Touch” double-click
- I. On-off Switch
- J. Dongle storage compartment
Quick Start
To connect via Bluetooth:
Power on RollerMouse (button 1). On your computer, navigate to the area of
settings regarding Bluetooth connections. Select the option to add or discover
a Bluetooth device. Your RollerMouse will automatically be recognized, select
it for the computer to start a Bluetooth connection.
To connect via USB dongle:
Insert USB dongle into the available USB port and power on your RollerMouse.
Your computer will recognize your new device and connect automatically.
To connect via a wired USB connection:
Connect USB cable to your RollerMouse and into an available USB port on your
computer. Your computer will recognize your new device and connect
automatically.
Cursor Speed (DPI)
Press the Cursor speed (button B) to cycle through cursor speeds. There are
speed selections that range from slow (600 DPI) to fast (2800 DP)). Speed can
be identified by the LED lights as shown. Hold Cursor speed (button B) for 8
seconds to default settings.
Battery
Battery level is shown when the device is powered on or plugged in. If
battery is below 20%, a single light will blink to indicate the need to charge
the device.
Pairing and secondary options
- Restart Bluetooth pairing : Press button B. While continuing to hold B, press and release button E two times, then release button B.
- Select Bluetooth-only connectivity: Press button B. While continuing to hold B, press and release button E three times, then release button B.
- Select dongle-only connectivity: Press button B, while continuing to hold B, press and release button F three times, then release button B.
- Restore pairing with dongle : Unplug then re-plug the dongle to the unit to enable pairing. Hold the device close to dongle and press button B. While continuing to hold B, press and release button F two times, then release button B.
- Reset wireless function to automatic pairing mode : Press button B, While continuing to hold B, press and release button E, then release button B. When the device is plugged with the USB cable, this connection overrides wireless connectivity. Please visit contourdesign.com/BT for further information about Bluetooth.
Charging/Extension
To charge your RollerMouse remove the USB extender and dongle from the
charging cable. Plug the USB-C end into the RollerMouse and connect to a USB-A
at your computer. Your RollerMouse will be fully charged in approx. 5 hours.
You may continue to use the RollerMouse as it charges. Once powered on, the
device is in automatic mode which will pair to the first available connection.
The device will attempt to connect to the dongle first. If no connection is
made, the device will attempt to connect via Bluetooth using the pairing
information that is already in the unit. If no pairing information is
available, it will start Bluetooth pairing mode and remain in that pairing
mode for about 3 minutes. If the device is left in automatic pairing mode, the
RollerMouse will cycle through the above steps each time it’s powered off and
then powered back on again.
Rollerbar click force adjustment
Click force refers to the level of resistance when clicking the Rollerbar.
To adjust click force, press and hold button B (cursor speed) then press and
release button A (Rollerbar). Move button G (Scroll wheel) up and down to
adjust the click force settings. To disable the Rollerbar click function,
adjust the click tension until all LEDs are illuminated.
Rollerbar click volume adjustment
The Rollerbar has 6 different click volume settings. To change the click
volume, press and hold button B (Cursor speed), while continuing to hold B
(Cursor speed), press and release button G (scroll wheel), the LED light will
show current click volume setting. Move button G (scroll wheel) up/down to
adjust volume setting. Release button B to confirm adjusted click volume. To
disable the Rollerbar click volume, adjust the click volume until alle LEDs
are illuminated.
Keyboard Risers
Before using your RollerMouse, take a moment and adjust the keyboard risers to
achieve the desired keyboard height and angle. For a proper ergonomic
position, the front edge of the keyboard should be as close to the Rollerbar
as possible.
Software driver
All Contour’s ergonomic products are plug-and-play. If you want to customize your RollerMouse, we recommend downloading the free driver available at: https://contourdesign.com/drivers
Battery disposal
2 year guarantee
All Contour Design products come with a 2 year guarantee.
Product Support
For information on software drivers, product manuals, and advanced product
settings such as thin client mode, please visit
contourdesign.com/support
Sales Support
If you have questions about your recent purchase, email us:
- United States :[email protected]
- All other countries: [email protected]
MIX Paper from responsible sources FSC® C137900