ORing IGAP-610H+ Industrial Wireless LAN Access Point Installation Guide

: June 6, 2024
: ORing

Table of Contents

Introduction
Features
Package Contents
Preparation
Installation
Configurations
Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Wireless
ACCESS POINT
I N D U S T R IAL
Quick Installation Guide
IGAP-610H+
Industrial Wireless LAN Access Point

Introduction

IGAP-610H+ is a reliable WLAN Access Point with 1 Ethernet Gigabit port and IEEE 802.11 a/b/g/n wireless module. It can be configured to operate in AP/Client/Repeater Mode. You are able to configure IGAP-610H+ by WEB interface via LAN port or WLAN interface. In addition, IGAP-610H+ also provides P.D. feature and the Ethernet port which is fully compliant with IEEE802.3af PoE P.D. specification. Therefore, IGAP-610H+ is one of the best communication solutions for wireless applications on the industrial network.

Features

High-Speed Air Connectivity: Dual Band in IEEE 802.11 a/b/g/n and b/g/n WLAN interface selectable and support up to 300Mbps link speed
12-48VDC power input on the terminal block
1 Gigabit Ethernet ports with 2KV isolation for PoE P.D.
Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK (TKIP, AES)/802.1X Authentication supported
Support X-Roaming < 100 ms
Support Multiple-SSID to 4 SSID with VLAN
Support MAC Filter
High transmission power (27 dBm Max.)
High data throughput with HT40 2×2 MIMO
Support Long Distance Air Connectivity
Support AP/Client/Repeater
Wireless connecting status monitoring
Secured Management by HTTPS
Event Warning by Syslog, Email, SNMP Trap, and Relay output
Rigid IP-30 housing design
DIN-Rail and Wall-mount enabled

Package Contents

The device is shipped with the following items. If any of these items are missing or damaged, please contact your customer service representative for assistance.

Contents	Pictures	Number
IGAP-010H+		X 1
GIG		X 1
DIN-rail kit		X 1
Wall-Mount Kit		X 2
4-pin terminal block		X 1
Power cable with power jack		X 1
CD		X1

Preparation

Before installation, make sure you have all of the package contents available and a PC with Microsoft Internet Explorer 6.0 or later, for using web-based system management tools.

Safety & Warnings
Elevated Operating Ambient: If installed in a closed environment, make sure the operating ambient temperature is compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of airflow required for the safe operation of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
Dimension Unit =mm (Tolerance ±0.5mm)
Panel Layouts

Power LED
System LED
PoE power status
WLAN Antenna
LED for wireless signal strength
LNK/ACT LED for Giga PoE LAN port
Giga PoE LAN port
Speed LED for Giga PoE LAN port
Terminal block
Reset button
Grounding screw
Din-rail screw holes
Wall-mount screw holes

Installation

DIN-rail
Step 1: Slant the device and screw the Din-rail kit onto the back of the device, right in the middle of the back panel.
Step 2: Slide the device onto a DIN-rail from the Din-rail kit and make sure the device clicks into the rail firmly.
Wall-mount
Step 1: Screw the two pieces of wall-mount kits to the top and bottom panels of the device. A total of eight screws are required, as shown below.
Step 2: Use the device, with wall mount plates attached. as a guide to mark the correct locations of the four screws.
Step 3: Insert a screw head through the middle of the keyhole-shaped aperture on the plate. and then slide the device downwards. Tighten the screw head for added stability.
Wiring
Power inputs
The device supports dual redundant power supplies, Power Supply (PWR1) and Power Supply 2 (PWR2). The connections for PWR1, PWR2 are located on the terminal block.
STEP 1: Insert the negative/positive wires into the V-/V+ terminals, respectively.
STEP 2: To keep the DC wires from pulling loose, use a small flat-blade screwdriver to tighten the wire-clamp screws on the front of the terminal block connector.
Network Connection
The device has three standard Ethernet ports. According to the link type, the device uses CAT 3,4,5,5e UTP cables to connect to any other network devices (PCs, servers, switches, routers, or hubs). Please refer to the following table for cable specifications.
Cable Types and Specifications:

Cable	Type	Max. Length	Connector
10BASE-T	Cat. 3, 4, 5100-ohm	UTP 100 m (328 ft)	R1-45
100BASE-TX	Cat. 5 100-ohm UTP	UTP 100 m (328 ft)	R1-45
1000BASE-T	Cat. 5/Cat. 5e 100-ohm UTP	UTP 100 m (3281t)	R1-45

RJ-45 Pin Assignment

10/100 Base-T(X) RJ-45 port

Pin Number| Assignment
1| TD+
2| TD-
3| RD+
4| Not used
5| Not used
6| R D-
7| Not used
8| Not used
1000Base-T RJ-45 port

Note:“+” and“-” signs represent the polarity of the wires that make up each wire pair.

Configurations

After installing the device and connecting cables, the green power LED should turn on. Please refer to the following tablet for LED indication.

