Contour Desgn CDUMBK11001 Wireless Right Unimouse Instruction Manual

June 1, 2024
Contour Desgn

Contour Desgn CDUMBK11001 Wireless Right Unimouse

Contour-Desgn-CDUMBK11001-Wireless-Right-Unimouse-
product

www.contourdesign.com

Functions

Contour-Desgn-CDUMBK11001-Wireless-Right-Unimouse-
fig-1

Quick Start

  1. To connect via Bluetooth:
    Power on Unimouse. On your computer, navigate to the area of settings regarding Bluetooth connections. Select the option to add or discover a Bluetooth device. Your Unimouse will automatically be recognized, select it for the computer to start Bluetooth connection.

  2. To connect via USB dongle:
    Insert USB dongle into available USB port and power on your Unimouse. Your computer will recognize your new device and connect automatically.

  3. To connect via a wired USB connection:
    Connect USB cable to your Unimouse and into an available USB port on your computer. Your computer will recognize your new device and connect automatically.

Contour-Desgn-CDUMBK11001-Wireless-Right-Unimouse-
fig-2

Cursor Speeds (DPI)

Press the Cursor speed (button A) to cycle through cursor speeds. There are speed selections which range from slow (800 DPI) to fast (4000 DPI). Speed can be identified by the LED lights as shown. Hold Cursor speed (button A) for 8 seconds to default settings.

Contour-Desgn-CDUMBK11001-Wireless-Right-Unimouse-
fig-4

Battery

Battery level is shown when the device is powered on or plugged in. If battery is below 20%, a single light will blink to indicate the need to charge the device.

Contour-Desgn-CDUMBK11001-Wireless-Right-Unimouse-
fig-4

Pairing and secondary options

  1. Restart Bluetooth pairing:
    Press button A. While continuing to hold A, press and release button F two times, then release button A.

  2. Select Bluetooth-only connectivity:
    Press button A. While continuing to hold A, press and release button F three times, then release button A.

  3. Select dongle-only connectivity:
    Press button A, while continuing to hold A, press and release button G three times, then release button A.

  4. Restore pairing with dongle:
    Unplug then re-plug the dongle to the unit to enable pairing. Hold the device close to dongle and press button A While continuing to hold A, press and release button G two times, then release button A.

  5. Reset wireless function to automatic pairing mode:
    Press button A. While continuing to hold A, press and release button F, then release button A.

Charging/Extension

To charge your Unimouse remove the USB extender and dongle from the charging cable. Plug the USB-C end into the Unimouse and connect to a USB-C at your computer. Your Unimouse will be fully charged in approx. 2 hours.You may continue to use the Unimouse as it charges.
Once powered on, the device is in automatic mode which will pair to the first available connection. The device will attempt to connect to the dongle first If no connection is made, the device will attempt to connect via Bluetooth using the pairing information that is already in the unit. If no pairing information is available, it will start Bluetooth pairing mode and remain in that pairing mode for about 3 minutes. If the device is left in automatic pairing mode, the Unimouse will cycle through the above steps each time it’s powered off and then powered back on again.

Contour-Desgn-CDUMBK11001-Wireless-Right-Unimouse-
fig-8

Adjustments

Contour-Desgn-CDUMBK11001-Wireless-Right-Unimouse-
fig-9

Vary Your Posture

Adjustability is the most important feature of the Unimouse. We encourage you to explore a variety of positions while using your Unimouse. Unimouse has 4 points of articulation that are friction-based to provide stability in any position. Dorit be afraid to experiment! The articulating hindge will reach its maximum vertical tilt at 70 degrees. and the Articulating Thumb Support (ATS)will not extend past its maximum length ofl4 mm.

Body Tilt Adjustment

Adjust body tilt for your desired mousing angle. The friction based adjustment allows vertical positions from 35° to 70° and every angle in between.

Contour-Desgn-CDUMBK11001-Wireless-Right-Unimouse-
fig-10

Thumb Support Width Adjustment

The thumb rest con be extended or collapsed to accommodate different hand sizes. For smaller hands, collapse the thumb rest.
For larger hands, pull the thumb rest outward to extend it. The thumb support width adjustment allows you to vary the position of your thumb to relax your hand while you mouse.

Contour-Desgn-CDUMBK11001-Wireless-Right-Unimouse-
fig-11

Thumb Support Slide

Slide the thumb support forward or back to accommodate variations in thumb length and grip preference.

Thumb Support Rotation

The thumb support can be rotated in any direction to adjust to your prefered thumb support position.

Press and hold cursor speed button. While holding the cursor speed button press the middle click button in succession until the desired selection is reached. Please see the legend below for a list of available middle click button options.

Contour-Desgn-CDUMBK11001-Wireless-Right-Unimouse-
fig-14

Software driver

All Contour’s ergonomic products are plug-and-play. If you want to customize your Unimouse, we recommend to download the free driver available at: https://contourdesign.com/drivers

Battery disposal

Contour-Desgn-CDUMBK11001-Wireless-Right-Unimouse-
fig-15

  • 2 year guarantee
    All Contour Design products come with a 2 year guarantee.

  • Product Support
    For information on software drivers, product manuals. and advanced product settings such as thin client mode, please visit: contourdesign.com/support

  • Sales Support
    If you have questions about your recent purchase, email us:
    United States:ergoinfo@lcontourdesign.com
    All other countries: support@lcontourdesign.com

MIX
Paper from responsible sources
FSC® C137900

FSC

www.fsc.org

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals