Zhejiang Tri Mix Technology TRIMIX-RF10A Remote Controller User Manual
- June 6, 2024
- Zhejiang Tri Mix Technology
Table of Contents
Zhejiang Tri Mix Technology TRIMIX-RF10A Remote Controller
ELECTRONICS OVERVIEW
PAIRING THE WIRELESS REMOTE
STEP 1：
Push in on bottom of remote to release battery cartridge and install three AAA
batteries into the remote battery compartment.Push in firmly to close.
STEP 2：
Plug the base into a power source and press the Pairing Button/Program
Button on the control box approximately in 1s,ensure the Pairing Lamp – White
(Third) flashing.
STEP 3:
-
Press “SW” until the backlight LED flashing, release it and then press “HEAD UP”, never release until the backlight LED is lighting all long, the remote is pairing and release it.
-
When the Pairing Button/Program Button on the control box and the backlight LED on the remote stop flashing, and the buzzer on the control box has a “DI” sound, pairing is completed.
-
If the function on the remote can not be operated, repeat the pairing again.
FUNCTIONAL OPERATING FOR WIRELESS REMOTE
MARK
|
STEP1
|
STEP2
|
FUNCTION
|
DESCRIPTIONS
---|---|---|---|---
|
Press “SW” in 3s until the backlight LED flashing and then press the “BUTTON” in STEP 2
|
TV
|
MEMORY POSITION
| The backlight LEDs all OFF before operating.
l Press（TV,ZG）until the backlight LED is lighting and the memory position is completed.
l When the backlight LED is lighting and press again, clear the corresponding memory position.
l TV & ZG have the memory position.
ZG
ANTISNORE| New ANTI-SNORE preset position and five minutes will be reset.
HEAD DOWN|
FUNCTIONS IN CIRCLING
| Head up and down functions in circling.
BACK DOWN| All bed base functions up and down in circling.
FOOT DOWN| Foot up and down functions in circling.
HIP DOWN| Hip up and down functions in circling.
FOOT UP| SHORTCUT
KEY
| Foot down tilt ( Music position).
HIP UP| Head down tilt ( Leg relaxing position).
HEAD UP| PAIRING| Pairing the remote and control box.
FLAT
| FORCED
RESET
|
The bed will be in FLAT position when the bed is breakdown.
FUNCTIONAL OPERATING FOR WIRELESS REMOTE
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment .
This transmitter must not be collocated or operating in conjunction with any
other antenna or transmitter.
For Control Box device: This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.