LED	Color	Status	Description
P.O.E	Green	On	PoE power on
P1/ P2	Green	On	DC power 1/2 is activated.
SYS	Green	On	System is ready
Blinking	System is booting up
WLAN	Green	On	WLAN activated
Blinking	Transmitting wireless data
WLAN Strength	Green	On	LLAN signal strength.

1<25%, 2<50%, 3<75%, 4<100%

Follow the steps to set up the card:

Launch the Internet Explorer and type in the IP address of the switch. The default static IP address is 192.168.10.2
Log in with default user name and password (both are admin).
After logging in, you should see the following screen. For more information on configurations, please refer to the user manual.

Resetting
To restore the device configurations back to the factory defaults, press the Reset button for a few seconds. Once the power indicator starts to flash, release the button. The device will then reboot and return to factory defaults.

Specifications

ORing W LAN Accts.; Point Model

Physical Port.

10 /100/10000ase-T(X) Ports In Auto MOUNDIX

| IGAP-610H+

1

---|---
Antenna Connector| 2
Po! P.D Port

WIAN Feature Antenna Connector

| Present at ETH1

Fu I y compliant with IEEE 802.341 Power Devi:e specification
Over lead * Siert OrCult protection Isolation Voltage: 2000VOCmin. Isolation Resistance: 10′ ohms min Reverse SMA Female

Operating 140de| AP/Client/Repeater
Modulation| IEEE802.11a: (WOM IEEE802.11b: COODQPSK/DBPSK
IEEE8 02.11g: OF014
IEEE802.11n: BPSK, QPSK, 16-QA1, 64-QAM
Frequency Bend| America / FCC: 2.412.2.462 G Hz (11 channels)
5 .180.5.240 G Hz & 5.745.5.825 Gus ( 9 channels ) Europe CE / ETSI : 2.412.2.472 GHZ ( 13 channels)
5.1805.240 Gift (4 channels)
Transmission Rate| 802.11b: 11, 5.5, 2, 1 Mbps
802.119: 54, 48, 36, 24, 18, 12, 9, 61Cms 802.11n: up to 300140PS
Transnet Power| 802.11a: 23dBm 1.5dBm(P6M)ps, 21dBm 1.5dBm(P54M)ps 802.110: 23dBrn • 1.5013m0 IMO pi, 23d5m • 1.5011m41111140 DS 802.11g: 23d1m • 1.5df5m060113ps, 21dBm • 1.5dErn054Mbps 802.11gn HT20: 20dBm • 1.506nstplea7, 802.1 ign HT40: 2008m ± 1.500ngiNGS7
802.11an HT20: 20dBm 1 1.5dInsON <S7, 802.11an HT40: 20d Bm 1 1.5dEen 4MCS7
Receiver SensMeRY| 802.11a : -9368m* 2d6is46141)ps. -74dIhrn* 268/1)54resps 802.110: -9800m *201Inst INOps, +learn I RIBMIP11140PS 802.110 : -90.18m *e2dens.)6141)ps. -77d8rn 260m05404bps 802.11en HT20:•74011in ± 208mONIC97, 802.11gn HT40:•7105m • 200m0114a7
802.11an HT20:-71dBm 1 2d f5mOIC57, 802.11an HT40:48dBm • 2 dBmGMCS7
EnoyptIon Security| WEP: (64-Olt ,12841t key supported)
WPA/WPA2 P5K: TIC IP and AES en Creation (802.114) 802.1X Authentication supported
Wireless Security Protocol Support
Protocol
POWER
Redundant Input power| 5510 brood cast disable and enable
ARP, BOOTP, DHCP, DNS, HTTP, IP, 104P, SNIP, TO, UDP, RADIUS, SNMP, STP, RSTP
Dual DC I emits . 12-46VDC on •pi II terminal block
Power Cansurnotsan(b9.)| ?watts
Overload current protection| Present
Reverse polarity protection Physical Characteristic Enclosure| Present on terminal block IP-30
dimension (W X O x H)| 45(W) 495 (o) x lis(n)rm ( 1 . 77 •3. 74 • 4 .53 1 n0 1 4
Wait (9)
Environmental Storage Temperature| 3759
-40 to SSC (•40 to 185’F)
Operating Temperature| -10 to 70C(14 to 156’F)
Operating Humidity Regulatory Approvals (MC| 5% to 95% Non•cordensing
CE 194C (EN 55024, EN 55032), ?CC Part 151
EMI| EN 55032,CISPR32, EN61000-3-2, EN61000-3-3, FCC Part 15B class A
EMS| EN 55024(11C/6N 61000-4-2 ((SD), IEC/EN 61000-4-3 (RS), IEC/EN 61000-4-4 (EFT), IEC/EN 61000-45 (Surge), IEC/EN 61000-4-6 (CS),IEC/O461000-4-S(PM4F),IEVEN 61000-4-1 l(DIP))
Shock| IEC60068-2-27
Free Fall| IEC60068-2-6
Vibration| EN60950-1
MTBF
Warranty| 211477 hrs
5 years